Having problems with your LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher ?

I have LG-12AW2 Dishwasher, it starts for 20 seconds and it stops and the light flashing and for about 10 minute later it gives a code IE what that mean and how to fix it


Answers :

Hi
\015\012
\015\012The code IE means its a Water inlet trouble. You need to check clogging of water inlet hose (or hose twist or freezing) and also check water supply. If there is clogging you need to clean it so that the issue is resolved.
\015\012
\015\012Please do accept the solution if the issue is resolved or else revert for further assistance.
\015\012
Thanks
Rylee
\015\012
IE is inlet error, displayed when "Not reached to the normal water level in spite of 10 min. water supply"
\015\012\015\012
\015\012\015\012Possible cause:
\015\012\015\012
\015\012\015\012
    \015\012
  • The Water Supply Tap is closed.
  • \015\012
  • The Water Supply is shut off.
  • \015\012
  • The Inlet Hose is kinked.
  • \015\012
  • The Water Pressure is very low.(below 10 psi)
  • \015\012
  • Inlet Valve is OK?
  • \015\012
  • The filter of Inlet Valve is clogged by impure water.
  • \015\012
  • The Hall sensor is OK?
  • \015\012
  • The Impeller of Air Guide is bound.
\015\012\015\012Remedy:
\015\012\015\012
\015\012\015\012
    \015\012
  • Cut power by tripping circuit breaker or unplugging power cable for ten minutes.
    \015\012
  • \015\012
  • Take action on Water Supply device.
  • \015\012
  • Measure the electric resistance of Inlet Valve. (950-1300 )
  • \015\012
  • Clean the filter of Inlet Valve.
  • \015\012
  • Check the frequency of Inlet Water by the Test Mode.
  • \015\012
  • Replace the Air Breaker
Let me know how this turns out.


Benjamin
Repair Help & Product Troubleshooting for LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have LG-12AW2 Dishwasher, it starts for 20 seconds and it stops and the light flashing and for about 10 minute later it gives a code IE what that mean and how to fix it


Hi\015\012\015\012The code IE means its a Water inlet trouble. You need to check clogging of water inlet hose (or hose twist or freezing) and also check water supply. If there is clogging you need to clean it so that the issue is resolved ... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Hi I have an F&P DW691 dishwasher (manufactured by whirlpool) the reser light is permanently giving two quick sucessive flashes and will not start the machine unless held on for 6 seconds, the machine then starts for a minute then stops and goes back to the two flash reset problem. Does any one know the fault code applications for this model.thanks Mike


Hi, I've got the same dishwasher but with a different fault, there's power down the cable to the d/w but no power lights on the front panel?Thanks. ... Fisher and Paykel Dishwashers

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Overfill Hi Mark ,my Hotpoint BFI 62 at very first use ,takes water but in few minutes later water come out from floor and after that you can hear water drains out,Heavy Duty cycle light flashing rapidly,after some advice looked exactly source of water is from pipe connected to overflow system. That mean it is filling more than required,how it possible new Dishwasher never used before? Please help me to repair because we never try when I bought now is to late for company warranty. [email protected]


... Hotpoint 23 in. BFI62 Built-in Dishwasher

The dishwasher is flashing error 20. The wash cycle begins to work but after a few minutes the wash cycle will stop and the light flashes on the program selected. We have tried turning the dishwasher off from the switch to no avail. Please advise us on what we can do to fix this.


... AEG 24 in. Favorit 3A Free-standing Dishwasher

Frigidaire PLD4375RFC Dishwasher Dishwasher. Error code PF keeps flashing. I can open and close the door, it goes off. A litle later it starts flashing again. PF, means power failure


... Frigidaire PLD4375RFC Dishwasher

At 2 minutes left in the wash cycle, the quick rinse light starts blinking and the timer goes to 0. My dishwasher is a Whirlpool Quiet Partner IV gu1500xtkbo dishwasher. I'm assuming the blinking light is an error code. What does it mean?


