Having problems with your LG 24 in. LDS 5811 Built-in Dishwasher ?

My LG 24 in LDS 5811 ww quite working in the middle of a cycle. I have power to the machine, but no lights come on, nothing works. I turned off the power and removed the front pannel. The large brown wire and large orange wire that are plugged into the back of the control panel start to smoke. So does the large black wire and the large white wire. Any ideas, is this the heater or is the panel bad?


Answers :

The unit will need a new Wire harness, Pump/motor assy, Main Pcb and inner door liner.
\015\012Contact LG @ 1800 243-0000 they may help you out.
Repair Help & Product Troubleshooting for LG 24 in. LDS 5811 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My LG 24 in LDS 5811 ww quite working in the middle of a cycle. I have power to the machine, but no lights come on, nothing works. I turned off the power and removed the front pannel. The large brown wire and large orange wire that are plugged into the back of the control panel start to smoke. So does the large black wire and the large white wire. Any ideas, is this the heater or is the panel bad?


The unit will need a new Wire harness, Pump/motor assy, Main Pcb and inner door liner.\015\012Contact LG @ 1800 243-0000 they may help you out. ... LG 24 in. LDS 5811 Built-in Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

I have a GE Quiet Power 3 built in dishwasher. With 1 min. left in a cycle, I opened the door, removed an item, then closed the door again, but it didn't finish the cycle. The machine continued its single beeps to indicate the door was open. Reopened and closed the door. None of the buttons on the control panel respond. Have unplugged and left overnight, plugged back in, beeping continues.


... GE 24 in. GLD6500L Built-in Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

We have a kitchen aid dishwasher model # kudso1msso -- quit working and the control panel button lights are out so i assume there is no power to control panel. we have power at the plug every else looks ok. . could the internal fuse at the control panel be blown or the circuit board blown.


Sounds to me like a 'breaker' must be thrown; ... KitchenAid Dishwashers

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.


I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

My GE Dishwasher, Model GSD6960N10SS, has no power. None of the lights on the control panel are lit. The circuit breaker is on and the wall control switch is also on. I turned off the power for 30 seconds and turned it back on, but there is still no power.


... GE Dishwashers

My Frigidaire FDB956RBC0 has been having trouble resetting on the control panel for a new load. At first I could push several buttons or wait a little bit for it to reset then I could push start. Now I have to open the front panel & pull out a yellow & white plug, then plug it back in to reset the buttons for a new load.


... Frigidaire FDB956RB Built-in Dishwasher

LG dishwasher quit mid cycle. no power to the front panel. I drained the water and found a two pronged wire by the drain hose disconnected. reconnected it and I still get no power on the control panel


Here is the video for you its intresting to get it repaired V ... LG Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

LE on display panel. I have taken front panel off and all wiring has already been electrically taped together, so I don't think it is wiring. (This was done by a service rep when I had 1E problem) How do I tell if the impeller, rotor or blade is blocked? Or sump assembly or main power control board needs to be replaced?


Http://www.justanswer.com/questions/2bijk-i-have-a-lg-ldf6810st-dishwasher-with-an-error-that-the-serv ... LG LDF6810ST Stainless Steel Built-in Dishwasher

No power I have no power.  I checked the plug and it had no power, so I reset the breaker.  Power returned to the control panel.  I selected normal wash.  It started up and 2 seconds later no power again.  Breaker flipped again.  What is the problem?


... Jenn-Air JDB7910 Dishwasher

No power to control panel after power surge


1. No power to the dishwasherMake sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, beh ... Maytag MDB7100AWB Dishwasher

I have a Whirlpool Gold Model GU2700XTSBO its only 4 years old. About two weeks ago i noticed that the green lights were flashing and it would not run, I unpluged it for an hour and pluged it back in and the lights went away and it worked ok for the last two weeks. Last night I went to use it and there is no power at all to the washer, I checked the power source to the outlet and there is power there, so I dont know if there is a reset button or some control panel problem?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

No power to control panel


... Bosch Dishwashers

We had a power surge and the guy who looked at it said my control board was fried. It looked to me like a plug in item easily replaced by anybody with a screwdriver to take the door panel off, however in trying to find the part nothing is called "control board". What is it>


Its called a pcb call ge and order a new pcb for the make and model ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Installed a new control panel on my PLD4375RFC0 dishwasher and when power was turned on the PF light flashed then went off when the door opened. However, the screen remains blank even when pressing buttons to apply a setting. Have cut power and turned back on several times with same results.


... Frigidaire PLD4375RFC Dishwasher

Gld4260l00ss has power. there is light indicators on front panel, but when press start button, nothing. new inlet water valve solenoid installed last month and unit has ran fine until two days ago. I have unplugged power and plugged back in but no help.


I would remove the control panel and ck the ribon form the touch pad to the control .it is very common for these connections to fail remove the ribon and re insert it and try again . also ck the touch pad and make ... GE GLD4260LSS Dishwasher

Just will not start like it has no power to it. Checked breaker box and made sure everything was plugged in under machine. There was one white wire that was not slid on in front. Plugged it back on ,still does not start


A voltmeter is very handy with a problem like this. If you have proof of power available at the junction box under the machine, then the next likely place to look is within the latch mechanism inside the door. There is usually a microswitch which act ... Admiral Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0812 seconds