Having problems with your KitchenAid KUDS24SE Built-in Dishwasher ?

Removed lower spray arm of KitchenAid dishwasher and need to reinstall it. This installs over a spray arm nut that is a split ring. The nut goes over the outlet pump. I cannot get the nut to go over the outlet pump and then go inside the spray arm, which is 1/4-inch smaller in diameter.


Answers :

Repair Help & Product Troubleshooting for KitchenAid KUDS24SE Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Removed lower spray arm of KitchenAid dishwasher and need to reinstall it. This installs over a spray arm nut that is a split ring. The nut goes over the outlet pump. I cannot get the nut to go over the outlet pump and then go inside the spray arm, which is 1/4-inch smaller in diameter.


... KitchenAid KUDS24SE Built-in Dishwasher

Model PDW8200J10WW Upper spary arm not spinning, dishes in the top tray do not get clean, usually have 'grit' on them. Took spray arm out and verified no blockage in the arm itself but can find instructions to remove the bottom spray arm and pump cover to check for items in the pump intake. Any thoughts??? Thanks...


... GE Dishwashers

Kenmore dishwasher model 665.16033401 doesn't drain well. Drain pump comes on but drain water only trickels out slowly. Obstruction somewhere ? Removed rotating spray arm inside to try & get at the place where the drain water enters pump. Can't remove any parts beyond spray arm. Home: 330-865-4813 Cell: 330-608-3022


... Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

I have a whirlpool GU1200 dishwasher. There is a screen in the pump inlet which is located in a sump below the lower spray arm. It is getting plugged and needs to be cleaned, but I can't get the lower arm off. How do you remove the arm and shield to expose the screws to open the sump?


Hello....My name is Keith.....Please give me one moment while I bring up the parts drawings, and then I will start to address the issue.\015\012Thank You....\015\012 ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Kenmore BuiltIn Dishwasher Stock 17512 Model 17512200 Type 575-0 Serail FM3309375 Probelm: Water sprays out of lower arm weakly, and not out of upper arm at all. Action taken: Unscrewed the 4 screws holding down the item underneath the lower spray arm, and then the small item under that. Found major refuse from years gone by, removed, cleaned. Reassembled, same issue. I suspect I have to get 1 more level down, to the intake for the pump? found 2 screws to remove, but was not suc


... Dishwashers

Dishes not getting clean, not sure real sure if water is getting to all the dishes checked the spray arms to see if clogged but don't know how to check the pump like the manual suggest, how do I get to the pump, dishwasher is DU920PW


Try a dishwasher cleaning product. Relatively easy to check if the pump is working. Line up both the spray arms front to back and then run a sequence and see if the arms have moved. If they've moved the pump is working ... Whirlpool 24 in. DU920PW Built-In Dishwasher

Water flow in and pumping out, but not wash dishes, SPRAY ARM BLOCKED, pump not rotating and getting hot


... AEG 24 in. Favorit 80860iW Built-in Dishwasher

My Model is Kitchen Aid Dish washer KudS01DL. Water inlet and outlet are working well. I do not here the water being sprayed. Only here a straining pump. The srpay arms are barely spinning when I open the door. Water level looks OK. Is there a filter preventing the water from reaching the spray arms?


Hello,Yes their is a filter in the pump..this vodeo will show ya how to take apart the pump and clean the fitler..sorry the beginning of the video is a bit cheeesy but when they get to how to part the info is solid! ... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

Hi I've inherited a Zanussi DA6142 Dishwasher from a recent house move. It was treated quite poorly by students who I suspect ran it without the filters in place. I've used a dishwasher cleaner and was able to pull out the lower spray arm and rinse out all the crud that was blocking it (small stones, food, plastic, pieces of glass, paper, etc) but I cannot for the life of me work out how to get the upper spray arm out. The PDF manual I've downloaded for this model says DO NOT remove upper spra


... Zanussi Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

Poor washing The soap door opens but soap still in there after wash cycle. We got lower spray arm off and one plastic piece but can't get all the way to the pump. Pump appears to possibly be cracked so we suspect it needs replacing, but we can't get it out.


