Having problems with your KitchenAid KUDC03IVWH Builtin Dishwasher ?

Brand new dishwasher, installed last week. When it is done there is quite a lot of water standing in the bottom of the tub. It has only been run 2 times since installed and both times several inches of water were left standing. Is this something we could check or do I need to have the installer come back, which will probably take a week at least. Oh-KitchenAid #KUDC031VWH


Answers :

First was a new garbage disposal also installed? There is a knockout on the garbage disposal where the drain hose connects to.
\015\012If that is not the problem make sure it has the correct high loop or also called air gap. If that is not right water can siphon back into the dishwasher. Both are common mistakes usually made by begginers. Here is a link for the correct High loop installation
Repair Help & Product Troubleshooting for KitchenAid KUDC03IVWH Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brand new dishwasher, installed last week. When it is done there is quite a lot of water standing in the bottom of the tub. It has only been run 2 times since installed and both times several inches of water were left standing. Is this something we could check or do I need to have the installer come back, which will probably take a week at least. Oh-KitchenAid #KUDC031VWH


First was a new garbage disposal also installed? There is a knockout on the garbage disposal where the drain hose connects to.\015\012If that is not the problem make sure it has the correct high loop or also called air gap. If that is not right ... KitchenAid KUDC03IVWH Builtin Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Bosch aquasensor I have just had a plumber install a second hand dishwasher as above, he left after he heard the water coming in, two mins after it stopped and nothing else happened bar the time still going, he has plumbed it into the cold water, is this correct or am I doing something wrong. Please help, thanks


No it should be plumbed into the hot side... it will not wash untill the water is hot enough ... ... Bosch 24 in. SHU43 Built-in Dishwasher

We have a brand new KUDE60FVSS dishwasher that is being installed and it is POURING water out one side of the door. The handyperson checked all the connections and we cannot figure out if it's the work or the new dishwasher. Is there some secret drainstop or something that needs to be closed?


... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

I have a G E Nautilus dishwasher that has been in storage for 2 years. Every thing works but the Drain. When the cycles are finished I' m left with a dishwasher full of water and it dont drain. I checked the bottom as u said in a previos question I see not obstacles, trash etc. How else4 can I get it to unplug? Also where can I get a owners manual? I can be contacted at [email protected] if needed. Thanks ahead of time for the help.


Hello. Here is the link to a free manual http://kitchen.manualsonline.com/manuals/mfg/ge_appliances/ge_ap ... Dishwashers

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

I installed according to guide, but dishwasher will not fill with water. Pump sounds much too loud to be normal. Wiring was checked three times for correct connections. Water supply was checked twice for water getting through, no leaks and water supply on. Drain hose is connected correctly and is connected to house drain.


You state the water supply is on.\015\012Have you loosened the compression nut at the dishwasher ell to see if you have pressure to the water inlet to the dishwasher?\015\012Remember the dishwasher will always run a little to make sure an ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Miele Dishwasher 2430 Sci. It's been not used for 5 months and when I returned it worked fine for several times (at least 6). NOW the intake/drain light keeps blinking. I have already cleaned out the drain and replaced it properly (there was nothing in there and it was clean). No water is coming into the dishwasher?however I know that the water hook-up is on (the first thing I checked). I turned the water on and off several times and AM SURE it's on now. What else could be


The usual course of events is to check and clean the filter, check and clean the water pump and well, check and clean the waste pipe and any connection to a sink or waste disposal system, then check the inlet warer pressure, then the machine level / ... Miele G2430SCi Dishwasher

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

There isabout 2 inches of water left in the bottom of the dishwasher after i run a cycle , and some food bits left in the water how do i drain the waterand remove the food bits? A manual was never left when the new machine was installed. We have a Quiet something 3 machine.


