Having problems with your LG 24 in. LDS 5811 Built-in Dishwasher ?

The motor continues to run with the diswasher powered off. In addition it will no longer enter wash mode. It can be powered on and wash mode can be selected, but nothing happens except the motor continues to run. Cycling the power feed off and back on does not solve the problem.


Answers :

Hello John,
\015\012
\015\012The simple answer (without looking at the wiring diagram) is the float switch. The simple answer (after looking at the wiring diagram) is the float switch. I've posted the wiring diagram for this washer to Flickr for you:
\015\012
\015\012http://www.flickr.com/photos/[email protected]/5571542445/sizes/l/in/photostream/
\015\012
\015\012The float is a secondary water level sensor. It detects when the washer is overfilled or there is a leak into the bottom of the washer under the tub and activates the flood-protection system. This closes the water inlet valve and runs the drain pump motor continuously. Basically, you either have a leak, the float is stuck or the float switch is faulty.
\015\012
\015\012Hope this helps. I definitely wouldn't suggest switching out the control PCB. Have a look at the wiring diagram and check under the tub for any signs of a leak, then let me know if you need further assistance.
\015\012
\015\012Regards,
\015\012BElectric

Hi
\015\012\015\012

The issue is with the motor that is bad and should be\015\012replaced. Please check this video, its an example though but will help you:
\015\012\015\012


\015\012\015\012

Hope this helps...please post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for LG 24 in. LDS 5811 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The motor continues to run with the diswasher powered off. In addition it will no longer enter wash mode. It can be powered on and wash mode can be selected, but nothing happens except the motor continues to run. Cycling the power feed off and back on does not solve the problem.


Hello John,\015\012\015\012The simple answer (without looking at the wiring diagram) is the float switch. The simple answer (after looking at the wiring diagram) is the float switch. I've posted the wiring diagram for this washer to Flick ... LG 24 in. LDS 5811 Built-in Dishwasher

FISHER & PINKEL DD603-SS BOTTOM DRAWER SECTION, WILL START TO FILL THE THE DOOR LOCK SOUND WILL KICK IN AND CONTINUE FOR SEVERAL MIN WITH THE WASH WILL TRY TO START BACK AND FORTH. ALSO even with power off the motor sound will go for several min???


... Fisher DD603B / DD603W / DD603H Dishwasher

Smeg df612sdx Until last week I enjoyed several years faultless service from my SMEG Stainless Steel dishwasher, with the exception of needing to replace 2 x spray arms. The unit has now stopped working altogether. Despite powering up several times, I continue to get both the start/pause and selection programs buttons constantly flash (green lights) when the unit is switched on; previously this only occurred once the wash cycle was complete. Any thoughts would be most appreciated. Thank you


... Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

When I start my GE Quite Power 1 dishwasher it makes a rumbling sound eminating from the base probably the water spin mechanism that sits on the motor is my guess? As the cycle advances the noise continues, any idea what is causing the rumbling noise to occur during the wash cycle?


Your issue could be one of the following:\015\012\015\012* motor\015\012* water pump\015\012* vibration from some source \015\012\015\012Contact an appliance service company. ... GE Dishwashers

Three year old Amanda dishwasher won't run. Normal wash light flashes continually Turn off power and cancel light flashes five seconds machine tries to run five seconds then back to flashing light.


... Dishwashers

I HAVE ONE KELVINATOR DISHWASHER SOME 20 YRS OLD, BUT BRAND NEW, NEVER USED. MOD: K15 3726800611 10 A 220V 50 HZ TOTAL POWER CO W 2050 WATER HEATER RESISTANCE W 1800 WASHING MOTOR DRAIN PUMP W 250 90 FRONT DOOR WAS OPENED FOR REPAIR AND NOW CANNOT FIX IT BACK. KINDLY SEND ME INSTRUCHTIONS WITH DRAWINGS. M. ZAFAR IQBAL 840 SHADMAN 1, LAHORE 54000, PAKISTAN email: [email protected]


... Kelvinator Dishwashers

I HAVE ONE KELVINATOR ( KELLY ITALIA SPA) DISHWASHER SOME 20 YRS OLD, BUT BRAND NEW, NEVER USED. MOD: K15 3726800611 10 A 220V 50 HZ TOTAL POWER CO W 2050 WATER HEATER RESISTANCE W 1800 WASHING MOTOR DRAIN PUMP W 250 90 FRONT DOOR WAS OPENED FOR REPAIR AND NOW CANNOT FIX IT BACK. KINDLY SEND ME INSTRUCHTIONS WITH DRAWINGS. M. ZAFAR IQBAL 840 SHADMAN 1, LAHORE 54000, PAKISTAN email: [email protected]


... Kelvinator Dishwashers

The dishwasher washes the dishes but continues to run. I had to turn off the main switch. Turning is back on causes the motor to start up again even though the door with open.


