Having problems with your KitchenAid KUDE60FVSS 24 in Builtin Dishwasher ?

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


Answers :

If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain.
Repair Help & Product Troubleshooting for KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

Hi...I have a Westinghouse Freestyle 921 Dishwasher...9 years young...Model SB921SG...that has recently been leaking from the bottom right hand side front corner of the door when performing its usual heavy duty cycle...It appears that the main door seal has significantly perished and is causing the problem...Therefore I have purchased a new Door Gasket part no.0208400069 from a recommended spare parts agent in Brisbane and after several attempts to re-fit this gasket/seal to the door...I still h


... Dishwashers

I have a fridigaire dishwasher PLD4555RFC0. The dishwasher now only cleans poorly if at all. The detergant used is powder and the detergant has been the same since purchasing the unit 3 years ago. The detergant does not completely dissolve on some dishes and is now staining/etching the dishes. I do not have a water softener, however, have tried the flushing with vinegar multiple times with no improvemnt. The water appears to be very hot as steam emerges when opening the door during the cycl


Sounds like your water is too hot(etching) and maybe not enough water should be about level with heater . ... Frigidaire PLD4555RFC Dishwasher

Our Kitchenaide KUDT03FTSS2 dishwasher is not cleaning the dishes like it did when it was new. It doesn't appear to dry the interior and leaves gunk inside, and is noisier than it was when we purchased about 3 years ago. It does not appear to be heating the water - we put a thermometer in there and it read 118. The water out of our tap is hotter than that. The rinse aid has been filled regularly. What should we look for?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... KitchenAid Architect® KUDT03FT 24 in Builtin Dishwasher

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

Broken dishwasher It started when my dishwasher flooded my kitchen. I drained it and turned it on, it was fine. then it happened again. I have drained it then when I went to turn it on again it just sounds like it is running with no water. If I put water into the bottom it will drain but it will not fill up. I bought this house 3 years ago I am unsure how old the dishwasher, do I need to get a new one?


I have a kenmore model 665 168 29000 the mounting bracket have broken from under the cabinet, so when you open the door and pull the racks out the machine moves forward, how can i fix this????? ... Bosch 23 in. SHU33A Built-In Dishwasher

Model no. MDB6100AWW. Just unloaded the dishwasher. Shut the door and immediately heard clicking (regular cadence). All indicator lights (arrow-shaped) for clean, dry, wash and heating delay were blinking. Opened the door, waited a few minutes, closed the door. Now, just the "Clean" and "6 Hour" arrow indicator lights and "Heated Dry" button light indicator are still blinking continuously. Cannot override. What's going on? Dishwasher came with the house when we purchased it 6 years ago. Proba


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash-heated dry ... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

How does one change the colour panels on the front of the dishwasher. Need to change panels to white with new appliances. I was informed many years ago when we purchased dishwasher that panels could be reversed to new colour.


On any dishwasher, the bottom rail can be pulled off and the panel bends and pulls right off. ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine. ... Bosch SHU5316UC Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed.


Do you have the manual?What is the exact model #?Thanks~! ... Dishwashers

We purchased an expensive top of the line Fisher and Paykel 2 dryer dishwasher when we did a total Kitchen rehaul over 1 year ago. We have been noticing water sitting in the bottom of the bottom drawer that smells like sulfur dioxide and now see water is making its way through the maple cabinet to below the sink. None of the plumbing under the sink is leaking. We also purchased a Fisher Paykel gas oven/range at the same time. We notice the oven does not appear to close completely with a tigh


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Fisher and Paykel Dishwashers

I purchased a diswasher (Hotpoint)about 1-1.5 years ago. It's model # is HDA3400G02CC and its SS# is TH887451Y. I don't think I registered it. No Matter, Two days ago, my garbage disposal stopped working. I checked the outlet. It had power. The switch to the Disposal was next to the outlet. I assumed that the switch was wired from the outlet. It wasn't. Bottom line, the switch nut was loose. I tightened it and problem solved. When I turned on the dishwasher, nothing happened. It acts like


I purchased your service (telephone support) and the dishwasher expert contacted me. We discussed the issue, he made recommendations. I followed his advise and solved the problem. Before I could recontact him, he called to follow up on my progress. ... GE Dishwashers

I have an LG dishwasher lds5811ww -- for about 1.5 years. Purchased it at Best Buy. The soap dispenser is not emptying completely anymore. The upper rack is in its uppermost position. I suspect that the top two spray bars are not turning around because they have not changed positions when I suddenly open the dishwasher while in operation. The spray nozzles do not appear clogged. Any suggestions?


