Having problems with your LG 24 in. LDS 5811 Built-in Dishwasher ?

Does not fill with water e1 code

\015 Does not fill with water ie code\015

Answers :

1E means - Water inlet problem >Condition : Not reached to the normal water \015\012level in spite of 10 minute water supply


Water supply problem. The inlet hose is kinked. The water pressure is to\015\012 low (10psi) Inlet valve. The inlet water valve filter is clogged. The \015\012hall sensor. The impeller of Air guide is bound. \015\012Remedy : Check resistance of inlet valve ( 950-1300ohms) Clean valve. \015\012Check pressure. Replace the Air braker.
Repair Help & Product Troubleshooting for LG 24 in. LDS 5811 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

I have a Dishlex Global 500 dishwasher (DX500lWW*b). Woke up the other night to find water all over my kitchen floor. The hot water hose connector to the hot water tap split (bursted). The dishwater was not in operation at the time but I can only assume when the hose bursted the dishwater came on to alert me? the code on the dishwater is displaying ''oF'' - which means Incorrect fill level of fill time. I have consequently had the hose connector repaired but the display still has the code ''oF''


I found this\015\012\015\012"Hi - answer I was given by Electrolux Help was: pull machine out from under bench onto old towel, tip GENTLY onto left hand side (your left as you face the front of the machine) after it has drained, stand up ... Dishwashers

De Dietrich Dishwasher - DVH 610 JUI - when turned on to any programme and started automatically tries to drain water instead of filling with water. Was disconnected and filters checked and were clean. when turned on again it worked and when disconnected to be brought back into house it again tried to drain water instead of filling. All lights come on except blue light. Does not accept engineer code given with wiring leaflet


... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Serial #88445-B Rym 717881 model # fpdd 603 We are getting a fill fault code when we start the dishwasher. When the alarm goes off we have to pause the wash cycle open the door and then close the door if we do this about 2 or 3 times it will wash. It seems it fill with water but it seems to be low on water Dave Heller


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

My Maytag Model # mdb7130aww will not fill with water. I did the auto function test and it completed without any codes but when the water valve was supposed to come on, it didn't. Everything else functioned. I tested the resistance of the valve and my multimeter went from 1 to .90 or so when I checked the terminals. Also, this problem is intermittent and when I check the voltage to the valve it reads around 70 unplugged and 120 when its plugged up to the valve. Does this mean the water cont


... Maytag MDB7130 Dishwasher

Hello! My GE Dishwasher (Model # GSD2000G00WW) will not fill. The water supply is flowing properly after cleaning out some lime and mineral deposits, but no water is going into the machine. If the water flow valve needs to be replaced (?), is there a local distributor in the Cincinnati/Blue Ash area in Ohio (zip code is 45242)? Thanks! Steve Brodbeck


I need to know is the water not going in the machine at all in other words when you switch on the machine with the tap open can you hear the water flowing,if you can here the water flowing check the hight of you drain hose if it is too low down you w ... Dishwashers

I ran a load of laundry in whirlpoo[ duet ht, model ghw9400pl4, error code p-09 was indicated. water was overflowing from door, and water was continuing to fill the tub. I turned off the faucets, unplugged & restarted in drain mode it hummed but would not drain. I turned the faucets back on and retried to drain but it would only hum. I manually removed the water by losening pump filter. There was no debree in filter except for a little bit of hair. The pump & vain was free & clean, and I co


It is your mixer value that is malfunctioning. ... Whirlpool Dishwashers

Does not fill with water e1 code


1E means - Water inlet problem >Condition : Not reached to the normal water \015\012level in spite of 10 minute water supplyWater supply problem. The inlet hose is kinked. The water pressure is to\015\012 low (10psi) Inlet valve. ... LG 24 in. LDS 5811 Built-in Dishwasher

My Fisher Paykel dishwasher is model #DD6051. After about 1 1/2 years, the top drawer is not filling with water. The fault code looks to be U1. The bottom drawer fills and runs fine. Would you have any idea what the issue might be? Thank you very much.


Hi,Unplug the Washer for Few Minutes, say 30 minutes and then Turn it ON. If the problem Persists, then read :-U1 Heavy and Rinse LEDMachine has failed to prime with water within approx. 3 minutesReason ... Fisher and Paykel Dishwashers

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

I have a belling IDW604 it starts to fill and the program light flashes but it stops within 15 seconds or so. When I open the door it has just filled the bottom filter with water. I have no error code. Any advise please?


I have the same problem .i searched the net and cant find a solution .any help would be great ... Belling 24 in. IDW603 Built-in Dishwasher

Ignis adl348 starts normally, fills with water then stops. Fault code is 4 flashing lights, I think the pump is blocked as i pulled a kids medicine pump syringe out of the waste water outlet in the sump?


... Whirlpool Dishwashers

Bosch SHI 6800 Dishwasher. Fills with water and heats but doesn't spray water around (ie run). Shows code "2H" on lighted display. How can I fix it?


... Bosch 24 in. SHI68 Built-in Dishwasher

Hi my Candy dishwasher model CDI 1012/2 is filling with water then after a few minutes if bleeps and the error code meaning according to the manual is "Longer inlet time. possible cause Faucets is not open" The tap is fully open and the dishwasher is now full of dirty water. Could you please suggest an alternative cause?


... Candy Dishwashers

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Our Asko 3530 dishwasher is giving us a 'water inlet fault' code. The machine goes through the pre-drain at cycle start then begins to fill, continues until it's full then kicks out the fault code. I have changed the inlet valve, reset the system to factory default and taken off the lower front panel, finding the overflow area to be dry. Is it time to call for service or is there something else to try before spending the big bucks?


Hi,This sounds like either the overflow sensor or the water control valve is stuck.Usually the valve is a solenoid valve that controls the entrance and fill of the water. If the overflow sensor is underneath, there may be wate ... Asko 24 in. D3530FI Built-in Dishwasher

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

My hobart lx 30 will not fill all the way. iv bin to hobarts online manual and iv got plenty of pressure..flashing wrench e-3 code etc...added 2gallons water but presumebly since it wasnt 150degree water that didnt help as all i was able to do was turn off and back on and watch the 3gallons expell


LOOK FOR WATER PRESSAURE SWITCH PROBLEM ... Dishwashers

Hoover dishwasher showing error code E1 seems to start the a few minutes stops. No water filling up but some water in the bottom. What is wrong?


... LG LDF6810ST Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1248 seconds