Having problems with your Kohler NET HP COURAGE XT-7 SERIES VERTICAL ENGINE ?

No spark at plug - Kohler small engine - Kohler NET HP COURAGE XT-7 SERIES VERTICAL ENGINE


Answers :

Repair Help & Product Troubleshooting for Kohler NET HP COURAGE XT-7 SERIES VERTICAL ENGINE

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No spark at plug - Kohler small engine - Kohler NET HP COURAGE XT-7 SERIES VERTICAL ENGINE


... Kohler NET HP COURAGE XT-7 SERIES VERTICAL ENGINE

Engine lockup I have a craftsman power washer with a briggs and stratton 850 series engine, craftsman model 580752220, the engine will not turnover unless i remove the spark plug, it has electric start and will turn over with no problem like this but if i put my finger over the plug hole it locks up immediatly


Sounds like the intake or exhaust valve is not opening. ... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Spark plug gap on my kohler cv-15 engine - Kohler 18 Hp OHV V-Twin Command Engine


... Kohler 18 Hp OHV V-Twin Command Engine

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

11 hp honda pressure washer engine won't start. No spark at the pkug, bought a new coil and still no spark. This sysem only has a coil off the fly wheel and the spark plug. I even changed spark plug. Use the unit the other day, shut it down and on restart it won't start. Also, I disconnected the kill switch and the il lvel sensor so nothing was going to ground.


If you replaced the coil,check the wire and boot,check with meter for continuity.could be loose connection to spark plug ... Honda Pressure Washer PSI 3000

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

Have a genarac pressure washer when trying to start the engine catches half way through the pull with spark plug out it cranks fine


... Briggs & Stratton Power Products 1539 Pressure Washer

Crafstman 22hp briggs and straton engine, I've changed spark plugs, air filter...when engine runs it does so unevenly and at times backfires. What can I do to solve the problem?


Don't use the choke, turn the lean all the way to the right and back off 1 and a half turn, its running too rich, usually find this screw under bowl on carb, don't mess with the other screws, take air breather off and let breath without choking, if y ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

I have an Excell VR2500 pressure washer with B & S 6.5 HP engine. It was running fine, but then stalled out and now will not start. Has clean gas and full oil. I pulled the spark plug it is producing a sufficient spark when starter cord is pulled. Any ideas what might be causing the problem? Please help.


The key things to check are the spark plug, the air filter, the fuel. If those are all new and in good shape then you probably have gum in the carburator. Get a can of starter fluid and a helper. One person squirt the starter fluid into the air in ... Briggs & Stratton Pressure Washers

Magneto on pump engine is not sparking plug - Honda 8 HP Engine


Has it got plenty of oil ?un plug the low oil senser wire as they do give abit of trouble and tryit then ,if still no spark you may have to lift the fly wheek and get the ignition module checked "youdoit" ... Honda 8 HP Engine

I have a mid 60's 6 hp Tecumseh engine on a Troybilt tiller. I used it to till my front yard and it ran fine. I let a friend use and it quit on him after a few minutes. It will not start. It has spark at the spark plug. I have thoroughly cleaned the carburetor by taking it apart, soaking it in cleaner, blowing out all holes and passages. I made sure the tiny holes in the power valve at the bottom of the fuel bowl are open. I have taken this carburetor apart five or six times over the years an


... Karcher 2500 PSI Pressure Washer

Hello i have a Honda GX160 and the engine will only run on choke if i close it the engine just splutters and thats it. it wont run at the norm i have replaced the carb the tank the air filter and the spark plug and know luck i have no more ideas as to what the problem really is thanks jord


Ii know you must have replaced the fuel filter. Did you replace the fuel line? It is obvious it is not betting enough fuel or it is out of time. Have you tried adjusting the jets on the carb? Have you checked the timing? There is a crankshaft key-way ... Honda Pressure Washer PSI 3000

I have a Baldor 6000W generator with a gx340 11hp engine. I have drained the tank and carb and put new gas and sea foam in it. Also I have replaced the spark plug and fuel filter. The engine will start/run as long a I spray starting fluid in the carb. But it will not continue to run without it. Also I just checked the oil level and that is good. Please help!!!


It sounds like the engine is not getting enough fuel for it to run. First check that you have the fuel tap in the on position. If the fuel tap is on then the carby might be blocked or the needle & seat are not working properly. Turn the ... Honda 8 HP Engine

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

675 series spark plug gap settings


... Karcher Pressure Washers

Kohler command 20 twin engine - no spark


If there's no spark, then either the spark plug has come into contact with gas, or the ignition coil is bad. Try either replacing the spark plugs, or removing the old ones and seeing if the tips are damp.If replacing them doesn't work or the ... Kohler 20 Hp OHV Command V-Twin Engine Exmark Navigator-ZTR-Comm.R

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Troy bilt power washer 6.5 hps briggsstratton engine. Put new spark plugs and new gas ,wont crank


... Pressure Washers

Engine starts, but when i push in the choke, it kills. i just replaced the spark plug, drained the gas and oil and replace with new gas and oil. Starts fine when choked, but when i push in the choke, it dies.


... Honda 50 W Ar Pump 2500 Psi 25 Gpm Pressure Washer

Honda GX340 engine will start, but will not continue to run. Checked fuel and spark plug.


... Honda Pressure Washers

Honda GX340 engine will start, but will not continue to run. Checked fuel and spark plug.


... Honda 8 HP Engine

I have a 2500 craftsman power washer with a Briggs and Stratton engine. I used it about a month ago and it worked fine. Took it out yesterday and I could not pull the rope to get it started. I took out the spark plug to release the compression but I still could not pull the rope out it is locked any advice.


It sounds like the pump is seized. Make sure any pressure has been released by pulling the trigger on the gun. Sometimes this will allow you pull the cord. If the pump is seized, a new pump would be in order. ... Briggs & Stratton Pressure Washers

Carb hunts at wot and at idle, it will backfire if your not running the trigger. exhaust pipe turns red. seems to be lean. carb is clean with a new kit, fresh gas, and spark plug. if i add some choke it runs better. all the jets are clean. carb was disassembled and soaked in engine tuner.


It sounds like it is running really hot. Did you check the air filter and oil level. If not these it could be the muffler. ... Porter Cable Pressure Washers

Engine does not start. I ran it about two weeks ago and it worked fine. I took the spark plug out and it was dry. I made sure there was gas in it. I tried some starting fluid by spraying into air intake and it start running for a short time until the starting fluid ran out. I removed the carb bowl and there was gas in it. However the inside of the bowl and the float had brown deposits and looks like rust. So I think the main jet has been clogged up with a particle. How do I clear it? Where do I


Try cleaning the carb with gumout spray and a little compressed air, be careful to reassemble the float and needle valve exactly as you found it. ... Northstar Pressure Washer 3000 PSI
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0743 seconds