Having problems with your KitchenAid KUDC10IXSS Builtin Dishwasher ?

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


Answers :

Repair Help & Product Troubleshooting for KitchenAid KUDC10IXSS Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

Our dishwasher is no longer cleaning dishes very well and usually the detergent tab that we put in does not dissolve completely. Our dishwasher is a General Electric Model # PDN7800G00WW and several years old. The water here is very hard. On a separate note and a new development is the control panel seems to be messing up. When we press the ''speed cycle'' which is normally 37 mins it goes to 86mins and lights up the ''speed cycle:'' button. pressing the ''glass cycle'' lights up the adjacent '


Hi,\015\012\015\012There are various reasons for the Dishwasher not cleanig the Dish properly, From your query we can understand that, it must be issue with the Dishwasher selecter switch..\015\012\015\012DISHWAHER SELEC ... GE 24 in. Profile PDW7800 Built-in Dishwasher

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the message. Push reset button and washer starts back runs a couple minutes and then stops and then beep and gives the same message on control panel "washer arm blocked" again. There is "NOTHING BLOCKING" the washer arm!


The rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so \012\012\012\012check the jets for blockages... you might have to remove the arm to clean them properly ... Dishwashers

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

Dish Washer, Model GLDL560N1055, S/NAR 808556B. Dishes and other items are not drying. They are still wet not damp. Brochure says try "Hot Start,Hot Wash or Added Heat options. Do I use Hot Start and Hot Wash at same time? Why must I use options rather then the normal control? I purchased 7 addtional GE appliances, recently, and Dish Washer only problem.


... GE Dishwashers

AFTER RUNNING MY DISH WASHER I OPENED THE DOOR THERE WAS ST HALF IN OF WATER IN THE BOTTOM SO I WAS GOING TO WASH AGAIN BUT HAD NO LIGHTS ON CONTROL PANEL HAD POWER TO THE DISH WASHER BUT NOTHING WOULD LIGHT UP? DONT HAVE 10 WASHES WITH THIS UNIT .? MODEL #655-13443K900


Hi Bennie, Try http://www.manualowl.com for free PDF for troubleshooting the issue you are having. I hope this helps. ... Kenmore Dishwashers

I have a SMEG DF612WE Type 10053 dish washer which as been standing idol for 12 months . It will allow you to change programs but when you press the play buttom for a few seconds it will not start . The dish washer was moved from one house to another but not tried before now . Please can you help


... Smeg Dishwashers

Dishes not clean after running. Dishes and glasses have a white residue on them after drying. Water is turned on and seems to ok. When I open the washer after the wash cycle starts there are several inches of water in the washer and the jets seem to be functioning. Thanks for your advise.


Hi If you are noticing that the dishes are not clean, then there are a few things to check for. Check the soap powder if it's kept in a dry environment. Also try replacing the powder with something like a gel or liqu ... Bosch SHU9925UC Built-in Dishwasher

FDBB1940DB2 dish washer controls flashing cannot reset them


... Frigidaire FDBB1940D Dishwasher

MDB6709AWW1 Poor Quality Control Panel Our dish washer is 2 years old this month and the control panel broke!!! My service technician told me that he has seen DOZENS of new Maytag dishwasher control service panels break and is convinced it is a design flaw. When I called Maytag the customer service rep had the NERVE to tell me "that because the house is near the beach, I must get a lot of power outages and power surges, that is why the control panel broke." I told her I wasn't born yesterday


... Maytag Dishwashers

We have run our dish washer several times, however, the dishes are not getting cleaned. We first ran it on "normal wash." The second and third time we ran it on "pots and pans." Not only are the dishes not getting cleaned, but the soap is hardly getting dissolved. We use liquid dish soap too. I noticed this last time, at the end of the wash, the soap was getting built up on the front-right (when facing the machine) and had turned into a solid clump; almost like plaster. I don't have a manual so


First idea goto your local home depot they make a product called AFFRESH for front load washing machines and dishwashers run this tablet inside your dishwasher with no dishes on the inside on the hotest setting this usually takes out all build up wit ... Dishwashers

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

Control panel is locked on kenmore dish washer model 176922


... Kenmore 24 in. 17692 Built-in Dishwasher

KitchenAid dish washer: Control Panel Problem


Circuit board/ Electronic control assembly needs to be replaced. ... Dishwashers

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

Dish washer 665.13592K600. Will not start. When door is closed you can hear the click of the latch then a relay on the control board. All buttons work except delay and start. You can push the cancel and drain button and the pump will activate. The start and delay buttons have no effect. Not sure if I have a control board or panel problem.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

Hi! We have a GE Profile PDW9280J0SS with electronic control malfunctions. I can't get it out of the ADDED HEAT mode and many of the other button lights won't light up. I've flipped the breaker several times, and this does (usually) reset the controls to "Normal" and "Heat Dry", but when you push "Start" it switches back to the ADDED HEAT mode. When it goes through this cycle the soap dispenser doesn't open so the dishes don't get clean. I can't use the arrows to select different types of w


Not a specific fix, but I can tell you I have this same exact model dishwasher, since 2005, and it has been services for touch pad button problems at least a dozen times. I am in fact on the phone now with service scheduling another visit because i ... Dishwashers

I purchase a house having dish washer ulra plus model no.110763691, I do not know how to swich off , because my son rotate control knob ,hot water is coming , no plate ,cup in that, how to control it please tell me


Usually the knob can be pulled out to shut the machine off. Then you can rotate it to the off position.Also opening the door will shut it off. Try these things. It does not sound like it is broken.Best, Mark ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

How to fit a control panel facia to a beko dsfn 1530w dish washer


... Beko Dishwashers

Dish washer doesn't drain, and control board only blinks


Sounds like the control board is faulty. i would suggest having a technician replace it. ... Dishwashers

Just stopped. I have an Amanna dish washer that is only 2 years old and it just stopped. It has about an inch of water in the bottom. I have power to the unit. No buttons show any lights or reaction when pressed. How do I test the latch buttons?There are 4 wires leading to the latch assembly, can I jump them to see if the latch is the problem?


Should be able to but it will run withdoor open if you do that so be careful. Have you tried holding in on the door and see if it will work? ... Dishwashers

DISH WASHER DOES NOT WORK. CLEAN LIGHT BLINKS AND THE START LIGHT BLINKS 3 TIMES WHEN YOU PRESS START, BUT DOESN'T DO ANYTHING.


... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have a KUDS02FRSSO dish washer with the normal light flashing and wont run i have read about a reset but dont know whaT BUTTONS TO PRESS


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Dish washer no power up and not sure about the board behind the control buttons, How does one go about testing it or ??


Go to bottom off unit and see if the black and white wire is burnt . make sure the power is off ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1234 seconds