Having problems with your LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher ?

I have an LG LDF7811BB dishwasher. Keep getting the "LE" error code. I have replaced the entire motor/pump assemble, main PCB, and both of the other PCB's still getting the "LE" error code. Was very pleased with the performance until this. Am I missing something?


Answers :

Hi,
\015\012This seems to be a very common problem withe these dishwashers. The LE error code (locked engine) is not allways indicative of a motor problem. Sometimes one of the gray wires which runs the length of the door panel was pinched and broken simply from the repetative motoin of opening and closing the door over time .Simply unscrew the front door panel from the retaining screws on the inside of the perimiter of the door. Once the screws are removed pull down and out to remove the door panel. Remove the sound insulating material and you will see several wires routed from the contol panel the length of the door to underneath the unit. Inspect the wires thouroghly. Near the bottom is where the pinching can take place. There are two gray wires and if you have been getting the "LE" error code, one of those wires is most likely broken or pinched. Splice, reconnect, solder or tape and you'are done.
\015\012sometimes The LE error code indicates solely a motor failure.Other than cheking the motor I recommend checking the harness at the motor. If the harness checks good & the new motor is not defective, you may need to replace the control board. This type of testing will require using a volt/ohm meter.
\015\012Thanks for contacting fixya.com
Have a nice day.
\015\012GodBlessU
Repair Help & Product Troubleshooting for LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an LG LDF7811BB dishwasher. Keep getting the "LE" error code. I have replaced the entire motor/pump assemble, main PCB, and both of the other PCB's still getting the "LE" error code. Was very pleased with the performance until this. Am I missing something?


Hi,\015\012This seems to be a very common problem withe these dishwashers. The LE error code (locked engine) is not allways indicative of a motor problem. Sometimes one of the gray wires which runs the length of the door panel was pinched and b ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Hi, we have an LG dishwasher that keeps getting the OE error. I called LG, and she had me check a couple of things, including checking for kinks in hoses, making sure dishwasher is still level. Is this something I might be able to remedy myself?


Hi,\015\012\015\012There are few reasons why you are getting OE error. For example some debris stuck in the pipe or there might be a kink. But to do the fix I would request you to go through the official troubleshooting link posted bellow ... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

The detergent dispenser [Main Wash] door doesn't stay closed. It seems like there is something wrong with the latch, but we can't what. We've cleaned it, but don't know what else to try. There don't seem to be pieces missing or broken. But no matter what, when we put in the detergent [we use the cubes] the door always just pops open and the detergent ends up falling to the bottom on the dishwasher. The dishes are still getting relatively clean, but we want to solve the problem with the door


... Frigidaire FDB1200RG 24 in. Built-in Dishwasher

I get an LE error message on my LG Dishwasher. I replaced the pump. Still get the LE error. Replaced the main control. Still get the LE. No blockage in the pump. What now?


When you receive the LE error code, unplug the machine for approximately 15 - 20 minutes. This will reset the microprocessor.Oversudsing is the main cause of LE error codes. Using non-HE detergents or too much detergent will cause stress ... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

We have a Kenwood KDW8ST2A dishwasher. We used to get the error code E3 (when still under warranty) and were told not to use dishwasher tablets as it generated too much foam. The problem has been intermittent but now we get the E3 error every time, no matter what program we run, or how little detergent we put in. I've a feeling its not heating up properly, is there any way to check the heating element? Is it worth attempting a repair?


... Kenwood KDW243A Builtin Dishwasher

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

Our maytag is about ten years old. No big problems that a little vinegar wouldn't solve once in awhile. Lately, we ran out of water softener salt and a white film was on dishes and not getting clean. I filled the water softener again, and did the vinegar wash, which helped a little. Now dishes not getting clean. I got desperate and did an empty load with CLR in it. Still, not effective. I feel as if something is clogged with lime or calcium since a pan placed in there on bottom shelf still had


The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the ... Maytag 24 in. MDB4100 Built-in Dishwasher

What does the F2 Error mean? I got that error thsi morning. The engine was buzzing so I turned the power off. I have cleared what appears to be calcium and/or soap build-up in the 3 filters and in the drain. When I turn the power back on I still get the F2 error. How can I restart the machine and turn off the F2 Error?


