Having problems with your LG 24" Built-In Dishwasher - Black ?

My dishwasher is showing LE on the display and will run but doesn't seem to be cleaning the dishes. Any solutions?


Answers :

Hi there,\012

Well LE means locked motor, this seems to be a very common problem withe these dishwashers.

Possible Cause For Error Occurrence:
Wiring connection is OK?
The Impeller of Washing Pump is locked.
The rotor of Washing Motor is locked.
The Blade is locked.

Anyway the LE error code is not all-ways indicative of a motor problem. There are also strong chances of any lose connection (wire), so first you can simply unscrew the front door panel from the retaining screws on the inside of the perimeter of the door. Once the screws are removed pull down and out to remove the door panel. Remove the sound insulating material and you will see several wires routed from the contol panel the length of the door to underneath the unit. Inspect the wires thoroughly. Near the bottom is where the pinching can take place. There are two gray wires and if you have been getting the "LE" error code, one of those wires is most likely broken or pinched. Splice, reconnect, solder or tape.......

Please follow the below link for more information (the link contain service manual, you can check the page number 25) -

http://136.166.4.200/contents/Dishwasher/LDS5811/LDS5811_Service_Manual.pdf

(Just copy and past the above link in your web browser)

Good Luck!!

Thanks
Repair Help & Product Troubleshooting for LG 24" Built-In Dishwasher - Black

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher is showing LE on the display and will run but doesn't seem to be cleaning the dishes. Any solutions?


Hi there,\012Well LE means locked motor, this seems to be a very common problem withe these dishwashers.Possible Cause For Error Occurrence:Wiring connection is OK?The Impeller of Washing Pump is locked.The r ... LG 24" Built-In Dishwasher - Black

I have a Frigidaire fdb710lcs0 that never seems to complete a cycle, runs continous, leaves a white cloudy film on the plastic dishes, soap residue on the other dishes, and has a stinky smell now. I first noticed this when I turned the thing on efore leaving for work, came home & it was still running. I have recently wiped "crud" from the bottom inside of the unit where it meets the seal. Although I have read other posts about people cleaning the filter or running a vinegar solution, I don't kn


... Frigidaire Dishwashers

My Thermador DWHD64CP/31 dishwasher always has an Asterix on the display panel, runs for a long time, seems to only pre-wash the dishes, sometimes does not dispense the cleaning agent, and there is no


... Thermador 24 in. DWHD64CP Stainless Steel Built-in Dishwasher

Have SHU43C and have had no problems with it. We usually run it on the Quick Wash cycle, but ran it on the Regular Wash cycle yesterday because the glasses seemed to be coming out spotty. After it ran, there were no lights on the display like there usually are. The washer had run and the dishes were clean, but it has not drained completely. There is still about an inch of water in the bottom, despite removing and checking both the Large Object Trap and Fine Filter (neither which were clogged


The drain pump needs to be replaced or cleared of obstruction. ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

My Maytag Quiet Series 100 is leaving a white residue on dishes and glasses. The problem seems to be getting worse. I have used multiple dishwasher cleaning solutions, with no resolution to the problem. My glasses have what seems to be permanent white residue on them and the plates are now showing the same residue. What can I do to solve the problem?


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Maytag 24 in. MDB5651A Built-in Dishwasher

6th sense whirlpool dishwasher not heating water or finishing cycle showing f3 on display dishes seem clean but not spotless and wet becuase they are cold


Check thermostat and heating elementwires and timer ... Dishwashers

Bosch SGI4345AU/17 shows 2H on the display, it does not seem to matter which program is selected, the unit runs continually. It does not heat the water or finish any cycle. The washing tablet covers the dishes and is not rinsed off. Any thoughts


The Control unit on your Bosch has a burnt out heat circuit. Just about every dishwasher has a number of "thermal holds" during the wash and rinse cycles in which the controller waits for the water to be heated to a specific temperature ... Bosch Dishwashers

My Quiet Partner 11 cleans and operates well but it never seems to dry the dishes completely especially the silverware. I normally run on Light or Normal cycles. Any solutions will be appreciated.


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The Heating Element not Working ... Dishwashers

Hey all, my dishlex dx302 wont heat the water thereforgiving a **** clean. Have searched this topic for a solution and after removing circuit board from front door i found that the board doesnt seem to have dried out like the pics show in some instance any other ideas


Hi,Check your heating element.. Dishwasher ... Dishwashers

Our 16 year old dishwasher takes way longer to finish cycles, has become very loud and now no longer cleans the dishes - especially the top rack and the silverware. We have hard water and I have run it with vinegar in a bowl 3 times and have been cleaning all the deposits I can today. It doesn't seem to be draining out all the gunk. Water flow seems ok, the arms have nothing blocking them. Any instructions for me to follow to clean out the mechanisms? Or has it run its lifespan... Thanks!


