Having problems with your LG Dishwashers ?

Model LD-14AW2 alarms after 1 minute of startup and says E1


Answers :

The E1 error is telling you that there is a leak in the dishwasher. After confirming that there is no leak, even directly under the dishwasher (remove the kickplate and use a flashlight.)\015\012
\015\012After ruling that out, your problem is almost certainly caused by the drain hose between your dishwasher and your drain. There MUST be a 30" rise in the drain hose between the DW and the drain. If the hose just lays there, causing a siphoning effect (law of physics) that WILL drain water out of the dishwasher into the drain as soon as a wash or rinse cycle begins (after 1 - 2 minutes after they begin. Then the E1 error will be displayed.\015\012
\015\012The BEST way to fix this problem is to install an AirGap valve (almost free @ any hardware store) in your counter/sink and then running the short pipe to your disposal or sing drain inlet. If that is not possible or for a quick and dirty repair until you can install the AirGap, tie the drain hose to the bottom of the counter top so the rise is created.\015\012
\015\012Good Luck!
Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model LD-14AW2 alarms after 1 minute of startup and says E1


The E1 error is telling you that there is a leak in the dishwasher. After confirming that there is no leak, even directly under the dishwasher (remove the kickplate and use a flashlight.)\015\012\015\012After ruling that out, your ... LG Dishwashers

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kitchenaid Dishwasher Model KUDC25CHSS1. (Manual says KUDC25CH). The Delay Hours button is stuck on 2 hours. The manual says to cancel it, press it until no lights are on, but when we press it, the Child Lock light comes on. I tried pressing Energy Saver Dry to cancel the Child Lock, but that didn't cancel it. I tried turning off the circuit breaker for 5 minutes, but the same light(s) come back on when I re-set it.


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

The power went out and we cant use the reset button to get the alarm to go off. The error says 8. When the power went off it was not washing dishes and the door was not locked. Dish washer Model KDS-17A Thanks, Todd


I would try unplugging it for 30 minutes .. ... KitchenAid Dishwashers

I have a Maytag dishwaster model MDW700EDWG. When I start it is runs for about 2 minutes and then shuts off sometimes saying END. I have reset, re-powered etc. and nothing makes a difference. Please help!


... Maytag Dishwasher

Starts with UL when you unplug, does this for a few minutes then switches to china clean says 91 on the display and begans to flash every so ofter. After it does this the washer still does not come on it shuts down completely with nothing on the display screen. model FDB4315LFC3 any help would be great


... Frigidaire Dishwashers

I have a Whirlpool dishwasher model GU400XTPQ3 and it stays on the clean cycle and will not advance despite saying it has 2 minutes left? Please help. Thank you!


Important information about dishwasher cycles:\015\012\015\012\015\012Normal cycle time is anywhere from 1.5 to 3 hours long.\015\012\015\012A delay automatically occurs in some wash and ... Dishwashers

I have a fisher and paykel single door dishwasher model dw918 td. The other day its door spring collapsed and the door had a free fall. The dishwasher operated fine. But we have accidentally opened the door and let it free fall under its weight a few times. Last night the dishwasher began its cycle and stopped after 10 minutes - no beep, no alarm, display was fine. it just stopped. I opned and closed door a few times. Pressing the start/stop button only resulted in a beep but no action. I let


... Fisher and Paykel Dishwashers

Model GLD566 normal wsh and heated dry ledskeep blinging and every minute a small alarm goes off. I can't seem to reset it. help


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

I have a 2 year old dish washer, model GU2451. It stops in the middle of the cycle. It counts down to 44 minutes and won't count down any more. It sounds like a motor is running while the counter says 44. What is the possible problem?


... Whirlpool Dishwashers

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

The cycle is mistiming--it will start out saying 70 minutes, but 10 minutes later it says 29 minutes.