The filter is probably blocked.\015\012\015\012It is inside the base of the machine.\015\012\015\012Take out the filter and clean it and also clean out the filter well as that can also hold quite a bit of debris.\015\012\015\012 ... GE Dishwashers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

Hi I have a Bosch SGV46M13GB Classix dishwasher. Total cycle time is far greater than the displayed time and the water doesnt appear to be getting hot. I've checked the control board for any dry joints / damage etc - Nothing evident. Is there a wiring schematic available so I can check the voltage to the heater to confirm its the heater thats the problem before I purchase spares. Also, if I need to change the heater - Is there any guidance anywhere ?


First thing to do is check and make sure that it is connected to the hot water line. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Hi there, I owe A GE GSD5911D01SS Perfil Performance Quiet Power III dishwasher. The problem is that during cycle, it leaks water through the left corner, is like the water level is too high, the sensor light lit up, which doesn?t tell me much. This issue doesn?t happen all the time, yesterday was the second time and I have no idea of what it could be the problem. Can anyone help? Thank you.


... GE Dishwashers

I have a bosch dishwasher classixx its less than a year old, the 'check water' light comes on and it doesn't complete the cycle. Water is left in the bottom unable to drain away. I have checked pipes as best i could, but couldn't locate filters or remove hose from m/c. unfortunately i have no instruction manual.. help please..


If its less than a year old why dont you contact the manufacturers service team it will still be under guarantee as the bosch guarantee is 24 months you can dowload a copy of the instruction maual free of charge from the bosch or bsh home appli ... Bosch 24 in. SRS43C12 Classixx Slim-Line Free-standing Dishwasher

Moved Kenmore dishwasher to new house. Installed it. It will not start. Is there a reset switch? Model 587-1541590. Electrical installation checked OK. Water connection checked OK. Is there something I should do before I call for repair person to come


You say "electrical installation checked OK"...is the machine hard wired into a junction box or does it plug into an outlet?\015\012\015\012If in a wall socket the new house circut may be on a wall switch which is currently off. If it is ... Kenmore Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

I have a portable Sears dishwasher model # 66517769k600. It makes grinding noises when empying out the water, then stops. Sounds like maybe something is jaming the inpeller blades on the pump that removes the water as Water is left in dishwasher. It will restart in about 15 mins , run for 15 to 20 sec and stop again with same noises. What needs to be done to fix this issue? Approximate cost of part? Thanks in Advance, Chris


Hello &\015\012Welcome to FixYa\015\012\015\012It's a simple\015\012fix as the ... Dishwashers

DW fills up with water after sitting. When I turn off the water supply it does not fill up. Removed solenoid valve and cleaned the filter and check for possible blockage. Put back together and turned on water supply. did not fill up until we used it for the first time after my fix. Could the solenoid valve not be sealing off completly DW is a Bosch SH5316UC/U12


... Bosch Dishwashers

There is water leaking between the left and right seals on our Frigidaire dishwasher FBD700BFC2. The dishwasher is level and was installed by the builder two years ago. The seals are intact, and water only leaks during the wash and rinse cycles. What else should be checked or done to prevent the water from coming out of the dishwasher.


Sorry to read about your problem, I hope this helps you out.its time for new seals...I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Frigidaire FDB700BFC Built-in Dishwasher

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Holding water There is water in the bottom of the machine after the cycle is done. There is definitely draining going on throughout the cycle, but it's not draining completely at the end -and the water that is left is murky. Spoke to a friend who tells me it sounds like the dump valve, but in checking on line, that doesn't seem to be a part that even exists any more. Do I need to buy a new dishwasher? This was not in the budget this year... Thanks for any advice! Nancy


Are the dishes getting clean at the end of the cycle, if not then there could be foreign debris in the pump housing that can cause this, needs to be dismantled and cleaned out, if dishes are clean then the pump impeller will need to be replaced ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Whirlpool Dishwasher, I had a problem with the garbage disposal, so it was replaced, I hurt myself at the time and my wife had someone install the Garbage Disposal and now you run the dishwasher and no water is brought in to the dishwasher. It does drain, because I put water in and ran that part of the cycle and drained, it does turn on, it does dry but not bring in water is there something basic the guy forgot to do? Any suggestions, thank you.


He turned the hot water faucet under the sink for the dishwasher ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1457 seconds