If your dishwasher is cleaning poorly, check these:\015\012\015\012Water-inlet valve\015\012Internal filters\015\012Drain valve\015\012Spray arms\015\012Water temperature\015\012Detergent cup\015\012Water-inlet valve Most cleaning problems are ... LG Dishwashers

There seems to be an electrical fault in my dishwasher. It is a slimline candy dishwasher purchased only three years ago. Everytime I try to start it all the electricity goes in the downstairs of my house. I changed the fuse twice and it worked for a while only for the same thing to happen again. I also tried to turn off all other electical equipment downstairs to see if this made a difference, but it still didn't work. Would you have any idea what is wrong with it? Thanks. S. Byrne


Hello sue by rne.. \015\012If your fuse blows when you are running the dishwasher alone, I would agree that your dishwasher may have a problem however becuse you stated that it works sometimes..I am more apt to believe that when you run the di ... Dishwashers

Maytag MDBtt60awb will not start. Power definitely at dishwasher as panel lights are on, however "start" button does nothing. Dishwasher is less than 2 years old. The panel buttons eventually turn off. I've cycled the power to the unit with no response. The door is definitely latched. Unit ran fine a few days ago.


Most likely you have a bad motor when replacing the motor ihave found it is cheaper to get the pump with the motor attached where as they charge you more money for just the motor or the pump seprately try allbrands appliance parts they seem to be che ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Hello, I purchased a Kitchen Aid Architect II series KUDSO3FTPA3 ~ two years ago. It is deigned so you can put your own panel on it. Duw to a design issue with my cabinets I was not able to add my own panel and wanted to purchase the stainless panel to cover the front of the dishwasher. Kitchen aid was no help, they sold me a panel that would not fit and then would not take it back! Then they said I would need to replace the entire door for $389.00! I need to know if there is a stainless


There is a MUCH better way! go to www.applianceart.com, these guys have tons of panel options including stainless and fax stainless that was featured on HGTV and the Today Show. www.applianceart.com (Appliance Art) ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

No water goes into dishwasher. Dishwasher has only been used 2times. Came new with house 3.6 years ago. Pulled front panel off...everything appears to be connected motor fan runs.


I've experienced the same thing. Try very slowly rotating timer dial, click by click, until the water starts. Sometimes 3 or 4 clicks will start water. (You're advancing the clock.) Usually water starts in before the dial points to, "Short Wash." If ... GE Nautilus 24" Built-in Dishwasher

Have a Kenmore dishwasher #665.1677993, approx. 13 years old. Upon starting new cycle the pump turns on for a few short seconds, then off, then after a couple minutes it goes on again for a few seconds then off, then later in the cycle it does stay on for a longer period of time. In conjuntion with this intermitent problem it has begun leaking out the bottom of the front door. I have checked drain line, check valve, strainer/screen and vent in the door. I assume it is an electrical issue?


... Kenmore Dishwashers

I have a Siemens Dishwasher. I'm not sure of the model but it is built in, has concealed controls and was purchased about 6 years ago at Best Buy. It sort of looks like the SL85. When started, it runs for a few minutes and then starts to make a horrible sound. ALmost a grinding sound but may also be like water trying to get through a small opening. The sound does not stop even after turning off the DW and even the power to it. Only turning off the water supply does it stop. Help?


... Siemens SL85A705UC 24 in. Built-in Dishwasher

No power on the main switch inside the door, checked the fuse in the plug changed with new and no success, we had 2 poss 3 power cuts yesterday but the dishwasher was not working at the time? christmas time help. not sure on the actual type as it was in the integrated kitchen when we moved in 2 years ago an no manuals.


Make sure there is power coming from the house panel by checking the breaker for the dishwasher. ... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2391 seconds