Having problems with your LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher ?

Dishwasher will start, but after a few minutes a noise starts. It will start and stop a few times and then it stop. The code LE appears.


Answers :

It is time to remove the filter down in the sump area, underneath the bottom spray arm. The spray arm comes off simply by pulling straight up. Also, the upper basket can come out by pressing on the gray clips, which will come off in your hands and then pulling the upper basket out. (It is a huge dishwasher inside, isn't it!)\015\012
\015\012Remove 10 phillips screws from the mesh filter and lift the brown "pipe" [which routes water up to the upper spray arms] off/away from the round top of the mesh filter.\015\012
\015\012Before returning the filter, rinse it out as best you can.\015\012
\015\012While the filter is out, inspect the sump area and remove the debris that is almost certainly there, causing the grinding sound you described. Be careful because broken glass is often found down there and it is almost invisible in the residual water that is always under there. Look closely, using a flash light to find everything that should not be there. Especially look at the little white impeller that is connected to the drain pump - it is towards the back and is the lowest place in the sum area.\015\012
\015\012While you are in there, look at the large impeller that is dead center. Look for damage and wear. Make sure it is secured with a philips screw and that it spins freely.\015\012
\015\012Reassemble the filter and the spray arm and test out. Please reply so I know if your problem was solved and what you found. Good Luck.\015\012
Repair Help & Product Troubleshooting for LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher will start, but after a few minutes a noise starts. It will start and stop a few times and then it stop. The code LE appears.


It is time to remove the filter down in the sump area, underneath the bottom spray arm. The spray arm comes off simply by pulling straight up. Also, the upper basket can come out by pressing on the gray clips, which will come off in your hands and ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

Hi I have a mdb6601awb maytag dishwasher. Sometimes when it starts the wash cycle it will make a loud squelling noise. Then if you pull on the handle and stop it, the machine will start and sometimes the noise will be gone. Or you may have to do this 3 or 4 times before it will stop making the squelling noise. I do notice when I pull up on the handle to stop the machine it makes some clicking noises and then the noise goes away. Thank You for any help you may be able to give me!!!


I don't have a solution however I have the same problem with that same model. ... Maytag 24 in. MDB6601AWS Stainless Steel Dishwasher

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

FDW60 Error code 3&4 . After reset m/c drains on all cycles. Start new cycle, m/c fills but then cycle stops. Makes bubbling noise and appears to overheat. Fault is same on all cycles. M/C drains on all cycles following reset.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hi I have a bosch classix maxi been great for the last couple of years but it has failed for the first time yesterday. The dishwasher did not start it just kept making a groaning noise and would not start the wash cycle. I can press end a noise changes but the noise just keeps goin for hours if not manually stopped. Any suggestions?


Completely unplug the dishwasher and leave disconnected for at least 10 mins.\012\012Also be sure to check the drain pipe is not kinked or obstructed and that the filter is also clean and empty ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

BEKO DWD 8650W DISHWASHER, AFTER HAVING GUESTS HOSE SIT FOR US WHEN ON A WASH PROGRAM (ANYONE) PARTWAY THROUGH THE CYCLE THE PROGRAM SWITCH EMITS A BUZZING NOISE FOR A PERIOD OF TIME THEN STOPS, AND CARRIES ON WASHING AS NORMAL. LAST NIGHT IT STARTED A WASH BUT STOPPED PART WAY THROUGH THE WASH AND THEN POWERED DOWN THEN BACK UP AGAIN BUT ALWAYS STUCK AT THE SAME TIME IN THE PROGRAMME, i TURNED IT OFF AND CHANGED PROGRAMMES WHERE IT EVENTUALLY MADE IT THROUGH A 30MIN WASH PROGRAMME, WITH THE BUZ


Dosent heat up or dry ... Beko Dishwashers

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

Hello, I have an LG-2120WHU and it has been making strange loud noises when washing for some time now. Then I tried running some anti-lime through a washing program and gradually, after several washes, it seemed to lessen the noise, but yesterday the dishwasher suddenly made a very loud noise and the I decided to try a special cleaning liquid from Neophos. Strangely it seemed as if the loud noises would slowly diminish, but in stead loud sqeaking noises started to appear and after I had run th


... LG Dishwashers

Dishwasher cycle starts briefly for a couple of minutes and then stops again and the standard wash and eco wash programme lights are then flashing together? It appears that water is drawn into the appliance for a short time and it then seems to start and empty itself before the above lights start to flash, all within 3-4 minutes?


... Hotpoint 23 in. BFV62 Built-in Dishwasher

My Frigidaire Dishwasher model FDB1100RHC2 has recently just stopped working. When I try to start it, the lights start to blink. It does not attempt to start or make any kind of noise. This is the first time that this has happened.


... Dishwashers

I have a prima lpr600 fully integrated appliance. it appears to start - emptying machine to begin with, then starting to pump in water - but then starts to beep continuously! the display light flashes 11 times before a pause, but i cannot seem to find what this error code means. please help!


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

Kenmore Ultra Wash water supply started making loud noise while water is entering washer. If you turn on sink faucet at the same time the noise will stop.


It sounds like the solenoid valves which let in the water are not fully opening and causing chatter -- probably corroded . Turning the washer-water supply faucets down (to the left) will probably stop it, but the solenoid valves need to be checked. ... Kenmore Dishwashers

My dishwasher will not start. The cecle time just keeps flashing, and the start button won't turn the cycle on. There is no error code, and the door appears closed properly


... Bosch Dishwashers

We have a Maytag built-in dishwasher Quiet Series model MDB8551AWB. When we press the Start, the lights light up, but after a few minutes all lights turn off. We've unplugged and plugged it back in. I've tried to repeat the 'start up' multiple times and sometimes it sounds like the motor is going to begin but then it pauses and stops. All lights turn off. No odd noises or grinds.


... Maytag MDB8851AWS 24 in. Built-in Dishwasher

We have a Maytag MDW700EDWG washing machine and it has stopped working. The display window is showing F2 and will not go to the time lenght of any program. I am unable to switch it off at the Start button. It is making a noise as if it is trying to do something - but then stops. I have cleaned the filters, checked water supply but still have F2 showing. Please can you shead any light or let me knoiw what to do Many thanks Emma


Is it the salt reservoir that is empty?\015\012Did you solve it already...mine has the exact same issue now ... Maytag Dishwashers

My mums AEG favorit sensorlogic dishwasher has stopped working. Now when you go to run a cycle it appears to start and then beeps 3 times (as if it has stopped) and nothing happens and the water does not come in.


Please check the timer ... Dishwashers

My whirlpool ADP 8540 starts, fills, then stop and flashes 6 times, pauses, and flashes 6 times repeatedly, until I end the cycle. What is this error code for? Can I fix it myself?


6 Flashes means water valve is switched on but flow meter senses no impulses (less than 10 impulses in 10 secs) and the water indicator is at a low level. Water Valve Closed or blocked.\015\012\015\012Water inlet valve defective. Flow met ... Dishwashers

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on


I just spoke with the Customer Service rep from Danby... She said tht an E2 error has to do with the hoses. Usually it means that the hose is too high to drain properly, there is a kink in the hose or the pump is faulty. Hope this helps! ... Dishwashers

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1383 seconds