Parts are no longer available for your dishwasher. Typically - manufactures end support after 10 years.Your hard water deposits will never come all the way out. They will be "clean" for a month or so until another calcium chunk breaks free and ... Dishwashers

Doesnt clean dishes, seems to be no water coming into machine


There should be about 2 inches of water in the bottom of the DW.  If it is filling but not washing the pump may be bad.  That might explain the loud noise (motor bearing).  I assume that the detergent cover is opening but no water is b ... Dishwashers

Our whirpool dishwasher seems to be cleaning the dishes here and there, missing some. The top shelf of the dishwasher does not seem to be cleaning at all. Also the soap dispenser does not seem to be quite empty of soap when the cleaning cycle is done. It is running fine. Could it have something to do with the panel where all the buttons are? Could the sequence be off or something? Thank you Awaiting your reply


This sounds more like the sprayer arm isn't rotating freely.Open the dishwasher and pull the bottom tray forward (remove it if you like)Reach in and try to rotate the sprayer arm. It should move freely. If you give it a quick flic ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher is not cleaning dishes - it is running through its cycles, but when it is done, there is a heavy residue of soap and hard water and the dishes looks worse than when i put them in.I've changed dishwashing liquids and even replaced the extra cleaning solution (little hanging basket) with a new one, and still not washing dishes clean. this is a kenmore and is about 5 years old.


Hello there:There are 6 areas that could cause this to happen Please follow these simple steps okInvestigate each of these six areas if your dishwasher is not completely cleaning your dishes:\015\012\015\012 \015\012\015\012\015\01 ... Kenmore 15899 Built-in Dishwasher

There are no error codes showing, water is definately getting hot but dishes on bottom tray not cleaning, i have used few products specially designed to clean the dishwasher itself without any dishes in, checked the filter, salt, etc, used tablets, gels ... nothing seems to work. Dishes just not clean !


Lower washer not working but upper washer is. This is due to the dishwasher thinking it is on half load. the sensor is faulty and you need to replace the whole unit (water circulation pump). However if like me and your not bothered about having a hal ... Baumatic 23 in. BDW13 Built-in Dishwasher

Dishwashing liquid ( Cascade Liquid- gel- with Dawn) seems to be crytalizing is dishwashing reservoir on the door. After running the dishwasher the small door holding the liquid is open but still has some residual dishwashing liquid in and it seems to harden right away into a crytal like substance. Just started doing this. Is it the product or dishwasher? The dishes come out clean. This product doen't seem to clean as good as the first cascade. Thank you


Tide is having a problem with it freezing during shipping. Call for a free replacement. Or...to thaw it she said to put it in hot water in a sink for one hour, then do it again (not boiling...have lid on tight). ... Whirlpool Dishwashers

My dishes have a film and sometimes have mould on them after they've been run through the wash cycle. All my dishes are practically clean when the dishwasher is run and we open the door as soon as the cycle is done. Anyone have any solutions? Is it safe to run an empty wash cycle with bleach instead of dishwasher detergent?


Try using some orange tang drink crystals...sounds odd but works really well.. your dish washer will look like new inside ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

My Kudi01iLBL dishwasher is not cleaning the dishes. It seems to run ok through the cycles and there is plenty of water but the lower dishes are not very clean. The silverware never gets clean. What can I do?


Hi\015\012\015\012Thanks for using FixYa. To\015\012start with check the water inlet valve and try to clean its inlet screen as\015\012that might be clogged. If this is fine then check the spray arm and clean its\015 ... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Hi - I have tried all the usual tricks of running an empty load with vinegar, and the food particle filter seems to be the kind that isn't removable. Whenever I run a load, there is enough left over particles on the dishes - especially the top shelf, that I either have to wash all the glasses by hand, or run at least one more cycle. I have a standard size hotpoint built-in dishwasher. Please let me know if there is a way to clean the filter, or an alternative method so that the dishes are a


The best but not the fastest way is to remove the pump and motor assy and visuall inspect for fooreign items in the pump assy and also inspect for damage to the pump inpeller at the same time. Sorry not a fast fix but the best way ... Dishwashers

Bosch Diswasher Have Bocsh SMU 2046 UC diswasher. Aprox. 11 years old Has always worked well. Recwntly is not cleaning at 100% as before. Seems to run through cycle as normal and sort of cleans but leaves stains in coffee cups and flatware seems filmy, sometimes a little guk left on dishes, all uncharacteristic of past performance. Tried a thermometer during cycle and water temp is around 151 F during wash, 136 F at rince. and 154 F at dry time. Have checked arms for cloging and are free w


Remove the drain hose and check if you have any residual into it. After 11 years your appliance may need a thourought cleaning.Check also if the pump has enough pressure. ... Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Dishes not clean after running. Dishes and glasses have a white residue on them after drying. Water is turned on and seems to ok. When I open the washer after the wash cycle starts there are several inches of water in the washer and the jets seem to be functioning. Thanks for your advise.


Hi If you are noticing that the dishes are not clean, then there are a few things to check for. Check the soap powder if it's kept in a dry environment. Also try replacing the powder with something like a gel or liqu ... Bosch SHU9925UC Built-in Dishwasher

Drawers Stuck I've had my dishwasher for a couple of years now. All of the sudden the drawers are extremely difficult to open. I have to use all my strength to pry open the drawers so I can get the dishes out.  It started out as only the bottom drawer having the problem and now both drawers are having it.  It seems to be running fine because the dishes that were in the drawer before it got stuck were cleaned.  And there is nothing blocking the drawer from opening.  It seems like the seal that c


I turned off the electrical breaker for about 8 seconds and it rebooted itself ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Dishwasher is not drying. At end of cycle, dishes are still wet and damp, as well as the inside. Buttons are all pushed. Also, it seems to wash for more than one cycle. Did a light wash and after 1-1/2 hrs., it was still running. Purchased a couple of months ago. Dishes don't seem to be as clean as my old dishwasher.


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Whirlpool MDBH969AWB Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1188 seconds