... Whirlpool Dishwashers

My indesit IDL 500 dishwasher has two warning lights flashing (nos 2 & 4) but the manual gives no indication of what this means. Apart from the lights the machine appears to be functioning normally. Any ideas what this means?


... Indesit Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.


... Smeg Dishwashers

Hi, I have a whirlpool ADG 7340 dishwasher and it's failing to run a full cycle (it just starts beeping constantly about half way through). The light is flashing 4 times so I guess that means it's fault number 4 but I have no idea what fault 4 means & how it would need to be fixed.


... Whirlpool Dishwashers

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

Kenmore Elite 665.7696 dishwasher - "normal wash", "pots pans" and "cancel drain" lights flash on control panel. If power shut off for some time will work for part of load then start flashing again and stop. Is this a trouble code? If so, what does it mean?


Hi\015\012\015\012This error code appears when either the keypad(Part#1 in below link) or Control board(part#11 in below link) is faulty. You can reset the error codes sometimes by turning Off/On the power, however, this is not a permanen ... Kenmore Dishwashers

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).To resolve this you will have to reset the console. Do this by closing ... Whirlpool GU2400XTP Built-in Dishwasher

Hi, I Have a whirlpool dishwasher ADP 6515 and working fine for the past three years. Just last night, the dishwasher started initially but then stopped as water not draining. Flashing green light. Not sure what it means. Could you please help and tell me how to fix it.


... Dishwashers

My frigidaire dishwasher PLD2855RFC0 intermittently either stops during the cycle or ends the cycle with the code PF flashing in the timer window along with the "High temp wash" and "No heat dry lights" flashing. What does this indicate and what is the fix?


... Frigidaire Dishwashers

Have a frigidaire dishwasher (model- PLD4375RFC0)about 2 years old. Set to run as we left to go out of town- when we came back all lights flashing including error- found a child's plastic bowl that had fallen to the bottom and had a melted spot as it was next to the heating element. Called support and were told to master restart- shut the power off for 15 minutes. Did and now flashing "27". Cannot find a code for that and neither could support without sending out a repairman. Any advice before


... Frigidaire Dishwashers

Hi, i have a hotpoint slimline SDW60 dishwasher that has 2 lights flashing. the fast and delicate lights which means an error but what error and can i fix it myself, can anyone tell me please?


Download the user guide here >> http://kitchen.manualsonline.com/manuals/mfg/hotpoint/hotpoint_dishwasher_product_list.html ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


Do a "key dance" between normal and heated dry , going bak and forth six times. this will rester the heater fault. That is the clean light flashing code. Now you have to find the cause. Most likely is that there were suds in the last cycle or the do ... Dishwashers

2006 kenmore elite dishwasher 665-17263402- the clean light flashes 7 times , pauses then flashes again 7 times. What does that code mean? Cannot get washer to operate.


The blinking "clean light" is a common problem with some of the Kenmore and Whirlpool models dishwashers. The problem is usually attributed to water supply temperatures being too low when filling. Apparently, there are some issues with th ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Got a Miele G2220sci dishwasher unit, getting an undocumented error code of F19 with flashing lights, help! what does F19 mean?


Miele tech's say this is a "Flow Meter" problem, which could involve their service department. ... Dishwashers

Got a Miele G2220sci dishwasher unit, getting an undocumented error code of F19 with flashing lights, help! what does F19 mean? WONT DRAIN. PROGRAM FINISHES WITH F11


F19 is water in the cabinet takes too long to heat up. you can reset the heater limiter..\015\012\015\012Reset the error message as follows: To cancel the error message, turn the rotary selector switch to "Stop/End" or press the "Start/St ... Dishwashers

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

My dishwasher is beeping and giving an F13 and F14 code. Would like to know what it means and how to fix it.


Mee too ... Miele G 1470 SCVi Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2782 seconds