Having problems with your KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher ?

I have a Kitchen Aid KUDKO1ILBS1 which is constantly blinking clean. I have replaced the circuit board once because the capacitors were bulging blown out. After replacing the board the dishwasher has a mind of its own and will start when it feels like it. Now it will not start at all. Buttons do light up when pushed but it always retruns to blinking clean. Got a solution?


Answers :

Hi
\015\012
\015\012If the clean light flashes 7 times, pauses, then repeats...

When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light flashes 7 times, all buttons are non responsive). It does this as a safety in case the element is broken and feeding electrical current into the water.

To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

If the issue returns, you could have a problem with the heating circuit (ie. element, thermostat or wiring).
It rarely happens but it could also be the door switch not engaging properly when the door is closed (slightly bend the door latch down making sure it doesn't hit the door when you close it).

\015\012
\015\012
\015\012Thanks Daniel
Repair Help & Product Troubleshooting for KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kitchen Aid KUDKO1ILBS1 which is constantly blinking clean. I have replaced the circuit board once because the capacitors were bulging blown out. After replacing the board the dishwasher has a mind of its own and will start when it feels like it. Now it will not start at all. Buttons do light up when pushed but it always retruns to blinking clean. Got a solution?


Hi\015\012 \015\012If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean ligh ... KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

Model #kudi01flbl6 flashes a 7 blink code on the clean l.e.d. won't reset via common procedures,turning on and off power. I have taken the interior apart and cleaned out many peices off glass, tooth pick and rubber bumpers off cutting boards. Would really like to know what that 7 blinks means. I can't get it to even start a cycle.


... KitchenAid Dishwashers

I have a KitchenAid drawer dishwasher model kudd01dppa and it has a mind of its own starting and stopping in the middle of the night/day and chiming all different beeps and sounds like its computer is glitching out. We had a service person out and they changed the main computer board and it seemed to fix it for a few days then started again. They gave up. They also tried some sort of reset or reboot but nothing has fixed this intermitten but long term problem. Any ideas?


"it seemed to fix it for a few days then started again" (sic) OK, well if this is so, then in my experience you are getting some, sort of Power Bourne Spike, Surge, or Transient, problem. If there is nothing else it can possibly be. Use a Pow ... Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Hobart LXi Dishwasher stops and starts in the wash cycle. Sounds like it's trying to 'start up' (like a lawn mower with a pull string). Sometimes, will run fine. Almost like a 'short' or something. Control board wash light clicks on and off. Any ideas?


... Hobart Undercounter/Lxi Warewasher 24"W x 26-3/4"D x 33-3/4"H With Detergent Pump, Hobart

Candy CDI1012 start button will not hold down, so I can't start the dishwasher. (feels like no spring in the button).


... Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers

Mbd6759aws3 just replaced the control board because multiple lights where blinking now the start light blinks and can't make it start


... Maytag Dishwashers

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

I have a maytag dishwasher model MDB7749AWB1 that suddenly won't start; i push the cycle that i want and push start and the light comes on like its going to start but then in about one second it starts blinking and the dishwasher never starts.


... Maytag Dishwashers

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

The dishwasher started making a really loud noise a few weeks ago. Then today the clean light started blinking and it wouldn't start. Fixed that w/ advice from this website and retarted the dishwasher. Now it smells like something is burning.


What your smelling? is the motor itself / bushings have worn out!! ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher is 6 years old it started making clicking and knocking sounds about a week ago. The display is blinking crazy at about 37 minutes left in washing cylce it blinks 37, HO, and CL. It blinks other numbers also. The water still seems to be flowing in and out fine. It's heating up and draining when canceled. I'm running it on normal wash and high temp. cycle. It sounds like the sensing parts in the door are going off and on.


... Frigidaire 24 in. PLDS9999CC Stainless Steel Built-in Dishwasher

Kenmore elite model 665.1669 or the 1769 model. All lights are working except for the start button light. When i hit the start button nothing happens. No blinking light, it's like it is dead. Cannot start the washer.


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Having trouble with dishwasher- I feel like dishes are not getting clean- will replacing circuit board on dishwasher help dishing become cleaner?


You may need to clean out the filters that keep food from being pumped up to spray out of the sprayers. This will depend on your make and model as to how to do this. Clogged filters will reduce the amount of water being sprayed. Try opening the do ... Maytag Dishwashers

My dishwasher starts no matter what cycle on a 2 hr hold, it doesn't hold it goes ahead with the wash cycle. And it won't shut off when the cycle is finished. Sometimes it starts like it's supposed to but most of the time it just has a mind of it's own.


... Bosch SHU5307UC Built-in Dishwasher

The dishwasher started making horrendous noises. I removed the bottom panel and narrowed the noise down to the motor (the noise starts and stops when the motor kicks on and off). How do I remove the motor to visually check it out? I thought I had all of the screws removed, but it feels like something is still holding it in place. thanks My model number is GSD4060N10SS (GE Dishwasher)


... General Electric GSD4060NSS Built-in Dishwasher

I have a Kenmore Quietguard Standard model 587 Dishwasher. It's about 3 years old. Lately, it has been running fine through the first hour and then towards the end, it will pause and the "Hi Temp" and "Heat Dry" like will start blinking at the same time. It's like it is stalled. When this happens, I open up the door and look at the bottom of the dishwasher were the screen is, and I see there is standing water. I press the "Start/Cancel" button to help it drain all the way, which it does, but th


Hi,My take on that would be a bad heating element....the dishwasher is looking for the heat from it and that never happens....so it goes no further and gives the alarm....I would get someone to check that heating element out and replace i ... Kenmore Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

I need a diagram and fixing help for a miele G892 SCU plus. The dishwasher starts up with the intake draining light blinking and the saltpc light on. Then the start stop button turn green on. It sounds like it is filling with water but a few seconds it stops and turns off. I open and no water is filling. I believe it is the water pump, what do you think? How do I install it?


... Dishwashers

I have a miele model G2470 SCVI under cabinet dishwasher it worked great until i ran out of cascade and starting using a liquid brand (Sun Light Oxi Action) we dont use the system on a regular basis so when i turned the unit on and attempted to use it , it started up filling and then sounded like it was running, the alarm tone came on with all the lights blinking a code F14 was flashing on the left side display.


... Miele Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1277 seconds