Having problems with your KitchenAid Dishwashers ?

My kitchenaid dishwasher is blowing the internnal fuse. Ideas?


Answers :

Replace with kit and be sure to REPLACE THE CONNECTORS that come with the kit!

Kelly
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kitchenaid dishwasher is blowing the internnal fuse. Ideas?


Replace with kit and be sure to REPLACE THE CONNECTORS that come with the kit!Kelly ... KitchenAid Dishwashers

My kitchenaid dishwasher keeps blowing the thermal fuse behind the door.. Have replaced it 4 times. Now it will run through one cycle and blow fuse. Any suggestions on what other part could be causing this problem?


... Dishwashers

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

Kitchenaid Dishwasher thermal fuse keeps blowing


The reason the thermal fuse is blowing could be due to a loose contact in the wiring or the motor is requiring more power to operate causing the fuse to burnt again. ... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

Kitchenaid Dishwasher KUDP01ILBS6 blowing thermal fuse


... KitchenAid Dishwashers

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

I have a KitchenAid Dishwasher KUDIO1iLBS2 and none of the lights come on and if I press any of the buttons nothing happens. The unit is getting power to it as I shocked myself. I did ordered and replaced the control board and still nothing is happening. Any suggestions or ideas? Is there a reset button or is there a possible fuse that is out that would make the lights not come on? Please help.


... KitchenAid Dishwashers

Electrolux ESL 63010 dishwasher. This worked fine until the door catch broke. I replaced the catch but could not remember which way round the two electrical leads went (red and black). I tried both ways with the same result. The lights come on the control panel and I can change the programme, but on closing the door the house fuses blow. I have checked the earth cable is fine. Any ideas?


Red - is active powerblack - ground or neutral ... Electrolux Dishwashers

Hotpoint Dishwasher BF1620 blew the main fuse circuit in fuse box during mid cycle wash? Re-set main power fuse circuit but now as soon as Dishwasher switched on immediately blows main kitchen power fuse in fuse box? What is problem?


This is happening because you have a very bad fault, a Phase to Earth short, problem. Leave machine UNPLUGGED, Breaker/Fuses OUT. do NOT use it, nor Touch it, It is possible to get severe electric shock. PLEASE get a registered serviceman to inspec ... Hotpoint 23 in. BFI62 Built-in Dishwasher

The fuse in the plug keeps blowing. Initially it would run for a while - sometimes 3 or 4 cycles - before blowing. It now blows the fuse the second that I plug in to the socket, even with the on/off button on the front of the dishwasher set to off.I'm keen to take it apart, but it's full of water as it blew mid-cycle. Is there a clever way to empty the machine without the power being on, or do I need bits of hose and sponges?A schematic blow up would also be extremely helpful.


Lower the outlet hose into a washing up bowl, it should then Drain. Check the heater to see if it is earthing you get to it by removing the right hand side panel. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

Karcher 720mx My unit keeps blowing fuses, every time i release the trigger it seems to have a power surge and blows a fuse. Any idea if it can be fixed?


... Pressure Washers

ZANUSSI DA6141 Dishwasher Stops about 10min in, and it blows the fuse in the plug, open the door and water is hot, I change the fuse and set it on drain and it drains ok. I looked at the On/Off Switch it appeared to be discoloured so I ordered a new one changed it with no problem but the dishwasher stopped at exactly the same point (I know this as I marked the dial) Any help would be great thanks Nick


... Zanussi 24 in. DA6153 Free-standing Dishwasher

We have an Hotpoint FDW70 Dishwasher that for some time has had an A10 fault which although stops the machine some times 70% of the time it does a full cycle. However it is now tripping out the electric at the mains. It is not RCD protected, but does not blow it's own 13amp fuse or that of the fused extention lead it is pluged in to. Tends to blow after about 5 minutes. I know about the fault code A10 being 'Fill Valve Triac' but as not an engineer what is that? and what parts are needed and or


Hi the fill valve triac is the plastic vlave that the inlet hose connects to you can get them for about £10 you reset the machine after replacing it by switching it on, pressing the power button leaving it off for about a minute then switching ... Dishwashers

Nothing happens when I push buttons on the control panel of my dishwasher (KitchenAid KUDS011 JBS1). The drain is clear. It has been suggested that it may be the thermal fuse. What is the part number for the thermal fuse in this dishwasher?


The model number for your dishwasher is actually "KUDS01IJBS1". The character before the "J" is a capital "I" instead of the number "1". I just wanted to clarify that in case you need it for future reference.\015\012\015\012You are corr ... Dishwashers

Bimetal fuse The incoming power was blinking off and on due to a storm, it caused the bi metal fuse to fail in the dishwasher when it was not operating, the fuse was replaced with kit #w10258275, now two weeks later the fuse has failed again while operating.These fuses are expensive, I would like to know the value (amps) of these fuses so that the system can checked to try and find out the reason for failure, or maybe you might have an idea where to start. Thanks Tad


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Kudc10fxss4 I have a KitchenAid KUDC10FXSS4 w/o any power. Circuit breaker is on, and it's getting power. But there are no lights on the display. I called a parts place to see if I could order a thermal cut off fuse. But the representative stated there is no fuse listed for this model. Any ideas on what would be causing a loss of power? Seems odd/wrong to me that there wouldn't be a fuse. If there is a fuse, would it be located in the door (the control is built into the door, such


... KitchenAid Dishwashers

My KitchenAid KUDPO1FLSS1 dishwasher keeps blowing control moduals


... KitchenAid Dishwashers

My dishwasher so my dishwasher seemed to have quitworking during a cycle. like breaker triped or something. i checked the breaker and thats fine. it seams like its hard wired in though. Would that be right? and is there a fuse or something that could/would blow during a wash? I dont know what model it is or anything it was in the house when i got it. The dishwasher is built in and it seems decently old its a kenmore ultra wash and it has like 10 buttons for the differend cycles on the left and a


Sounds like the fuse on the control blew. you can replace the fuse for\015\012around $20 or you can cut and splice the wires for free. If that doesnt\015\012work then you may have a loose conection in your junction box under the\015\012dishwasher. ... Kenmore 24 in. 15932 Built-in Dishwasher

Hi I have the Kitchenaid dishwasher KUDIO1FLSS2 and all the buttons work except the two most important ones, the heavy and normal cycle. I had a service person out about 6 mo. ago and he said the control panel was about to go bad and replaced a fuse. He ended up coming again a week later and replacing the fuse with a stronger fuse. Now it's acting up again and I'm sick of hand washing dishes and don't feel like handing over another $300 or more if I can do it myself or maybe I just need to buy a


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Ignis built in dishwasher keeps blowing fuse


... Dishwashers

Diplomat dishwasher blows fuses


I would disconnect the heater then run the unit.If it runs the heater is bad,if the fuse blows again the motor is most likley bad.make sure there are no water leaks.let me know.happy holidays ... Dishwashers

Zanussi Dishwasher DA6152 Blowing Main Fuse


A guess is that the water has leaked into the motor, and the machine is shorting out. As a retired firefighter, may I please recommend you do not try to start it again? It could start a fire. It is probably time to buy another dishwasher. ... Zanussi Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1472 seconds