Having problems with your KitchenAid KUDA03CT Built-in Dishwasher ?

Both Heavy Duty and Normal wash buttons are blinking non-stop at once. Cannot get them to clear or stop. Dishwasher will not start because of this.


Answers :

Repair Help & Product Troubleshooting for KitchenAid KUDA03CT Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

Both Heavy Duty and Normal wash buttons are blinking non-stop at once. Cannot get them to clear or stop. Dishwasher will not start because of this.


... KitchenAid KUDA03CT Built-in Dishwasher

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

Hi - I have the Miele G 2470 dishwasher. It starts, and I have it set at "2 in 1 Tab" and on "Normal". I close the door and the machine makes a sound like it is starting, but then after abiut 30 seconds it starts alarm beeping and doesn't run. When you open the door it shows the light is now on next to "Intake/Drain". To stop the beeping I have to press the "off" circle. This sequence happens each time. what do you recommend to get it to work? thank you very much. Lori.


You could check into the User's Guide online manual below:http://safemanuals.com/414159.php?k=41da0c038c6dca28da72cf9056db1c61&ID=63815&q=MIELE%20G2470 ... Miele Dishwashers

When I start the dishwasher, it sounds normal. A few minutes after it starts, it makes a loud, thumping noise that lasts for several minutes. After a while, it stops making noise, but about half way through the cycle, it starts making the loud, thumping noise again. It's loud, annoying, and does not get our dishes clean. We have to wash several dishes by hand AFTER we have run the dishwasher.


I have made the assumption that your d/w is a siemens machine, however if not pls repost with the make and model.\015\012There are a few possibities...check the spray arms are clear by removing any blockages in the holes, check that there ... Dishwashers

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

My kitchen aid dishwasher (8573025) "normal", "light china", "and "cancel" buttons are blinking. I can't get them to stop blinking and cannot get the dishwasher to start .


... KitchenAid Dishwashers

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. Thanks


... Whirlpool 24 in. GU3600XTRY Stainless Steel Built-in Dishwasher

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Miele Dishwasher G643SCVi- Get a whistling sound when the dishwasher starts. Lasts for 20 seconds, stops, and continues again for 20 seconds. It does this 3 or 4 times and then it is normal. I have not done anything at this point to fix the problem.


... Miele Dishwashers

Our Asko D3112 was not draining, so we had maintenance drain the hoses to clear any blockage but it did nothing. They said it must be our pump not working. I ran one more cycle to see if things went back to normal, however now our pump won't shut off. We have to unplug the machine just to get the pump to stop. We had a repair technician come to look at the dishwasher and he says that it is a problem with the control panel/computer system. Something tells me it is a merely a loose wire and that w


Check your manual to see if you have a drain pan at the bottom of the unit, and a 'float' that checks for water collecting there. On at least some Asko models, water collecting in the pan causes the float to rise, which then changes the operation of ... Asko 24 in. D3112 Free-Standing Dishwasher

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

It starts running then stops - starts pumping in water then stops, etc. burning plastic smell near top... doesn't leak, gets power, but begins to fill, then stops - might start to drain (pump), but then that stops too...


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

When turned on the pump operates as normal, stops then starts aga


Hi.Regarding the fill problem, the electronic control board rarely fails in the way you described.When filling stops beforetime in the cycle, this is caused by the water level sensing device.Before replacing the ti ... LG 24 in. LD-12BW5 Free-standing Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1306 seconds