Before you suspect the pump and motor assy, do you hang the silverware basket on the front side of the lower rack or if not did one of the holders for the rack fall off and you replaced it? I have found that id the basket is hung on the rack that tal ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

I have a Maytag MDB dishwasher. We recently took apart the spray arm assembly down to the filter to clean out the lime. The problem is that the inside of the spray arm has such a build up of lime and we cannot get inside the narrow space to scrape the lime out. How can I dissolve the lime that is inside of parts?


Have you tried boiling it in vinegar? it might help. no garenties for that particular problem, but that's what I do with my kettle and chunks of lime come out when I do. ... Maytag MDB9600A Jetclean II Built-in Dishwasher

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

Miele g660 dishwasher upper spray arm fallen off, broken ring.. Do I buy retaining nut... Which looks ok to me or arm... Which also looks fine! Where do I get the thing that holds the arm up onto the


... Miele Dishwashers

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

I have a Kenmore dishwasher model #665.13842K601. The problem that it has is that it does not seem to be pumping the water around the tub after it fills. It will fill and drain fine but will not wash. I have removed the spray arms and checked all the parts that I can get to from the inside but fear that it may be a pump or jammed impeller. it does make a faint buzzing sound when it should be operating. Any input would be great. Thanks, Matt


It sounds like you have a circulation problem which means that the circulation pump has gone bad. \015\012Circulation pump - http://www.appl ... Kenmore Dishwashers

It is not pumping water into the spray arm to wash the dishes. I can get it to fill with water and drain the water, but when it fills and the cycle timer starts, nothing happens, and a slight burning smell occurs. Does this model have a reversable pump or a direct drive? I am thinking this is where i need to start.


... Kenmore 24 in. 16533 Stainless Steel Built-in Dishwasher

I have a whirpool Quiet Partner III, and the top layer of glasses is not getting clean. I had a technichian out some time ago, and the problrem was caused by food debris trppaed in the filter in the wash module. He saud it was easy to clean that out, so I have removed the lower spray arm, but cannot undo the 4th screw that will allow me to take the grey round filter cover off to remove the food or paper debris. It is under the white flat pipe that delivers water to the wash module, and I cannot


I had same problem, would not clean well and fixed it. . I cracked open the door during wash cycle and used screwdriver to defeat the door lockout. The water from the bottom sprayer was only shooting half way to the top of dishwasher. To fix I remove ... Whirlpool Dishwashers

We took off the spraying arm to clean it out and now we cannot get it to stay on. The tab in the center will not hold the arm.


Hi,\012That\012is not that hard to fix and you can easily buy the parts yourself\012online...Here is a tip that will help you with the online\012buying...How to Buy ... Dishwashers

Water is not being sprayed by the spray arms. Maybe the pumpis clogged or the motor is defected How do i get at the pump?


... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

I have a Whirlpool GU2500XTPQ3 dishwasher that is about 5 years old. The dishes in the top basket do not get clean. I checked the water tube that feeds the upper spray arm and the top spray and there aren't any obstructions. Our water pressure and temperature are suitable. Could the pump be plugged or otherwise lose its ability to circulate enough water to adequately feed the upper sprayers? How can I check on that?


Hello,\015\012\015\012Welcome to FixYa,\015\012\015\012Based on your description as well as all you`ve done on your own I`d suspect you`re on the right track with the plugged pump suspicion.\015\012\015\012The plac ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

GE Quietpower 2 spray arms not rotating. Sounds like pump is working and water is moving inside but arms are still in same position when I check to see if they've moved. Of course the dishes don't get clean. What's up with this?


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

Cannot remove "base spray arm"


It should pop on and off ... GE Hotpoint HDA3500N Dishwasher

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1314 seconds