... Thermador DWHD64EP Built-in Dishwasher

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

My dishwasher, Whirlpool IKEA DWH B10, has jammed on a setting. It is continually going and I can't stop it without turning the power off, but it starts up again if I turn the power back on.


... Whirlpool Dishwashers

Wash pump motor removal to clear wash pump of a large object.we have washer out of cabinet on it back on the floor. Need to remove wash pump motor to access wash pump to clear a large object from the pump rotors.


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.


Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers

I have a model SHE 44 C05 UC/40. It is three years old. It starts up fine, fills with water and goes into the wash cycle. Then it continues to wash indefinitely, even though the electronic timer display counts down to 1 and sets there. It still continues washing until you turn it off with the power button


... Bosch Dishwashers

Power washer I have a karcher power washer and it haves a 7.0 robin motor on it... When i start it up the motor just goes in to high speed... I looked to see if all the springs are on the arm and they are ....All i can think of that the governer on the motor is not kicking it back... If you could help that will be great....Thanks Jerry


... Karcher 2500 PSI Pressure Washer

Remove the lower wash arm (1) by turning the nut (4) clockwise (right) lift the arm off, there is a bearing (3) (small thin plastic washer) under the arm, be sure not to loose it. Lift the tab on the back of the feed tube cap (2) and swing it to the right and lift up, this may need a bit of pressure to release it This is for my Whirlpool dishwasher DU1100XTP. I'm putting it back together and can't remember if the plastic washer goes on top or underneath the feed tube cap. Also how do I remo


This is not a tuff job plastic washer goes on top . and torx screws . you use a proper torx tip for the screw size . ( you can go to sears parts .com and put in model # and see a good break down of the wash arm s and t ... Dishwashers

Bosch D/W model # SHU9955UC. The drain motor will not stop running. Ran the reset sequence on the panel. Display reset to "0" minutes. Power cycled the D/W and when powered back on the drain motor started up again. What do I do ?


Hi ....This is a common problem. Remove the kick plate you will see the white base which also is a tray to collect leaks or backups. Reach your fingers over the top of tray and feel for water/wetness,if so safety switch has been activated and pump wi ... Bosch SHU9955UC Built-in Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

I have a KitchenAid KUDp02FRSS1 dishwasher and it will not respond to any buttons being pushed. The Normal, Light China and Cancel lights continue to blink. I have tried reseting the circuit breaker to power cycle the machine but when I turn the power back on it just continues to blink.


... Dishwashers

Dishwasher fault had leak,when opened bottom plate, could not see any obvious leak problem,hand dryed what componets i could. made sure no wires were loose then screwd back bottom plate,turn power back on but power button flashing continuously know,any advice plz


The flashing power button is a bad sign. You may have flooded the circuit board out or there may be a bad component as a result of the flood. Difficult to know from here.\015\012\015\012Most flooding on dish washers is caused by a faile ... Dishwashers

BEKO DWD 8650W DISHWASHER, AFTER HAVING GUESTS HOSE SIT FOR US WHEN ON A WASH PROGRAM (ANYONE) PARTWAY THROUGH THE CYCLE THE PROGRAM SWITCH EMITS A BUZZING NOISE FOR A PERIOD OF TIME THEN STOPS, AND CARRIES ON WASHING AS NORMAL. LAST NIGHT IT STARTED A WASH BUT STOPPED PART WAY THROUGH THE WASH AND THEN POWERED DOWN THEN BACK UP AGAIN BUT ALWAYS STUCK AT THE SAME TIME IN THE PROGRAMME, i TURNED IT OFF AND CHANGED PROGRAMMES WHERE IT EVENTUALLY MADE IT THROUGH A 30MIN WASH PROGRAMME, WITH THE BUZ


Dosent heat up or dry ... Beko Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

After a power outage, my GE monogram dishwasher beeps continually. The controls are not responsive. I've tried turning off the power to it (by the fuse box) but the noise resumes when the power comes back on.


Unfortunately, if you lost power as a result of a lightning storm or a power surge, there is a good chance that your dishwasher was exposed to a power surge that may have damaged the control circuitry. During these types of events, there is no way of ... GE Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1607 seconds