Having problems with your KitchenAid KUDC02IRB Dishwasher ?

Will not feed water to unit when turned on? - KitchenAid KUDC02IRB Dishwasher


Answers :

Repair Help & Product Troubleshooting for KitchenAid KUDC02IRB Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will not feed water to unit when turned on? - KitchenAid KUDC02IRB Dishwasher


... KitchenAid KUDC02IRB Dishwasher

Dishwasher (Model # SHU6806UC), unit is about 8 years old, very light use, less than once a month, and no previous problems. Turned on unit and after about 10 minutes, I found water on floor coming from dishwasher. Turned unit off and turned off water shut-off valve. Removed dishwasher from cabinet. Found mice had chewed a hole in water discharge hose under unit, inspected all hoses, and found another hole chewed in the 13" flex hose in the front of the unit. Also found the float chewed to alm


Hi,\015\012 Check the valve is open where the supply gets its water from the sink supply.There is a garden hose type swivel adapter after the valve, Close the valve tightly and then unscrew that hose coupling and see if the hose is full of w ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

I have a Whirlpool dishwasher model number DU1055XTPQ4 that is not cleaning the dishes. When the dishwasher is working, the bottem arm is turning and water comes out the holes. The middle arm has some water coming out, but does not turn. The top arm does nothing. It appears I have a pressure problem. I took out all the arms and cleaned them, along with the plastic tube that feeds them water. They had some build up on them but not much. I have the same result as before. I took off the


... Whirlpool Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Water was turned off while we were on vacation. Wife ran dishwasher without turning on the water. Turned on the water this morning, however unit won't pump water into the washer .


\012Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... ... Maytag Dishwasher

No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks


SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

The clean light on my Kitchenaid Dishwasher model KUD124SEBL4, stays on even after opening the door after w wash. Also 4 out of 5 time when you start the dishwasher no water turns on you have to cance


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

Bosch Integra 500 dishwasher turns on and starts wash cycle, turns off after 90 seconds and then there is no power on the button panel at all. The dishwasher is full of water. Now the unit will not turn on or off. There is power to the outlet the dishwasher is plugged into.


Your controlboard is no good. find out if its a recall unit go to thermador.com which is the company that owns bosch and they can tell you the price if you have to oreder it or if its free for part and you pay labor to install ... Bosch Integra® 500 SHX46A0 Dishwasher

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Is it common for Kitchenaid dishwashers to have water pooling inside them? It's almost like the valve for water coming in isn't shutting all the way...in the middle of the day, we'll find water inside the dishwasher...it drips out the front when you open the door...but when you turn it on, it doesn't have any problem draining the system...mysteriously, we find water in the bottom...what's up?


There is a rubber flapper valve that keeps water from running back into your dishwasher. It's a $5.00 part, but it's a bear to get to,\015\012\015\012You have to pull the drain pump to access this flapper.\015\012\015\012Also ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

When the dishwasher is turned on, no water goes into the unit.


... Miele Dishwashers

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

Our dishwasher seems to have stopped working over night. The power button comes on and the unit beeps to acknowledge start, but then there is only a very light hum & the unit does not start. No water comes through the unit and it just hangs at the light hum. We have not turned off any water but just checking if there is a simple solution? Adam Hdw100sst


Suspect pump.on start the pump will activate to remove condense water from drying the last load.if the pump does not start then the next step of adding water to start wash cycle will not happen.ensure pump is not blocked ... Dishwashers

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

I have a newly installed Kitchenaide dishwasher. The copper pipe is secure under the sink and appears connected properly to the dishwasher. When I turn the shut off valve on, water begans to run from underneath the dishwasher. There is no water under the sink. The plastic hose does not seem to be the problem.


You should be able to remove the panel below the door and see where water inlet hose is connected to the solenoid valve. I'd bet that's where it's leaking since you say it's newly installed. ... Dishwashers

Have a 9 month old Smeg Dishwasher D612SDX. Disconnected water feed and re-connected. Problem is that dishwasher panel now flashes 4 & 5 when turned on, as if dishwasher is running. It isn't running! but can't reset by turning on/off, pressing program key or start key. Any ideas?


Looks like it is either a fault with pump/ inlet valve or with the control panel, let me check the code. Is the appliance running or not? ... Smeg Dishwashers

When I turn the dishwasher to on the unit just hums. No water , No nothing.


You need to get hold of a multimeter and test for voltage at the solenoid, if there is voltage there then the solenoid is faulty and needs replaced. If not then it will be a controller issue. ... Dishwashers

Own a KitchenAid dishwasher, model KDC-21AD. Unit stopped shortly after startup cycle began. When cycling thru the various wash cycles, I hear a slight hum when selector switch is at the "pots/pan" selection. About 2" of water is standing in base of dishwasher and it will not start. Checked the KitchenAid site and they do not list my dishwatcher. Would like to be able to repair myself or have it done at reasonable price.


... KitchenAid Dishwashers

I've had a Miele G892 SCU PLUS dishwasher for a long time. Today a problem started that results in a flooded floor. Water keeps flowing into the dishwasher - even when the unit is turned off. It seeps in very slowly, but within15 minutes there is enough to overflow & flood the floor. My guess is that there must be some kind of sensor that isn't working, or the coresponding mechanical switch that shuts off the water is worn or slightly stuck open a bit? Anything I can do / check, short of the re


... Miele Touchtronic G892 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2167 seconds