... GE Profile PDW7700G Built-in Dishwasher

I have a murray lawn mower powered by briggs and stratton, i'm trying to fing a manual on the internet but it says to put my model number, and on my engine it says that my model number is lev100 but nothing on the internet comes up, i need help. it also has a date (1995-1998). i don't know how many horse power it is.


The model numbers on a briggs engine are stamped into the metal cover above the spark plug and are the first 6 digits the rest are engine codes and type. ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

8 years ago we bought a model 665 Kenmore Limited edition Stock #575-0 if you need that. A certified kenmore tech. has been out here 3 times with still no clear answer. The problem is when you run a standard cycle of 95 minutes it counts down to 78 minutes and stays at that time for about 45 minutes then stars counting down again till 42 minutes then stops at that time for about another 45 minutes then coutinues till it finishes the wash and drying cycle. It runs and sounds fine the entire time


Sounds like timer prob.would rec. replacing timer ... Dishwashers

I have a Bosch model SHU43C02UC/47 dishwasher that will count down the time until it reaches one minute and then goes back up to 25 minutes. Sometimes a 125 minute cycle can take 180 minutes.


... Bosch Dishwashers

I have a fisher and paykel model 920 dishwasher. We went on holiday for a week and since then i have an alarm buzzer sounding intermittently and the display on the control panel keeps jumping


Possible there is MOISTURE within the unit or there can be cases in which some insects has clogged into the circuit board. You can open the panel board to check this out and even if there is no indication you can switch on the panel supply continuous ... Dishwashers

Mi T M Model CM-1250-A/C pressure washer shuts off after 10 minutes use. Wait 5 minutes and restart by pressing On/off switch. Shuts off again in 10 minutes. Works fine while on. Thoughts on problem?


I have one of these machines and it is VERY sensitive to line voltage. Be sure not to use an extension cord or the CM1250 will shut down. If you do use an extension cord use a very heavy one. The unit uses very close to the capacity of a 15A circu ... Pressure Washers

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Hi , i have westinghouse dishwasher model SB915SJ. when i put it to wash on eco normal, it stops a after about 20 minutes and i have to press the program button to start it working again. it's currently running now but it stops about every 4 minutes and the numebr 20 appears in the display screen. if i push the program button it will rung for another 4 minutes then stop, start beeping and the number 20 appears. how can i fix this?


Www.westinghouse.co.nz/...westinghouse/.../NZ_WH_Dishwashers_May06.pdf \015\012\015\012\015\012\015\012Above is your user manual, and below is your service and repair manual.\015\012 ... Westinghouse Dishwashers

I have a maytag dishwasher. The wash cycle runs for approximately 10 minutes, then shuts off. The timer will say 90 minutes +/- then will go to 1 minute and turn off? There is a grinding noise when the cycle first starts. Any ideas?


... Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

We have a Whirlpool dishwasher model ADG7550. It runs ok for a few minutes then it switches to the rinse setting (i.e. the furthermost left light of the temperature lights, i.e. lights from the left, 'rinse', '40degs', '50degs', '65degs', '70degs'. We may set it to start at e.g. 65degs, it does so ok for a few minutes then it switches to the 'rinse' light and starts to beep every few seconds. There are 11 beeps.


HI, There are two areas of concern here. This will be an issue with either the element, or control sector. I suggest to start with the element inspection. This will requir you use a multimeter, if possible. You will need to varify proepr element func ... Dishwashers

Dishwasher issues hotpoint dishwasher model HDA1200 used for a year and put into storage for a year. reinstalled this weekend. dishwasher was fussy about the door latch for a minute...door latch did not want to engage all the way...but went into its cycle. we stopped it and added a few dishes for a test run it started right up and ran about 8 minutes and shut itself down. it will not restart. the power supply is ok. no leakage about the door once latch engaged. what can we do?


It can be the 10A fuse located in the back of the machine. but.... storage is kind of a problem with determining what is wrong with it.\015\012Mouse can have chewed the wires, moisture can have rusted or corroded some components.\015\012C ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1099 seconds