Having problems with your LG 24 in. LD-12BW5 Free-standing Dishwasher ?

E1 Error Message

\015 I have just replaced the water inley valve on my LG LD-14AW2, however after filling with water message E1 error comes up suggesting water damage. No visible leaks or damage. Any clues.\015

Answers :

Yep, impeller motor problem.... mines done it twice now. Absolute piece of **** dishwasher. I HATE IT!
Agreed all LG d/w with E1 is the wash motor faulty.
\015\012
\015\012take care.
Repair Help & Product Troubleshooting for LG 24 in. LD-12BW5 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

I have had an E24 error message on my Siemens freestanding dishwasher. As well as the Error message the the little tap sign lights up too. Up until now the problem has occurred around 1 in 3 attempts and mainly at night but not in the day. When it does work the washer works perfectly and washes well. Today it will not work at all. The error always comes up 2 minutes into any cycle. I've tried turning the water feed off and on and in the past this has worked. It sounds like no water is gettin


Hi Steve\015\012\015\012E24 error normally indicates failure to drain, the first\015\012thing to check is that the water is actually being supplied to the appliance\015\012and is turned on. If it is then check the water inlet valve, if th ... Siemens 24 in. SE25T250 Free-Standing Dishwasher

Zanussi ZDF 511 S dishwasher not draining. Shows error message '20'. Cleared filter, removed hose from usual drain and restarted cycle. Still not working - same error message. Any suggestions would be helpful. Thank you. Myles


... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Our 2 drawer Fisher and Paykel dishwasher is automatically starting its own washing cycle (well, motor starts, but no water appears to be entering), then it shows F1 error message and a spanner icon flashes. Within 30 secs of this occurring on one drawer, this starts on the other drawer. Only way to stop is to switch off at power socket. Any idea what the error message is telling me?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

After a few minutes the dish washer stops and error message LE shows up. This error message is not on the usual manual.


... LG LDF6810ST Stainless Steel Built-in Dishwasher

Dishwasher adp6000 shows error message 4 - meaning over filled. Have removed filter and drained bottom area. Now will not stop showing error message.


... Dishwashers

On an AM15T the temperature goes to 130 degrees max and I was getting an error message (E2) I think. I replaced the rinse probe outside near the vacuum breaker. I don't get the error message anym


... Hobart AM15T Dishwasher

"PE" error message on LG Dishwasher LD-12AS1 LD-12AW2


The PE error code indicates that the machine has a water pressure sensing error.\015\012Check and clean the filters on both sides of the inlet water line.\015\012Good luck! ... Dishwashers

Error code OE; dishwasher stops with error message 2 min into cycle, drainage seems OK, water doesn't appear to pump into machine - any advice?


Hi,The most common cause of an OE error code on a modern LG dishwasher is: 1. Blocked drain hose 2. Obstruction in the sump area (beneath the filter, which needs to be removed to check for onstruction) 3. Failing drain motor.& ... LG 24 in. LD-12BW5 Free-standing Dishwasher

NE error message on LG dishwasher


... LG 24 in. LDS 5811 Built-in Dishwasher

Error Message coming up


Hi, i work on these machines on a regular basis and until very recently i was a Meiko service engineer- the code ERR203 means that there was no change detected at the boiler level switch during emptying- be it on the fill or rinse cycle.\015\012This ... Meiko FV 40.2 Dishwasher

Euroart dishwasher error message


Hello. I know this post is a little old however I now need the manual Is there any chance you would be able to send it to me??? [email protected] you so so much ... Dishwashers

Error messages on dishwasher


The motor is bad ... LG 24 in. LDS 5811 Built-in Dishwasher

SE error message


You didn't say, but is the drain hose connected to a garbage disposal? If \015\012so, is the knock-out removed?Is the pump running or tryi ... Samsung DMR78AHS Builtin Dishwasher

Dishwasher will not start error message F3


Refer user manual. Contact service provider for assistance. ... Asko D1976 Built-in Dishwasher

My Miele Dishwasher (Excella Series G 2630 SCi) fails to fill. I get the message "Water inlet - Open the stopcock". I checked the water inlet filter and looked for hose kinks to no avail. I even checked the non-return valve. When I start the dishwasher I can hear a low hum (Not the pump) for a few second before the error message displays.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Detergent error I keep getting add detergent message. The bottle is not empty, the pickup line is submerged in the detergent & it tests acceptable. i also get an E7 error code once in a while. Thanks


I'm a hobart tech---been away for awhile.What is the model lxih,lx30?Let me know if you still have a problem with it. ... Hobart 24 in. LXIC-5 Built-in Dishwasher

-keep getting error message LE -doesn't clean well if it does get through a cycle without error. -sounds like it starts and stops every few seconds.


Same problem as mine and unforutunety fix was a replacement motor which drives pump. Bearings were shot in motor. Lots of people have this problem. If you are good at repair you can buy motor on ebay for $60. Impeller will have to be removed ins ... LG 24 in. LDS 5811 Built-in Dishwasher

I get an LE error message on my LG Dishwasher. I replaced the pump. Still get the LE error. Replaced the main control. Still get the LE. No blockage in the pump. What now?


When you receive the LE error code, unplug the machine for approximately 15 - 20 minutes. This will reset the microprocessor.Oversudsing is the main cause of LE error codes. Using non-HE detergents or too much detergent will cause stress ... Dishwashers

Hi There, I have a F&P Dishdrawer Model DD601v2. The top drawer has come up with an error message U3. Can you please advise what this error means and maybe how expensive it could be to repair or whether it's worth repairing? Many Thanks


This applies to all DD601 ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Hi i have a whirlpool dish washer - model : ADP4731/5 , AAA class . I keep getting a F7 error message and it is not allowing me to turn the washer on , if i hold the start button down it allows the washer to go for 30 seconds before the error comes back up and it stops working again


... Whirlpool Dishwashers

Error code Dishwasher has an error message of 1E. And an alarm goes off. It does not start.


The unit did not reach it's full fill level after 10 minutes.\015\012Check that water is not siphoning out as quickly as it fills. The drain hose must go up and attach under the counter top or go through a hole in the cabinet at, o ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0511 seconds