Having problems with your KitchenAid Dishwashers ?

My dishwasher ran good amonth ago .Today when I tried to run it ,it only runs in the dry position. What could be wrong?


Answers :

Http://www.acmehowto.com/howto/appliance/dishwasher/dishwasher.php\015\012
\015\012Hi, well to assist you to troubleshoot your problem, i have given you a site above, that will step you through, how to troubleshoot and hopefully resolve your problem. If you do wish yo DIY also one MUST obtain a service manual, they may be able to be found on the 'net, or from the manufacturer.\015\012
\015\012Unfortunately, with just this symptom, it's pretty hard to tell exactly what's wrong, other than it maybe a sensor, the door switch, the pump, the inlet valves, the "Brain" the... the... you get the idea.. as really most "Faults" simply stop it from working, leaving it mutely idle.\015\012
\015\012However first have a look at this below,it may or may not apply, but also may well be worth a go... I leave it up to you.\015\012
Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle.This should NOT be done. You should NEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.\015\012\015\012\015\012
\015\012
\015\012
\015\012\015\012it is my professional recommendation, that if you cannot or do not wish to DIY, then to get the best and cheapest result you should get a "Quote" for repair, from, an, Approved Service Center. Now, this point is very important for a good result, Always contact, their "Local" or a, "Head Office" Of Your brand Model number, in your case. Ask them, for a referral to an authorised servicing center, where you then FIRST, ask ONLY for a "Quote" as to the cost and type of repair. Now, when you get the information you want, then you can decide as to repair of replacement. \015\012
\015\012
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher ran good amonth ago .Today when I tried to run it ,it only runs in the dry position. What could be wrong?


Http://www.acmehowto.com/howto/appliance/dishwasher/dishwasher.php\015\012\015\012Hi, well to assist you to trou ... KitchenAid Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Our bosch shu9902uc dosnt clean the dishes,ive tryed to clean out the drains,blew compressed air thru the drain line,cleaned out the sprayers,still it dosnt clean food off the dishes. water plenty hot and they dry good too it dosnt sound too good when its running too


Make sure you clean the sprayers out real good,if theres debris on the end nozzles they dont spin around too good,also pull out the little service plug that protects debris from getting in the impeller.\015\012i found a little chunk of wood in ... Bosch SHU9922UC Built-in Dishwasher

Engine does not start. I ran it about two weeks ago and it worked fine. I took the spark plug out and it was dry. I made sure there was gas in it. I tried some starting fluid by spraying into air intake and it start running for a short time until the starting fluid ran out. I removed the carb bowl and there was gas in it. However the inside of the bowl and the float had brown deposits and looks like rust. So I think the main jet has been clogged up with a particle. How do I clear it? Where do I


Try cleaning the carb with gumout spray and a little compressed air, be careful to reassemble the float and needle valve exactly as you found it. ... Northstar Pressure Washer 3000 PSI

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

It appears that the dishwasher is not getting enough water. I have made sure that there is nothing blocking the door area so that the soap can dispense and I have reduced the amount of detergent to maybe a 1/2 Tablespoon. Have tried both powder and liquid detergents. Ran a sani clean cycle with the Jet Dry product for dishwasher used in the rural. I also run the hot water in the sink prior to starting the dishwasher to ensure the water is hot when it comes into the dishwasher. The detergent


Hello,Welcome to FixYa.Based on your description you`re experiencing the ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Bosch dishwasher model SHV66A. New in 2004. Has worked well since then, but for last couple weeks something's up. Dishes aren't clean. Residue remains on everything. Food looks caked on & dried to plates. Silverware a little better but not much. Tried running a couple cycles with vinegar, no help. Took out strainers, etc. on bottom of washer & cleaned out; no help. Just ran a cycle now - - opened midway and it appeared the arms were both spinning. Also, water seemed warm (maybe not super


Hi\015\012\015\012If you are observing that the dishes are\015\012not clean, then you'll need to follow certain steps to be sure where exactly\015\012the issue. First thing to check for is\015\012the deter ... Bosch Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

Pressure washer has been sitting up for about 2 years.. worked perfectly before I parked it.. lol.. But, I put a new spark plug on, cleaned the filter, sprayed carb cleaner in it drained the gas tank and added new gas.. But it still does the same thing.. It starts in the choke position, runs awhile, and then shuts off. While its running, I tried to put the switch in the run position and it kills. Just wanted to see what an expert would say about the matter before I Brake it down. thanks


... Briggs and Stratton 020275 Elite Series 3400 PSI Portable Gas Pressure Washer

Dishwasher won't run. Normal wash blinks. We tried pushing normal wash and heated dry and repeated that. Didn't work. Also tried high temp then heated dry twice. That didn't work. Any other options to try???


... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

So i have a maytag jetclean eq plus MDB7100AWW not sure how old it is as it was in my condo when i moved in 6yrs ago and there was no paperwork with it. The dishwasher worked fine until a couple days ago. The last load that i washed came out with a white film on everything, i checked the jetdry it was empty so i filled that and ran another load, everything was still covered in the white soapy film. So I tried running a dishwasher cleaning product through it, that didnt help, i tried running it w


... Maytag Dishwashers

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Dishwasher is continuously running and is not turning off. It finishes a cycle and then starts a new cycle. Also not drying the dishes good and we did push the added heat function button as well still not drying to dishes good.


... GE Dishwashers

I have a kitchenaid dishwasher, SS, model # KUDIO1ILBL6. When you press the ''normal'' button to run it, nothing happens. Tried other cycles and same thing, the green light goes on above the cycle but its just not starting. I tried resetting by opening, pressing high temp scrub then energy saver dry, high temp scrub, energy save dry, then close and hit cancel. Is there any other combo to reset it? or does it sound like something else is wrong? thanks!


... KitchenAid Dishwashers

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

I have a model 5000g. it might have 15 hrs. total running time on it. when i tried to use it last it would not build pressure. i took the pump apart and cleaned and regreased it. everything looked good. ive got good pressure to the pump but just a small spray out the wand. when running there is no real load on the engine. it has always been kept inside in a warm enviorment.


... Karcher Pressure Washers

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Dishwasher stench It's BAD. I had the dishwasher guy out - there's nothing in the filter. He said everything was fine - run shome dishwasher cleaner thru it. We tried that - no good. I looked online and saw there should be a loop in the hose (there was not). I got that taken care of. That guy said run some bleach thru it after and we'd be fine. I did. Still stniks. It's okay right after we run it, but gets skanky in about 2 days after running. I had another plumber today for something else. he s


You might have luck with some enzime cleaners,some washing liquid comes with it,have you tried bakeing soda? the in side is made of plastic . ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Dishwasher runs and cleans but does not dry. I have tried numerous differend kinds of drying agents but none help and the level of drying agent does not go down or down very little.


Hi,Check your heating element.. Dishwasher ... LG 24" Built-In Dishwasher - Black

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1399 seconds