Having problems with your KitchenAid Dishwashers ?

Clean light flashing 7 times I have tryed replacing ther thernistor and the heater element alread with no results


Answers :

Hi
\015\012If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset.
If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back for further assistance.
\015\012Daniel
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Clean light flashing 7 times I have tryed replacing ther thernistor and the heater element alread with no results


Hi\015\012If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, th ... KitchenAid Dishwashers

Model # 665.17032402 Clean light is flashing. Manual says to check heater circuit. How is the heater circuit checked? How is the heater element assembly replaced?


You need to check the thermostats in the heater circuit as well. The element is held in place my 2 nust from the bottom where the wires attach.eric ... Dishwashers

Candi cdi1012 beeps and lights flash after about 30 mins. It appears that the water is not heating. Do I need to replace the heater element?


... Candy Dishwashers

I have a kudso1flss6 dishwasher with the clean light flashing 7 times. Can I replace just the control unit or do I have to replace the heating element also? I also need to know how to replace the part or parts. Help!


Depress cancel button. Turn off power WHILE STILLL HOLDING DOWN cancel button, turn power back on. Viola! ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

4 years old with light use.fills with water.house fuse blows.reset house fuse & blows every time the door is closed.have striped to a point & can run the mashine if i disconnect the red wire to the heater element.it then fills & will not move on & obviously will not heat.heater element is expensive & looks time consuming to replace. ntc,thermostat,programmer or element ? some ideas or tests please


... Neff 24 in. S5457X0GB Built-in Dishwasher

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

F&P dishdrawer problem: I don't think the heater is working to heat water and dry, as dishes not very clean now and quite wet when cycle finished. The lights don't work anymore so have not had a fault code. How do you replace the heater element? Thank you.


First, open the door and look into \015\012 the tub and locate the heating element (if it is covered, remove \015\012 the lower dish rack and cover). The heating element has two terminals \015\012 which ex ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

SEARS/WHIRLPOOL DISHWASHER Model 665.16014401. The CLEAN light keeps blinking and washer will not run. Op. instructions say to check the heater circuit. Heater element tests at 12.9 Ohms and thermo unit at 55 K ohm and the unit I beleave looks like overtemp cut out is less than 1 ohm. these look like good #s to me so I suspect the controller p/n 8564544. When I look up the number online I find it has been replaced with 8564546, but the only picture I can find of it looks like the connections are


... Kenmore Dishwashers

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

Blinking cancel light, had broken element replaced and still won't work and blinking cancel light still flashing


You probably have to replace the latch and strike, as well as a switch that is on the latch assembly. It may only be the switch, but when you have it taken apart it makes sense to replace all three parts. Parts should be available on Amazon. ... Kitchen and Much More Dishwashers

Dishwasher will not start. Clean light flashes. Time display shows --. Manual states "The diswasher has malfunctioned". (Obviously) "Call for service to check heater circuit". Will replacing the circuit board solve the problem?


Hello, welcome to FixYa.\015\012\015\012I understand how vague those manuals can be, very frustrating.\015\012\015\012In regards to the fault, while the control can be an issue and ultimately require replacement...that is a wo ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

I have a kenmore ultra wash dishwaher model # 665.17039401 type 575-d the clean light flashes and that is all it will do now. the troubleshoting section say heater problem. before i change the element out is there anything else i should check???


... Dishwashers

Flashes an error code indicating a heater problem -- element looks good. what part may I need? Is it worth the price to fix, or should I replace the dishwasher?


Check the heater or the thermostat. If you have nothing to check them with remove and have someone with a meter check them for you . ... Kenmore 24 in. 17032 Built-in Dishwasher

CMA-180 Dishmachine-4 years old, used up to a maximum of 5 times a month. After 10-12 loads it shuts down, alto the lights are on, it won't start for about 30 minutes. Is it possible there is a heating element in the machine that needs replacement, or our water heater is not keeping up?


... Cma Dishmachines CMA 180 Free-Standing Dishwasher

Extremely heavy limescale residue on all items after dishwasher has finished. water temp in house has been turned down. Had water tested by city water company and results were clear. 12 months ago maytag replaced heater element under recall, but dishwasher always seems too hot. Neighbours do not have this problem. Any advice would be most welcome.we only use quality powder and rinse aid. Have cleaned dishwasher numerous occasions. model MDB4651AWS1 SERIAL # NW5015848


Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... Maytag 24 in. MDB4651AWS Stainless Steel Built-in Dishwasher

Clean light is flashing - I know itsays to check the heater circuit. Is this something I can replace?


Really you are correct about the flashing light indicating the heater circuit.This is a task for the experts at the service centers because there are specific tools such as allen keys and meters for reading the rating of the circuit for p ... Whirlpool GU2400XTP Built-in Dishwasher

Clean light is flashing and I have replaced the heating element model #DU1055XTPQ3


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Whirlpool Dishwashers

Clean light flashes 7 times and will not run wash cycle I have replaced heat element


Big guy this happened to me the other day do this it will reset computer you ready hit these buttons heated dry normal heated dry its a code all lites will then come on that resets computer ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Whirlpool gu2300xtsso clean light flashing and would not cycle. I replaced the heating element and it will go through a complete cycle, but will not wash.


... Whirlpool Dishwashers

Clean light still flashing after replacing heating element


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1431 seconds