Having problems with your LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher ?

I get error code le on LG dishwasher.

\015 I turn on the dishwasher and it fills with water, then about a minute later it starts beeping and flashes le. Checked the wires and they seemed to be o.k..\015

Answers :

Hi,
le means locked motor disassemble the filter and work your way down to the macerator(steel chopper blade) remove it and see if the side labeled "this side up" is really up, its in english... dont think the chinese labourers paid attention to the warning cause i have seen alot that were wrong way

if it was installed correctly order the complete motor/sump assembly btw you do know LG d/w came with a 2 year warranty right? and some of the water distribution system had a longer limited warranty
read your manual, it states warranty, then price the part, then call warranty depot to ask them their service call and labour to install motor/sump


This part taken from a LG repair manual:
(Display Condition LE = Motor Error

Possible Cause For Error Occurrence:

Wiring connection is OK?
The Impeller of Washing Pump is
locked.
The rotor of Washing Motor is
locked.
The Blade is locked.


Remedy:

Check the wiring connection.
Replace the cause of restriction.
Replace the Washing Motor.
Replace the PCB.)
good luck.........
Repair Help & Product Troubleshooting for LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Kenwood KDW8ST2A dishwasher. We used to get the error code E3 (when still under warranty) and were told not to use dishwasher tablets as it generated too much foam. The problem has been intermittent but now we get the E3 error every time, no matter what program we run, or how little detergent we put in. I've a feeling its not heating up properly, is there any way to check the heating element? Is it worth attempting a repair?


... Kenwood KDW243A Builtin Dishwasher

I have an LG LDF7811BB dishwasher. Keep getting the "LE" error code. I have replaced the entire motor/pump assemble, main PCB, and both of the other PCB's still getting the "LE" error code. Was very pleased with the performance until this. Am I missing something?


Hi,\015\012This seems to be a very common problem withe these dishwashers. The LE error code (locked engine) is not allways indicative of a motor problem. Sometimes one of the gray wires which runs the length of the door panel was pinched and b ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Error code I keep getting an error code R02 on my Indesit DE 73 dishwasher, can anyone tell me what this means


... Indesit 24 in. DE73 Evolution Free-standing Dishwasher

Have a dishwasher with only model number i can find of DW009H. I am getting E6 error code and do not have a manual. Where can I get a manula ? who makes this dishwasher


... Dishwashers

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

Our LG Model LDF6810ST Dishwasher (2 years old) does not heat water any more. Dishes do not get clean and do not get dry. I do not get an error code. I assume I need to replace the control board OR heater assembly. How do I determine how to solve the problem?


It cleans poorly ------\015\012\015\012\015\012\015\012\015\012Water-inlet valve\015\012\015\012Most cleaning problems are caused by the dishwasher not getting enough wash water, so the water-inlet valve is often to bl ... Dishwashers

I have a Frigidaire 4000 Series Dishwasher, Model# FDB4315FCO, almost six years old. It acts as if there is no power. There is no error code. If I pull the power cord I get a "PF" message.


... Dishwashers

I have a whirlpool aquasteam 6 series dishwasher and no matter what cycle i run i get error codes f8 and e1


... Whirlpool Dishwashers

My brand new simens SR45M280SK dishwasher keep getting error code E21


... Siemens Dishwashers

The power is going to the dishwasher. The on off buttons work. No error codes. The salt light is lite (has been for 5 years) but now I get zero response when shutting the door (after selecting any of the 6 run options). There is no noise, no water, nothing happens. How do I repair this dishwasher so that it will run again?


Door switch failure. This will shut down all other start options. Inspect and possible replacement. See if you can activate it with something with door open. Give it a good close look... ... Dishwashers

ONCE AGAIN MY DISHWASHER IS DONE DO NOT WANT TO CALL A SERVICE TECH AGAIN HOW DO I RESET THE DISHWASHER FRONT PANEL TO GET RID OF ERROR CODES SERVICE TECH DID IT AND I WAS NOT WATCHING


... Samsung DMT300RFW Builtin Dishwasher

Dishwasher thermostat I am having a problem with my dishwasher as its not cleaning properly and not drying at all,am getting error code e3. I suspect the thermostat is faulty as have tested the heating element,I'm wondering though where is the thermostat fitted in this machine???


Usually on the bottom of the tub ... Dishwashers

I have an lg dishwasher mod#LDF7811ST, get error codeIE, changed the inlet valve, machine worked once then got IE error code again. Any suggestions?


If you are getting a IE or similar error on your LG dishwasher and have not been able to solve the problem using information based on that code, check the serial number of the dishwasher. If the first three numbers are between 501 and 702 you may ha ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Danby Dishwasher DDW1806BSL Dishes weren't getting clean for awhile. Now, we get an E3 error code and it won't continue through the cycle. There are no repair services in our area for Danby. Help!


Fault Codes E3: Longer heating time, but required temp not met. Possible Causes: Malfunction of temp sensor or heating element. ... Danby DDW1806BSL Stainless Steel Built-in Dishwasher

Getting error code 1E I've replaced the sump pump, cleaned the screen at the water inlet, checked water flow from the hose. Continue to get the 1E once water has entered dishwasher and begins the wash cycle.


... LG 24 in. LDS 5811 Built-in Dishwasher

What is error code E1? Dishwasher is not drawing in water on any programmes and this is the code I get


I get this a lot. Its due to a leak inside the bodywork, letting water build up in hte base and operating the float switch. You will have to pull out the dishwasher, tip it backwards and mop up all the water that comes out. (usual precautions about t ... Smeg DWI614 Built-in Dishwasher

Hi where can I get operating manual for Siemens ecosense dishwasher. recently bought property and appliance was already installed. Previous owner did not leave a copy and i now get E24 error code, with water remaining in base of unit - assume something to do with waste pump or pipe?!


... Siemens Dishwashers

I just installed a new Frigidaire dishwasher. Took it through 1 cycle as the directions indicate looking for leaks. I now have it full of dishes for its maiden voyage, and I get an Er uo code. Cannot find this error code anywhere. Can someone help me. M# FGHD2433KW Jamie


This is a vent problem you need to check the vent motor and make sure tha the wire have not been pinched by the door spring and make sure it is connected properly.the vent should be located on the top or possibly the right side of the cabinet. ... Dishwashers

DELONGHI DISHWASHER HI, we just purchased a Delonghi dishwasher DW67S/W and it reads Error code 4 which says that the inlet has been overfilled. How do we drain it or get it working? It wont allow us to do anything more. The store we purchased it from is closed so i cant ask them. Thanks for your help. Chocy


... Dishwashers

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

Im getting error code "LE" on my lg dishwasher


While LE is the LG error code for "Motor Error": The Motor is working\015\012abnormally, it does not always mean that the motor itself has failed.\015\012\015\012As you replaced the pump motor, are you certain that the Impeller of Washing Pump ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I get error code le on LG dishwasher.


Hi,le means locked motor disassemble the filter and work your way down to the macerator(steel chopper blade) remove it and see if the side labeled "this side up" is really up, its in english... dont think the chinese labourers paid attention ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1842 seconds