Having problems with your LG 24 in. LD-12BW5 Free-standing Dishwasher ?

Error le STARTS AND RUNS STOPS ERROR CODE LE WATER DOES NOT DRAIN OUT


Answers :

Hi
\015\012
\015\012Error Code LE is a Motor Error

Possible Cause For Error Occurrence:

Wiring connection is OK?
The Impeller of Washing Pump is
locked.
The rotor of Washing Motor is
locked.
The Blade is locked.


Remedy:

Check the wiring connection.
Replace the cause of restriction.
Replace the Washing Motor.
Replace the PCB.
\015\012
\015\012
\015\012Please do rate the solution as "FixYa" and revert for further assistance.
\015\012
\015\012Thanks
\015\012Rylee
Repair Help & Product Troubleshooting for LG 24 in. LD-12BW5 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Error le STARTS AND RUNS STOPS ERROR CODE LE WATER DOES NOT DRAIN OUT


Hi\015\012\015\012Error Code LE is a Motor ErrorPossible Cause For Error Occurrence:Wiring connection is OK?The Impeller of Washing Pump islocked.The rotor of Washing Motor islocked. ... LG 24 in. LD-12BW5 Free-standing Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Smeg DF612S All starts well but after 40 minutes stops with a beep and will not progress to the main wash cycle. Instead all programme lights come on (located on the left), along with the first 2 phase lights (the first two of the lights on the right hand panel). This indicates error code 3 (cannot pump out water), but water is entering and draining perfectly. Please advise.


Check to make sure there r no kinks’ in the drain line or\015\012that it is not clogged it sounds like the sensor is tripping because there is\015\012too much strain on the pump just like a breaker. ... Smeg 24 in. DWI612 Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

I have a Bosch SHU66C02. I opened the door to stop it from running temporarily, while it was sitting not running, it leaked all of the water out of the bottom right corner of the door, and when I went to start it later it just hummed but the timer didn't go down for over an hour. I tried to put more water in but as soon as I started I could hear the water added to drain. I turned the breaker in the fuze box off to it and let it sit for over an hour, but when I restarted, the timer was still at


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

My asko d3250 thinks the drain hose is blocked. but when i pour water in the dishwasher to see if the water is being drained, the dishwasher is draining properly. Yet the dishwasher after it has drained the water, will shutoff and start flashing the Large Pot icon (drain hose is blocked error code). Is there a sensor that is faulty?


Yes, it sounds like it is to me. I'm not able to pull your model up on my data base,if I could I would be able to tell you where it is located. I would assume that it's located either inside the pump or close to it. Sorry I couldn't be more help. ... Asko Dishwashers

It starts running then stops - starts pumping in water then stops, etc. burning plastic smell near top... doesn't leak, gets power, but begins to fill, then stops - might start to drain (pump), but then that stops too...


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

Frigidaire dishwasher shows an error code of ER uo after only a small bit of water runs into the dishwasher shortly after the hot water starts running into the dishwasher upon starting the dishwasher up.


... Frigidaire Dishwashers

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

ETNA ENF 18500A/5 type: 3.E1.181213221110 36 VLENNL 5 Dishwasher lights are on, and set for running, but the dishwasher does not do anything. Sometimes it makes a slight hum when closing the door, but most of the time, nothing. It stopped running after standard dish washing liquid was put into the machine by mistake. At that time, the machine started and ran through part of the cycle, but did not complete, and did not drain the water. Since then it has not started again. I have remo


... Dishwashers

Dishwasher works fine except that after the drying cycle, water slowly builds up in the bottom of the dishwasher. It did this a few years ago for several months, but then it stopped doing it altogether. I did nothing to fix it. Now it's started doing it again. I run the dial around to a point where it drains, let the water drain and then turn it back to off before the drying cycle begins.


Hello,\015\012\015\012This would mean that the dishwashers water valve has failed. This is a simple repair to make yourself. The lower access panel would need to be removed, four screws. You can purchase the part from the link below.\015\012 ... GE Dishwashers

Bosch auto 3 in 1 dishwasher not running full cycle. When the programme starts, water starts to fill then stops and water drains as the timer goes back to 0.


... Bosch Dishwashers

Dishwasher not draining E25 error code (Bosch exxcel) . I have cleaned filters & removed pump inspection cover to check / clean debris I have also checked the waste water pipe is not kinked, it runs for 1hr 15 mins last time and then cut out with the error code displayed.


Gr8 stuff klaudi & Nypmh - rocking it back 45% worked a treat. Bloody BonzaShell XX ... Bosch Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2020 seconds