Having problems with your KitchenAid KUDS01IJ - Multiple Color Dishwasher ?

There is nothing in the coarse grind screen, but on startup there is a buzzing (wavering buzz) for about 4 minutes until the wash cycle starts. After that all is normal


Answers :

Repair Help & Product Troubleshooting for KitchenAid KUDS01IJ - Multiple Color Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There is nothing in the coarse grind screen, but on startup there is a buzzing (wavering buzz) for about 4 minutes until the wash cycle starts. After that all is normal


... KitchenAid KUDS01IJ - Multiple Color Dishwasher

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

Electronic control pad is pushed for quick wash and the LED display would show 52 minutes. Now when it pushed the display shows 17 minutes and performs all the functions that would occur at the end of a normal cycle. Can set for the longer wash cycle 94 minutes and performs all functions start to finish. Think the control board is bad any advise.


... Maytag 24 in. DWU9902 Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

It is stuck on nine minutes rinse only cycle i will start it at normal wash (2 hrs) and it reverts back to the 9 minute rinse only.. When it is running I cannot cancel the cycle


Hi mlbierman, I have the exact same problem (The 9 minute rinse). Have you been able to resolve it? Will appreciate help. My email is sanjeevnutsATyahooDOTcom ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

I have an SHU 4322. It displays "2H" in the countdown window. It will drain-cancel properly, but all of the programs display "2H" instead of the normal # of minutes for each cycle. How do I get the wash cycle to start normally?


Just reset the unit by unplugging the cord from the wall for 4 hours. The purposed for this is to drained the current stored in memory IC . So it will works normal again. Plug it again after 4 hours to see the result..Good luck: ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have a Kenmore dishwasher model # 665.13742k601, when the dishwasher is turned on to the normal wash cycle it will wash for abour 5 minutes. After the five minutes ''Delay 4'' and ''Cancel/Drain'' indicator lights will light up. What is the problem?


Kenmore has a near the same diagnosis as that of maytag when it comes to washers.you may refer to the link below.http://servicetechhelp.com/discus/messages/2801/6_917071_A_English-MD87100AWW-users-51306.pdf ... Kenmore Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

My Kenmore Ultra Wash III has a 66 min. normal cycle. Now it freezes at the 37 minute mark and just continues to wash without stopping.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

BEKO DWD 8650W DISHWASHER, AFTER HAVING GUESTS HOSE SIT FOR US WHEN ON A WASH PROGRAM (ANYONE) PARTWAY THROUGH THE CYCLE THE PROGRAM SWITCH EMITS A BUZZING NOISE FOR A PERIOD OF TIME THEN STOPS, AND CARRIES ON WASHING AS NORMAL. LAST NIGHT IT STARTED A WASH BUT STOPPED PART WAY THROUGH THE WASH AND THEN POWERED DOWN THEN BACK UP AGAIN BUT ALWAYS STUCK AT THE SAME TIME IN THE PROGRAMME, i TURNED IT OFF AND CHANGED PROGRAMMES WHERE IT EVENTUALLY MADE IT THROUGH A 30MIN WASH PROGRAMME, WITH THE BUZ


Dosent heat up or dry ... Beko Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

Cycle time Just moved in, started the Bosch dishwashe that appears to be less than two years old, left for one-hour and came back to find the wash cycle still going; hasn't cycled in thirty minutes since I've returned. Is this normal? What is the standard cycle time?


Yes its normal.bosch dishwashers use very little water and energy but,the cycles need to be longer to get the dishes clean. its perfectly OK.(ps use cascade powder if you can) ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

When I start my Zanussi built in Aquasave zt685 on a normal 65 degree wash it works for a five minutes or so and then stops. When I check, the display has changed to Rinse and Hold. Re-starting it on the quick wash program has the same effect but if I keep re-starting it eventually completes the cycle.


... Zanussi ZT485 Built-in Dishwasher

Professional series - stainless Start the cycle and it seems normal, clock ticks down but a few minutes in, it engages in the "wasH' cycle (seems to have filled some water in the tub at this point which is hot) and does nothing.... the timer just ticks away.... thoughts?


Is it please possible to provide the model number of your dishwasher.\015\012\015\012When you say water in the tub is hot, is it because the dishwasher is connected to the hot water inlet connection? Do you hear the drain pump at any time ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I am getting a clicking/ticking noise (1 click/second) from my Maytag (model MDB9100)dishwasher after it goes through its auto clean normal wash cycle. At the end of the cycle the arrow = clean and the clicking sound is there. I opened the washer door for about 1 minute noted the soap containers are empty, dishes clean, machine still hot/steamy. Closed the washer door and the clicking sound resumes. Please advise.


This is the heated dry timer going through the drying cycle until the dishes are dry. The dry cycle runs on a timer and it will click through the cycle until it finishes the amount of time preset on the timer to dry the dishes. ... Maytag MDB9100A Dishwasher

My matsui mf2w/a dishwasher sticks during cycle. normally about 10 minutes into the wash. i can move it on manually but the wash is poor. the water does not appear to be heating


Check the safety thermostat which is located at the bottom of the dishwasher. you have to remove the bottom plate,and then you will find easily the thermostat-KSD201/PF 90. you have to reset this probably.there is a red wax dot in the middle this the ... Dishwashers

When I start the dishwasher, it sounds normal. A few minutes after it starts, it makes a loud, thumping noise that lasts for several minutes. After a while, it stops making noise, but about half way through the cycle, it starts making the loud, thumping noise again. It's loud, annoying, and does not get our dishes clean. We have to wash several dishes by hand AFTER we have run the dishwasher.


I have made the assumption that your d/w is a siemens machine, however if not pls repost with the make and model.\015\012There are a few possibities...check the spray arms are clear by removing any blockages in the holes, check that there ... Dishwashers

My dishwasher is 6 years old it started making clicking and knocking sounds about a week ago. The display is blinking crazy at about 37 minutes left in washing cylce it blinks 37, HO, and CL. It blinks other numbers also. The water still seems to be flowing in and out fine. It's heating up and draining when canceled. I'm running it on normal wash and high temp. cycle. It sounds like the sensing parts in the door are going off and on.


... Frigidaire 24 in. PLDS9999CC Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1001 seconds