Having problems with your LG 24 in. LDS 5811 Built-in Dishwasher ?

Oe error...manual says clogged but cant find clog

\015 Oe error\015

Answers :

It is important to start where the drain hose connects to the drain. Probably connects indirectly to the garbage disposal. Look for blockage there and work your way back to the dishwasher.

IF you can't find a blockage, then it is time to remove your lower spray arm and the approximately 9 screws that secure the filter assembly to the sump floor. Rinse everything that you remove.

Using a flashlight, inspect the entire sump area for debris (watch out for broken glass!) Look closely where the drain pump is located. You will probably find some sort of blockage jamming that pump.

Reassemble and test. It is rare, but an OE error could be created by a failing drain pump motor. But try everything else first.

Good Luck!
Repair Help & Product Troubleshooting for LG 24 in. LDS 5811 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oe error...manual says clogged but cant find clog


It is important to start where the drain hose connects to the drain. Probably connects indirectly to the garbage disposal. Look for blockage there and work your way back to the dishwasher.IF you can't find a blockage, then it is time to ... LG 24 in. LDS 5811 Built-in Dishwasher

Our MDB7100AWQ flashes the light that the troubleshooting sheet says means: "Turbidity sensor fails to find clean water" I cleaned a lot of gunk out of the screens but the code didn't change. Do turbidity sensors get clogged up?


Yes, depending on how it is mounted, ther could be gunk in the stub of pipe or a film caused by hard water on the sensor, pull the sensor and clean. ... Maytag MDB7100AWB Dishwasher

Water gets too hot on all progs - thermostat gone, presumably. It is an integrated dishwasher, and cant find model number. Manual says 9000 112 902 (8507) but no apparent model number.


... Bosch Dishwashers

I have a maytag dishwasher model MDB9150AWQ the diagnostics call the turbidity sensor. But I cant find one to buy thay all say NLA can yoy help Ralphj


Since they don't make the one you need anymore, you may not be totally out of luck, usually they make one that will still work but call them directly to confirm this. I think the one located at the following website may work on yours but there was no ... Dishwashers

I have a kenmore ultra wash mod# 665.13492k600 dishwasher that in the last couple of days will not drain the last cycle . If you push the cancel /Drain button after the cycle is finished it will then drain but all the dishes have soap spots on them and are very wet .I have checked for clogs but cant find any I have also run a lot of water throug our waste disposla because the dishwasher drains into it help ??


... Kenmore Dishwashers

Whirlpool DU1055XTSS dishwasher is totally dead as if it were unplugged. No response from front lights. Only 3 years old. Another post for an different Whirlpool model says it's the thermal fuse, but I cant find that part for this model.


Hi,If you have power going to the dishwasher, meaning the breaker, switches, wiring and fuses in the home are okay, the most common cause for your symptoms is the thermal fuse. The thermal fuse is a small disk shaped device th ... Whirlpool DU1055XTS Built-in Dishwasher

Display says E01 and cant find my manual for lifestyle automatic


... Dishwashers

Beko dwd3410s dishwasher water not heating up cant find a manual for it and cant find the heater element


Go to www.beko.co.uk\015\012then to support & at the bottom of the list is manuals ... Beko Dishwashers

I have a Kenmore Quietguard dishwasher, only a few years old, and it won't drain. I pulled it out and checked the drain hose, could not find a clog. I took the basket and sprayer out, couldn't find any clogs there. It seems to be making a little bit of a different noise but does still clean the dishes. Does the motor pump the water out and could that be the problem?


I have a Kenmore Quietguard portable that won't stay connected to my kitchen sink faucet. Checked all I can and continues to spray the wall and me without staying attached securely to the faucet adapter. Help!! Any ideas? ... Kenmore 24 in. 15162 Built-in Dishwasher

Cant find rinse aid container


Many old dishwashers don't have a drying aid dispenser. If you have one, your will find some sort of cap to remove in the door, near where you place the detergent powder.\015\012\015\012If you don't have one, you can buy an alternate vesion fo ... Dishwashers

Clogged Dishwasher The water won't drain out and I believe my dishwasher is clogged up. Where do I look (I'm assuming at the bottom of the appliance) to find the clog so that I may fix it?


First - if you have air gap on top of your kitchen sink, remove the cap and check if there is a ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Like sand Not getting the dishes clean it seems like sand and other stuf in the glasses :( cant find any extra filters , have clean the regular ones in the bottom of the machine. Please can someone help me find a solution or find a manual online.


