Having problems with your KitchenAid Dishwashers ?

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


Answers :

Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers

Water is flooding out the bottom of the dish washer door, the door seals are in good condition, it seems to be over filling with water


... Candy 24 in. CD950 Free-standing Dishwasher

I have a Frigidaire dishwasher, FDB-1100RHC, that is not cleaning dishes. My fiance cleaned the trap at the bottom of the washer, removing both the small basket and the larger mesh grid. After replacing both, the washer doesn't seem to have enough water pressure to spin the lower and/or upper arms. If I interrupt a cycle and open the door, water is dribbling out of the upper arms, but they are not rotating and do not move from whatever position you place them in. Both arms are completely uno


Hello :)don't feel bad, I run into this kind of problem at least once a week.\015\012It does sound like the pressure isn't there so you're not getting water to the upper spray arm. What you need to do is take the pump apart, which i ... Frigidaire Dishwashers

Doesn't clean my dish washer seems to work fine but when its finished the tablet i put in the door is still in one at the bottom of the dishwasher and the dishes aren't cleaned properly. i've checked it about halfway through and the water does get hot. please help.


Is your water heater set at 120 degrees if not set it to it ... Hotpoint 23 in. BFI62 Built-in Dishwasher

Dishwasher has stopped during programme - door may have been opened during cycle??!! - although cycle had only just started. bottom of washer has water in but cant seem to restart on ANY programme - pls help!!! have turned off at power and back on etc - no joy :(


... AEG 24 in. Favorit 80860iW Built-in Dishwasher

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

While on vacation our house had been checked at one week later &again 2 weeks later, @ 3 weeks check, floor in front of dish washer & entire kitchen had standing water , as DW door was opened bottom of DW had water standing up to bottom of door . Water supply to house was shut off before we left. , Since we returned home we have used DW daily with no indication of where this water came from. Any ideas ? Thanks, Bob


Take a long shot. Say your mains leak a little, quite possible, and you machine's inlet solenoid valve leaks a bit, say about a litre a day - you probably would not notice it during the normal course of events, in a week it would leak a ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Whirlpool quiet partner 2 Water leaks from the bottom of the door, alot of water, we can watch it pour out. The door is closed all the way. I dont see a gasket along the bottom of the door where it would hit the frame of the washer,


\012Hello, Thank You for using FixYa. I will be helping you today.There is no seal for the bottom it is an air gap. If there is a damaged lower spray arm or crack in it water will come over that edge. Check the spray arm for damage. Open the do ... Whirlpool GU2400XTP Built-in Dishwasher

Leaking water from underneath the front door. Water seems to be leaking through the bottom plastic seal. and sprays against the inside bottom of the door then drips onto the floor. Help


Hi,Leaks under the door can stem from a variety of causes. If your\015\012dishwasher is very old, the tub itself may have become corroded and may\015\012have holes. Inspect your tub; if you see such damage, use an epoxy\015\012patch kit t ... Dishwashers

Water comes gushing out of the bottom of the door whenever water goes in. It seems like the seal at the bottom of the door isn't doing it's job. What can I do to fix it?


... Amana 24 in. ADB1500AW Built-in Dishwasher

I have a Maytag DWU8250BAX and the thing leaks like crazy. I just replaced the door gasket, but that is not the problem. When I took a closer look at the door it seems as though the water is getting up and into the door through a space in the bottom of the door. It seems to me like there should be another door seal to fill a gap that sits between the door hinges. If anyone knows if there should be a seal here and then what the part number might be that would be great. Thanks!


There is an airgap under the door..it should spray up and run down the door not spray up under it..look for crack or hole in spray arm..if there is the wrong soap in it it will flood out with lots of bubbles..just have to flush it out. lastly, if you ... Dishwashers

FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Water remains at bottom after dish cycle is complete . Dishes come out clean and everything seems normal except for the water that remains at the bottom of the dish washer. I realize that a small amount of water is usually there but this is too much.


Set the controls to off then power off at the mains for 30 mins and then power mains back on and run a drain program or a full wash program. If the water won’t drain away then the most likely problems are the door interlock switch is faul ... Whirlpool Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I stopped using my dishwaser because it left crusted on food particals even tho I rinced them well(so I thought) before loading. It was as if they were just being dried crusty. After a couple month I noticed a bad smell. I looked in the dishwasher to find standing water in the bottom. I ran a little CLR through and it cleared out. But a couple weeks later again there was water in the bottom. It seems as if the water from the sink is draining into the washer. If I run it it runs thru just fine, n


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Estate 24 in. TUD4700KQ / TUD4700KB Built-in Dishwasher

I have a Hoover dishwashe HND 6515. I put it on the universal 65c programme this afternoon and sfter 5 mins it started a continual beep beep beep noise and the red light on the universal button was flashing, I then notices it was emtying water all over the kitchen floor, seeming to come from under the bottom of the door. I turned it off and when it finished pouring out water opened it up and the bottom of it is full of water which will not drain away. I have checked the filters and they are all


... Hoover Dishwashers

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

Hello, I have a Frigidaire FDB510, after a few minutes of running water starts pouring out of the bottom of the door.I have replaced the wiper or sweep seal at the bottom of the door, the gasket does not seem to be bad, (it actually does not wrap around the bottom of the door anyway). Am I not draining correctly i.e. float,pump, etc. I sure could use some advice. Thanks


Ckd spray arm be sure it is not binding on something also ck for possible split in spray arm look close some are almost invisable ..when water is pushed through spray arm the seam will sometimes separate..also watch for oversuds ... Frigidaire Dishwashers

After I run the dishwasher, water stands at the bottom and it smells. I have had the dishwasher for five years. The washer seems to be working properly it's just that water stands at the base of the washer. Is it normal for water to always stand there?


No it's not normal, you are probably having some cloge in the drain pipe, you could try with a pice of wire to pick it up or hose it down, or use some comercial unplaguners like mr. muscle or something like that, i think that this would do the trick ... GE Nautilus 24" Built-in Dishwasher

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

Ge Triton dishwasher GSD5500GOOWW was not cleaning like it used to- I cleaned screens at back bottom-very dirty- also-detergent cup stuck opne - took door apart and got it unstuck - it works fine now. - it seemed to do better but now it is cleaning poorly. It seems to fill and start a lot sooner than before - after 30-45 seconds it starts up. I tested the water temp and it is 90 degrees! Hot water coming in is at 105 degrees. Also - it is leaving a white residue on dishes - didn't do that be


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1323 seconds