The F2 error means the tray underneath the unit has filled with water.\015\012You will need to pull out the dishwasher (remove 2 screws at top left/right when door open that prevent tilting).\015\012Unplug and pull out dishwasher.\015\012Remove 4 scr ... Asko D1876 Dishwasher

Hi, I get a problem reading " E4". I have now switched the machine off and on again, but still it says the same. Incidentally the machine has already pumped the water out, so the 'overfill" is actually not supposed to be a problem. It is KELVINATOR EXTREME CLEAN DISHWASHER, model KD14SS. Please help, how am I to get rid of this problem, I really do not have the time nor the money to get outside help! Anita Kleynhans


... Kelvinator MDP531RF Dishwasher

My portable maytag dishwasher puts out a stinky smell during wash cycle i tore the inside apart and washed everything i also took off the outside part to just to make sure that something didn't get caught under it or something and its still putting out foul smell what could it be


... Maytag 24" Tall Tub Portable Dishwasher - Black

Hi where can I get operating manual for Siemens ecosense dishwasher. recently bought property and appliance was already installed. Previous owner did not leave a copy and i now get E24 error code, with water remaining in base of unit - assume something to do with waste pump or pipe?!


... Siemens Dishwashers

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers

Not cleaning my dishwasher goes thought all it's cycles,but when it is done the dishes are still greasy and the top dishes are still dirty.i have checked the water pressure the psi is 64. i have also cleaned all the wands and drain.can you please give me something less to do.my dishwasher is only 3 yrs old. i have not been able to use it in about a year know.


Check the wash arms make sure that they can spin ... open in mid cycle check water level and arm spin...also check water temp... hope it helps ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

The oil in my gc160 Honda pressure washer is getting water in it some how. Could it be something with the water pump gasket or what? And I can get it started but can't keep it running un less I keep spraying starter fluid in the carbar. Please help ?


... Karcher 2500 PSI Pressure Washer

Within the last month our GU1200 is noisy and not getting the dishes clean....I did pull out some melted clogged debrise from the "dish module". WOndering if something else is still in side? and how do I dismantle the lower spray arm to get inside and see?


THERE SHOULD BE SOMETHING HOLDING IT DOWN, JUST BE SURE THAT YOU REMEMBER THE SEQUENCE OF PARTS. THE MELTED PARTS ARE FROM THE DRY CYCLE WITH PLASTIC LAYING ON THE ELEMENT. SOMETIMES THERE IS A PLASTIC THREADED PIECE OTHER TIMES IT IS A METAL SCREW ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Maytag mdbtt79 high current error but have checked everything broken impeller was replaced but still getting error is there a way to reset the control board have checked with ampmeter and current is with in specs


You may need to check connections on the control board,it may be receiving a "glitch"code from poor connections ... Dishwashers

Kenwood KDW12ST3a E3 error replaced heater and thermostat still get E3 error


... Kenwood Dishwashers

Error e3 My dishwasher gets halfway through the cycle and then comes up error E3.  It is a hoover hd97e. Please help Fiona


Drain pump probably not working. Put machine on cycle 7 and it should turn on the drain pump straight away. you can hear this near the bottom of the machine. if it is silent hten the pump probably needs replacing. I repaired mine be removing it and t ... Hoover 24 in. HD97E Free-standing Dishwasher

DW 955. F2 error still flashing after water has drained. Can't get machine to switch off this error.


... Asko Dishwashers

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring The solution I tried didn't clear the error code on the panel. Is there a reset or do I need to replace the aqua sensor or ? The machine still won't start and displays a #1 on display. There is no water in the whi


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

GE 18" dishwasher getting VERY loud. Well over 100db. Is this a sign it is dying or can I get it fixed? It has gotten louder in the last year. It still washes about the same but sounds as if it is on its last legs. Is this something you are aware of and is a serviceable issue / parts or is it fatal?


May not be fatal. Could just need a new motor. ... Dishwashers

This is the second time in 2 years my door to the dishwasher slammed open and hit me in the shins. A spring or something was replaced once ALREADY how do I get this repaired again? I thought buying a kitchen Aid I would not have problems Please help I am afraid someone will get hurt.


Hi,\012That is not that hard to fix and you can easily buy the parts yourselfonline...Here is a tip that will help you with the online buying...How to Buy ... KitchenAid Dishwashers

Hello, Please help. I follow recommendations for cleaning: sewer pump, cleaning arms, screens of the dishwasher. However, still machine is not working. water is not going through arms: lower, middle or top. Also, I get water into dishwater when it starts, and when I open i hear noise for water dripping into hot elements,but no water is running throughout. PLEASE HELP


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1377 seconds