Clean out both top and bottom spray arms\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

WE HAVE GOT A BOSH DISHWASHER AND IT DOESN'T HAVE A CODE WE CAN ONLY FIND NUMBER 900035833 WHICH WAS INSIDE IT AND WE CANT FIND A manual to mach it


... Bosch 24 in. SGI43A72 Built-in Dishwasher

Hi I have a bosch diswahser smu 7000. No power when I push button. Manual says its could either be fuse or circuit breaker. Checked breaker its ok. My manual does not say anything about location fuse. Called bosch. And they said they cant tell me. I nee to have a service call. Any help. Thanks.


... Dishwashers

I have a dishlex global 270 i cant find a model no i only have a serial and manufacturers no. What i wanted to find out is does this model have an element that heats the water. I only have one hose and when i used it with cold water it didnt heat up so i am using hot water.


Hi\015\012\015\012\015\012Thanks for using FixYa. I hope you understand that no one can tell you what are the specifications of the product until you provide the model no# however, dishlex usually have element in their dishwa ... Dishwashers

Its happened before i have a kud101flss6 diashwasher and something trips the computer a repairman came and pressed a sequence of buttons on panel and fixed it cant find repairman and cant remember sequence help


Usually an interruption in the dishwasher program results in a blinking "Clean" light. This commonly indicates a component problem or program malfunction. If a\015\012component is defective, it's usually attributed to the heating cycle or\015\012the ... Dishwashers

Just installed fisher paykel model 88270 dishwasher, bottom drawer has no power,and top drawer does not fully drain. Cant find another power cord, is there a second one? Cant locate the manual.


... Fisher Dishwashers

Hotpoint fdw70 error code A10 have replaced the inlet water valve but still have an error code flashing A10 hoped to find a reset button but cant find it anywhere can u possibl advise.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

I am trying to find what model number our dishwasher is so I can try and find a part for it. It says on the front Maytag Jetclean dishwasher quiet plus. I know its an older one but we are renting and I don't know when they installed it.


If you open up the door, you should be able to locate and see a factory label along one of the sides of the cabinet, where the door closes. \015\012\015\012It might be on the top edge, too, depending on how old it is, but you should be ab ... Dishwashers

My deceased parents have a GE dishwasher (don't know the model number - can't find it on the machine and can't find the paper work) that stops working shortly you start it and displays a message on the front panel that says "Blocked wash arm - check for wash arm obstruction - restart". We restart it and get the same message shorty thereafter. This happens when the washer is COMPLETELY EMPTY, even when we remove the bottom rack. It first started after several month of inactivity. We'll just t


Could be false sensor input, could be that the arm is not turning, I am not sure how old your machine is, but age could play a part if the arm is "in fact", not turning. If you are not mechanically inclined, I would suggest that a qualified repairma ... Dishwashers

Hobart LX30 Thank you for your help earlier. I figured out a way to get the machine running on 220. Now my problem is finding the intake for the sanitizer and detergent. I have looked all over the machine and I cant find tubes anywhere. The guy I bought it off of tells me that when the water temp is over 170 you don't need any cleaning products. I just want a second opinion. I feel that our glassware is not as clean as we would like. Any thoughts?


I'm not sure I'm comfortable with the direction your seller is leading you. I assume this machine is installed in some type of place where you are serving food to the public. If this is the case, then the local health inspector will expect to see a w ... Hobart 24 in. LXIH-3 Built-in Dishwasher

SEARS/WHIRLPOOL DISHWASHER Model 665.16014401. The CLEAN light keeps blinking and washer will not run. Op. instructions say to check the heater circuit. Heater element tests at 12.9 Ohms and thermo unit at 55 K ohm and the unit I beleave looks like overtemp cut out is less than 1 ohm. these look like good #s to me so I suspect the controller p/n 8564544. When I look up the number online I find it has been replaced with 8564546, but the only picture I can find of it looks like the connections are


... Kenmore Dishwashers

Dishwasher problems I have a counter top dishwasher and it's not cleaning things like it used to i think its clogged but i cant get to the drain because it is in the bottom i tried draino but it didn't work i also tried unscewing the bottom but i cant get that part out i think there is somthing stuck in there.


First thing to check water hose that connect at back of machine. pull the screen out and clean it. use a pliers. I run my under water then use a q-tip if its clog to clean the rest.\015\012\015\012Then pour a cup of vingar in machine and ... Danby 22 in. DDW396 Free-standing Dishwasher

My KitchenAid undercounter Sculptura dishwasher Model KUDV24SE will not work. There is a message panel that says: "Rinse and empty energy monitor". The Use and Care Guide does not say where this is or how to find it. Where is it and is this something I can do myself?


I am pretty sure you are reading two different indicaters. One says Rinse Aid Empty, which means your rinsing agent dispenser is empty, This is in the door, unscrew and fill, don't overfill, usually lasts 3 months. Energy monitor is under this and ... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0642 seconds