Having problems with your KitchenAid Dishwashers ?

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Answers :

Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reconnect,if this fails,then replace the electronic control assembly located behind the user interface you previously replaced
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Bosch Dishwasher I have just moved into my flat where there is a Bosch dishwaher installed in the kitchen. I have tried on a number of times to get the dishwasher to start a programme but for some reason it fails to start. It does switch on but I dont know how to operate it. I dont have a manual for it so have not a clue what to press to get the programmes running. I would be grateful if you could help. Bosch Dishwasher logixx Model Number SGS6952GB/13 Installed 2001


Dear Saps,\015\012Go to https://portal.bsh-partner.com/portal(bD1kZSZjPTAwOQ==)/PORTALFRAME.HTM for a pdf download for an Intr ... Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

Hi just had new dishwasher put in its a diplomat intergrated dishwasher aca9102, only used it once and started beeping towards the end of the cycle. thought it might be coz i didn't put salt in it, and had tablets instead of detergent so put salt in and detergent in but couldn't get rinse aid. started the program on normal wash but started beeping 10 beeps straight away and the first three lights out of 6 are flashing on the control panel. could it be coz theres no rinse aid in it? please someon


Dear tracy83, \015\012\015\012we have an aca9102 diplomat dishwasher since april 08. we now have a fault with dishwasher but cannot locate our manual. could we arrange rto have a copy of your manual? sorry for being up front but cannot ob ... Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Model 66516039402 Type 575-0 Green light flashes intermittanly on Clean Problem is I cannot get the dishwasher to start. When pressing Start it flashes red a few times and then stops


... Kenmore Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

Smeg Dishwasher Hello I have a smeg dishwasher - built in, push button. It has stopped working - the program start and you hear it drain but that's as far as it gets, no water appears to be getting in. A couple of times the last 2 program buttons flash or the rinse light is on when we open it. let me know if you have any thoughts on this - I'd really appreciate it. thanks Diane


Replace the timer/control board ... Dishwashers

Dishwasher I turn on the dishwasher and all the buttons flash, (no noise) i can go through and try and select a setting but when i press start nothing happens the buttons just keep flashing? Do you have an instruction manual or can you tell me how i would get one?


What brand is it? go to that web site put in model number and download it there. also you might have the controls locked press and hold the heated dry button for three seconds to see if that unlocks the controlls. ... Dishwashers

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

FDW60 dishwasher Hi My dishwasher is about 15 months old and the problem I have is that it seems to stay on pump and the Ecco45 light is flashing.  A repair company looked at the machine and said that the motor looked like it was leaking and water was getting in the bottom setting off the micro-switch.  He contacted Hotpoint who fitted a new motor today at a cost of £89.85.  Went to use dishwasher tonight and we still have the same problem.  The dishwasher started the washing programme for about


I've just (as of 10 minutes ago) had the same problem. I followed the advice given elsewhere in this forum and removed the bottom cover - water running out so needed a big towel to mop it up. I stood the machine upright and restarted it - no problem! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.


... Smeg Dishwashers

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

My maytag dishwasher MDBH970AWQ Quiet series 300 is more and more often not opening the soap dispenser. Also the number 9 flashes and can't seem to get it to go away. If I try to start the dishwasher over again with the hopes of the dispenser opening the dishwasher just runs for the countdown of 9 to zero. Help!


... Dishwashers

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2192 seconds