Having problems with your LG Dishwashers ?

When the LG dishwasher come on it try to start then le flashes and it dost start what do i do


Answers :

You have a water fill problem.
Make sure the water supply is turned on.
Could be a bad water valve,bad wire bad timer,etc.

Copy and paste this Factory Service manual to help in diagnosis.
http://136.166.4.200/contents/Dishwasher/LDS5811/LDS5811_Service_Manual.pdf

It may not be specific to your model number,you did not post a model number.
It should help generically.
Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When the LG dishwasher come on it try to start then le flashes and it dost start what do i do


You have a water fill problem.Make sure the water supply is turned on.Could be a bad water valve,bad wire bad timer,etc.Copy and paste this Factory Service manual to help in diagnosis.http://136.166.4.200/contents/Dishwa ... LG Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start. I have already tried shutting off the breaker as suggested by someone but it did not solve the problem. Any other ideas?


Hi\015\012 \015\012Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks t ... Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


... Sunbeam Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


Hi\015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. Th ... Sunbeam SNB542UCAS Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Flashing lights My GE model # GHDA455L00CS Quiet Power a dishwasher's lights are flashing when I start it, will not reset or in-take water. I've tried unplugging it and restarting. Nothing. Tried removing door door screws and press down door latch. Still nothing. HELP!!!!!!! IT WILL NOT PROGRAM. IT HAS A FLASHING LIGHT. WE HAVE BOUGHT EVERYTHING BUT STILL DOES THE SAME THING


It mite be the circut board problem..just  re-soldered a few of the pins in it and things will be back in working order. ... GE Profile PDW8400J Built-in Dishwasher

Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit the start butt


... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Start light keeps flashing but washer won't operate. Tried to reset by hitting cancel button but start light keeps flashing.


Check whether inlet water is flowing into the machine. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Hi ,My Bauknecht dishwasher just beeps and the rinse option and the start button flash together. I can reset it by turning off and then holding the start button as I switch on but when I try to use it, it reverts back to the beeps and the flashes as described. washing pots is a bore, help me please.


... Bauknecht 24 in. GSX7551 Built-in Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Have miele dishwasher g641 inlet/outlet light flashing the water is going in and is draining starts flashing about 5/10 mins after starting do you know what else to try many thanks janet


Just encountered exact same problem - happened after attempting to clean very greasy pans so grease/oil created foam/more or less solid material in filter area, but as well in pressure switch (pn 4859640)\015\012This seems to be the cause (not ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Flashing lights My GE model # GHDA455L00CS Quiet Power a dishwasher's lights are flashing when I start it, will not reset or in-take water. I've tried unplugging it and restarting. Nothing. Tried removing door door screws and press down door latch. Still nothing. HELP!!!!!!!


... Dishwashers

Model 8573025-after being away for several months, I tried to run the dishwasher, and the lights started flashing, and it wouldn't start. Now it doesn't respond at all when I press the "normal wash" or "heavy duty wash" buttons, they will flash, but no other buttons respond at all.


When dishwashers get used after a long gap the seals dry out and start leaking or it could be moisture inside the switches. \015\012\015\012I will need the make and full model number of your dishwasher. Is it a Kitchen Aid? better to give ... Dishwashers

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

I have a Bosch Apexx. When I turned it on all I get a is flashing message "Not started". The LED display on the top edge is not working - only the display on the face of the machine. I have tried holding the start button and pressing all the other buttons and the same message keeps flashing...what to do?


Looks like micro-controller problem. Contact service center. ... Dishwashers

Allan Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start.


Turn off the power at the breaker to the DW and wait 15 seconds and then turn it back on and see if problem is fixed. Reboots the controller. ... Dishwashers

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0927 seconds