Having problems with your KitchenAid KUDC02IRB Dishwasher ?

Pots not getting cleaned. I clean filter but problem still exists. Do i need to replace water inlet valve?


Answers :

Repair Help & Product Troubleshooting for KitchenAid KUDC02IRB Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pots not getting cleaned. I clean filter but problem still exists. Do i need to replace water inlet valve?


... KitchenAid KUDC02IRB Dishwasher

Maytag MDB 4000 AWB. Not cleaning. not getting water now. pressure was low when i was getting water. . Soap dispenser would not open as well. I replaced the motor on the soap door. cleaned the float switch. Tested continuity and cleaned out water inlet valve. Still not getting any water


... Maytag Dishwashers

No water Thanks for the try, but I have already replaced the inlet valve. Still no water. I also checked and confirmed that I am not getting 120v to the inlet valve and/or float switch.


Check your heat dry options I have seen them short out a lot and that will prevent the water valve from getting 120v. ... Frigidaire 24 in. FDB126RB Built-in Dishwasher

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

Model # gsd3320c04bb. I am getting water to the inlet valve. I tried changing the inlet valve but still no water goes thru it. I am getting 22 V AC at the connector when operating. The only water that is circulating in the dishwasher is the water that is remaining in the pump system. Any ideas as to what is preventing the inlet valve from operating?


Sounds like you need to replace the mixing valve which is where your incoming water lines connect to the back of the washer. ... GE 24 in. GSD3320 Built-in Dishwasher

Dishwasher is not getting water. The motor runs, but there is no water going in. Was doing it once in a while, but now all the time. I ordered and replaced the water inlet solenoid / valve thinking that had to be it, but wasted $45.00...still doesn't work!


Does valve make noise . water to valve ? ck float may be stuck something under it or switch under float ... Kenmore Dishwashers

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Inlet Valve keeps stopping and starting, takes a bit of water then stops take a bit more then stops, on off on off for about 10 mins until its taken enough water to srta the cycle , have replaced the Inlet Valve still happening and water flow meter with pcb still happening Any suggestions? It a DWLT65


What about the overflow valve? It could be sticking ... Beko Dishwashers

Miele 646 sc plus inlet tank solonoid valve on water tank leaking. We moved the machine from one room to another and now this valve is squirting out water. We replaced both door seals thinking that was the problem, then started the machine with a side pannel removed, and saw the jet of water coming from the solonoid valve on the water inlet tank. Any ideas.


... Miele Dishwashers

Neff Dishwasher Hi; I have a Neff slimline Dishwasher that won't fill with water but works ok if I fill with a bucket. I have searched the net and found that it probably has either a stuck float or a faulty inlet valve. The probelm is I can't find these things. Should I pull it out and turn it upside down or what? And if I do need to replace one of these where can I get them from? I have tried a search online but can't find them.


Hallo Champer,\015\012\015\0121)Be sure water supply is arriving with enough pressure. \015\0122)If the hose between the crane and dishwasher has an aqua-stop ( or water-stop) which you recognize at the hose being enlarged twice the size close to the ... Neff 18 in. S5943 Slim-Line Built-in Dishwasher

Asko d3100 dishwasher still giving problems after replacing inlet valve. When you press the start button all of the lights come on and there is some pumping sound with a dribble of water coming through from the right hand side. When you take your finger off the start button everything stops, no lights, no pumping. Anyone got any ideas?


Hi.To start, disconnect power and ensure that there is no water in the tub when you restart the dishwasher.It looks like the overfill switch is preventing the machine from filling. The overfill (water level) switch is either a ... Dishwashers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Hi, I have a Maytag Jet Clean D/w. There doesn't seem to be any water entering the d/w when it is turned on. I have replaced the vater inlet valve and still have the same problem. Any suggestions?


If there's no water entering your dishwasher, check these: \015\012 \015\012Water-inlet valve \015\012The water-inlet valve lets water enter ... Maytag Dishwashers

Bosch dishwasher (SXH55MO6UC/46): The power comes on and runs normal, but no water is coming into the unit. I was told that it was a water inlet valve that needs to be replaced (part #263833). I need to know if this is what needs to be replaced and if so, is this something that I can do or do I need an expert repair service to do it? If it is something that I can do, I need instructions. I am handy, but this is something that I have not done before, Thank you, Craig Covey


Hi Craig,Yes it may be the fill valve...but first take off the pipe or hose and check the screen just inside the fill valve...some do not have it but most do...also check that water comes out of the hose or pipe at the valve....THEN ... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

Water inlet valve the machine wont fill with water. checked all hoses, but water inlet valve ma;y be sensitive how much are they to replace. could this be the problem?


A water valve is anywhere from 15$ to 43$ depending on make and model ... Dishwashers

The dishwasher won't fill with water. We took the water inlet valve off and cleaned the filter screen. The dishwasher worked about 2 times and started doing the same thing. We then replaced the water inlet valve and again, the dishwasher worked a couple of times and now we're back to it not filling again. What could the problem be?


Check the float assembly, that will trip and stop water from coming in. May have soap or grime holding it up. ... GE 24 in. GLD6260LSS Stainless Steel Built-in Dishwasher

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

My SHE43 Bosch DW will not pump the water out after the last cycle. The service guy said the Door latch was broken and replaced it. but the problem still exist. He now say that the water lines are freezing up because the DW is on an outside wall. The Thermador DW that was replaced never had this problem during the 15 years it was located in the same place. Could this be a bad design? Help!!!


I\015\012\015\012\015\012\015\012 the water doesn't drain from your dishwasher, check these:Drain line/air gap ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a Neff Dishwasher and I think the problem is due to the cold water inlet valve. When the dishwasher starts it drains any water and then should stat to fill. If I monitor the voltage to the valve it does switch to 240V but still fails to fill. I have verified that the cold supply works OK and the filter on the inlet is clean. The dishwasher is a NEFF GB5121 and is about 20 Years old.


... Dishwashers

The Water inlet valve # 8531325 let water run outside the dishwasher. After removing the valve I found a small ball of contamination inside and removed it. It now works with out spilling water. Do I still need a new valve?


IF the valve stops and starts water flow correctly, no you would not necessarily have to replace it. The valve should have an inlet screen to keep this from happening again.. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Hi :) We have a Bosch slimline dishwasher type SRS56A02 GB/08 - it doesn't draw in water - the timer counts down but nothing happens. We checked these pages and cleaned the filters on the inlet water line but no change :( I saw that it might be the inlet water valve - is this easy to get to - do we need to take off panels? if so, is there a manual available please? Over the past week or so it had got noiser - it was at its quietest while the water was draining out of the machine.


... Dishwashers

My dishwasher blades do not turn. I have replaced the water valve so water is getting into the unit. I have not however, cleaned out the area below the lower blade. Could this be the problem or does it sound like a motor problem? There was a bit of a burning smell up to this problem. Thanks.


... Dishwashers

My dishwasher works except is does not appear to be getting water. David psr responded: Most likely the water valve is defective or stopped up with calcium deposits. In either event, you probably need to replace the water fill valve. Not a terribly expensive nor difficult job on most dishwashers. Do I call a plumber, appliance store repair department or look for a local handy man?


I agree that the fill valve may be bad or clogged. You can fairly easily remove the valve yourself if you are somewhat handy and then take it apart and clean it. I doubt if the old valve is electrically shot but it is possible. Cleaning it out may ... GE Dishwashers

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2184 seconds