Having problems with your KitchenAid Dishwashers ?

I have a Kitchenaid Dishwasher, model " KUDL031VWH4", the buttons "Normal Wash and Start" blink rapid continuously and there is water sitting in the bottom. I turned the power off for 15 minutes ti n

\015 Kitchen aid model KUDL031VWH4\015

Answers :

Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kitchenaid Dishwasher, model " KUDL031VWH4", the buttons "Normal Wash and Start" blink rapid continuously and there is water sitting in the bottom. I turned the power off for 15 minutes ti n


... KitchenAid Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Cycle counter goes to 1, but continues to agitate, does not pump the water out, nor does it go to zero. The counter will stay on 1 indefinetly, if I use the pump button, there is soap residue in the bottom of the machine. I called the Sears repairman, he was here about 10 minutes, unplugged the machine from the wall and said that probably I had a power surge and that would solve my problem. It did not. I live in a very small town, I will have to take my dishwasher to Las Cruces (101 miles awa


Hello, welcome to Fixya.\015\012\015\012I`ll start by saying how unfortunate it is to have too many so called "pro`s" trying to diagnose appliances who have no business doing so if that is how the repair-person you spoke of e ... Bosch Dishwashers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The engine starts cold after 2 or three pulls, runs ok initially, but seems to have slightly less power. After a few minutes I can turn off the choke. When teh engine warms up and runs for about 15 minutes, there is a definite power decrease and the motor sounds like it will stall. If I paly with the choke, it does not stall, but has little power to pump water. If the engine does stall or it is turned off, it will not restart until it cools down.


I would first try draining the carb bowl, if you look at where the choke lever is and look below that you should see a clear red tube with a flat head screw below that, if you just turn the screw out the carb will drain. If you still have an issue yo ... Karcher G3025OH Pressure Washer

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher

I have a Hoover dishwashe HND 6515. I put it on the universal 65c programme this afternoon and sfter 5 mins it started a continual beep beep beep noise and the red light on the universal button was flashing, I then notices it was emtying water all over the kitchen floor, seeming to come from under the bottom of the door. I turned it off and when it finished pouring out water opened it up and the bottom of it is full of water which will not drain away. I have checked the filters and they are all


... Hoover Dishwashers

I have a Bosch SHU66C02. I opened the door to stop it from running temporarily, while it was sitting not running, it leaked all of the water out of the bottom right corner of the door, and when I went to start it later it just hummed but the timer didn't go down for over an hour. I tried to put more water in but as soon as I started I could hear the water added to drain. I turned the breaker in the fuze box off to it and let it sit for over an hour, but when I restarted, the timer was still at


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's


... Kenmore 13719 / 13712 Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Dishwasher turns on but blades don't move - water sits on bottom


... GE 25 in. Profile PDW8200J Built-in Dishwasher

I have a Kenmore Elite Ultra Dishwasher and the cleaning light is flashing. I have tried pressing the start/resume button and closing the door within 3 seconds. I am not able to turn on my dishwasher. I have tried turning off the power for 20 minutes but when power was restored the green light continues to flash and the dishwasher will not work. This machine was installed in May 2008. Help!


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Dishwashers

Dishwasher fault had leak,when opened bottom plate, could not see any obvious leak problem,hand dryed what componets i could. made sure no wires were loose then screwd back bottom plate,turn power back on but power button flashing continuously know,any advice plz


The flashing power button is a bad sign. You may have flooded the circuit board out or there may be a bad component as a result of the flood. Difficult to know from here.\015\012\015\012Most flooding on dish washers is caused by a faile ... Dishwashers

I have a Siemens Dishwasher. I'm not sure of the model but it is built in, has concealed controls and was purchased about 6 years ago at Best Buy. It sort of looks like the SL85. When started, it runs for a few minutes and then starts to make a horrible sound. ALmost a grinding sound but may also be like water trying to get through a small opening. The sound does not stop even after turning off the DW and even the power to it. Only turning off the water supply does it stop. Help?


... Siemens SL85A705UC 24 in. Built-in Dishwasher

Model 818s stops mid cycle and beeps continuously. water not drained out. water on floor. no lights on. shut power off and leave 1 hr. turn power back on and still beeping


... Fisher and Paykel Dishwashers

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


You just need to clean the pump area in the bottom of your unit :)try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :) ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??


You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1926 seconds