Having problems with your LG Dishwashers ?

I am getting an IE error on my control panel. It seems to start ok but once it starts to fill with water the IE error comes up and the machine shuts off. How can I fix this?


Answers :

You do not list the manufacturer and model number, but it sounds like you own an LG dishwasher.

The IE error indicates that the water is not entering the dishwasher or it is entering too slowly / with little pressure. It is important to check the water inlet pipe (hot water connection under the sink) all the way to the dishwasher. Check for any kinks/blockages after you confirm that the valve at the sink is fully open.

Please report back here with what you find. If you still have problems, there are other things to check, including the solenoid valve just past the connection of the water inlet.
Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am getting an IE error on my control panel. It seems to start ok but once it starts to fill with water the IE error comes up and the machine shuts off. How can I fix this?


You do not list the manufacturer and model number, but it sounds like you own an LG dishwasher.The IE error indicates that the water is not entering the dishwasher or it is entering too slowly / with little pressure. It is important to c ... LG Dishwashers

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

Just installed bosch SHE68E15UC dishwasher today and during first cycle E15 error came up and unit will not go into another cycle or allow me to program anything else - sanitize and rinse aid lights are blinking - water went into the machine and it started filling the bottom and wasnt draining - i then adjusted the filter and the water drained - but e15 error persists - what should i do - is it install issue or machine issue - please help- thank you so much


... Dishwashers

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

Hi, Dishwasher problem: When a programme starts, the machine fills with water then stops and the "check water" light comes on. To empty the machine, I used the reset programme which does empty the machine. Any ideas of about what might be causing and the solution to this? Many thanks, Richard


You will need to check the inlet valve and the water level pressure switch. It can also be a low pressure in the pump that is giving out the signal for the control board to shut off.\012So first of all check the water line throughly to confirm. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

Maytag Quiet Series 100 fills up but washing cycle doesn't start. It drains the water and all but no water comes out from the jets. I can hear the electric motor trying to start, but it automatically shuts on its own.


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Water coming out front of dw at start of wash cycle. I leveled the unit. no luck. if you open the door during fill cycle the water does not shut off. also, may be a problem with float shut off working properly. what should I try next? Kenmore Elite 16579


Hi \015\012Check float to insure that it is free to move, it sounds like the dishwasher is over filling. That is assumed that you have not changed the type or amount of detergent being used.Also there is a probability tha ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

My lxi dishwasher drains more water than it fills during a cycle so after about three cycles the water level becomes to low. No error messages come up but I have to turn it off and refill it all the time. water pressure at the machine guages shows about 20psi when rinsing


There are two different styles of lxis one style has a drain diverter valve probably messed up some how something stuck in it not diverting the water to the wash arms and instead pumping right down the drain I am guessing this is your problem.There i ... Hobart 24 in. LXIH-3 Built-in Dishwasher

When the water should be filling or rinsing the machine is making a horrible, loud, noise and no water is coming out. The solutions I looked at for no water don't mention this noise - they mention a slight hum. This noise is as loud as a TV turned up almost all the way! This happened during a cycle - the wash ran fine and it got to the rinse and started this.


Hi,If the noise lasts beyond 2 minutes at a time (which it sounds like it does) then you have a motor problem. I am suspecting that the main seal has leaked onto the motor and is causing water to get into the motor. ... Maytag 24 in. MDB4100 Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

HAVING LEFT MY KARCHER B602 OUT OVER WINTER ,IT STARTED BUT LEAKS FROM INSIDE THE CASEING. TOOK CASE OFF AND FOUND PLASTIC PIPE HAD COME OFF PUT THIS BACK ON STARTED MACHINE AND PIPE CAME STRAIGHT OFF. WATER WILL FILL SOAP BOTTLE IF PIPE IS HELD ON WITH WIRE, BUT STILL NOT MUCH PRESSURE FROM GUN. ACN YOU HELP WITH THIS PROBLEM.


... Karcher Pressure Washers

Hi There, I have a frigidaire FDB1502RGCO dishwasher and I have power and water going to the macine however when I turn it on it will not start its cycle. Washing light is lit and all functions are lit up as normal on the front panel however the cycle does not start. Is there a simple fix or reset for this machine or will I need to call technical support to have a technician come to look at it? Please let me know. Thank you


... Frigidaire FDB1502RGC Built-in Dishwasher

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

Our garbage disposal was blocked and the dishwasher had filled with water because of the blockage. Now the disposal is fixed, but the water will not come on in the dishwasher when the cycle is started.


THERE IS A LITTLE FLOAT IN THE BOTTOM OF THE DISHWASHER THAT DETERMINES THE WATER LEVEL. mAKE SURE THAT IS FREE TO MOVE,RESET THE DISHWASHER TO THE BEGINNING AND START ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Model#lds5811bb--started making noise coming from the water inlet area(bottom left). 3/4's of the way through the cycle, noise became louder and then an error code "le" came on. We tried turning breaker off, then we tried in the rinse only cycle, but 5 minutes into it the "le" code error came on again. I'm fairly handy, so I'm not sure what part I can replace to maybe solve the problem. I can't afford to spend a couple of hundred dollars for a repair man to fix it. I'll appreciate any suggestion


The LE code is a locked motor code. Something may have gotten into the pump impeller. I would take the screens and filters off and clean the and check the pump for something stuck in it. It could also be the motor going bad but I would check the obvi ... LG Dishwashers

Our dishwasher won't start (model number 665.16049401). We had a similar problem last summer and a repairman came and fixed it. The problem was that the water level had gotten too low and so the machine locked itself off. This made sense as, at the time, I remembered filling the pool, running laundry and someone taking a shower all at the same time that I turned the dishwasher on. I am guessing this is the same thing that has happened now. The repairman put in a code and the machine worked. Can


Hello,\015\012\015\012ahhhh, you're taking about the reset sequence.\015\012okey dokie :)\015\012\015\012Here it is:\015\012Push the NORMAL WASH then HEATED DRY buttons in that sequence two to three t ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1567 seconds