Having problems with your LG Dishwashers ?

I accidentally put Mr. Clean in my dishwasher where the Jet Dry is supposed to go. How do I get it out? i ran the washer and it began to foam up so the washer stopped and is flashing a repeating code HE then CL. Help!


Answers :

Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I accidentally put Mr. Clean in my dishwasher where the Jet Dry is supposed to go. How do I get it out? i ran the washer and it began to foam up so the washer stopped and is flashing a repeating code HE then CL. Help!


... LG Dishwashers

Frigidaire FDB126RBS2 Washer stopped working mid-cycle. Then a few hours later began washing again. Ran a load a day for another week before it happened again. It ran and stopped at Light Wash, then a few hours later started again and stopped mid-way through the rinse cycle. It has no power now and will not start again.


Be very careful, it sounds like an electrical failure, were the machine has cut out to protect you and itself. You need an expert there and quickly. Water and electric are a bad mix and more house fires are caused by washers than most other appliance ... Dishwashers

The dishwasher has the normal and economy wash lights flashing and after we hold the start button down for 4 seconds the stop and then return to flashing? The washer motor runs when the door is closed and no water comes out and the system doens't stop trunning until the door is opened. The system ran for over 4 hours yesterday. Viking Professional


Hello, welcome to ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

My whirlpool ADP 8540 starts, fills, then stop and flashes 6 times, pauses, and flashes 6 times repeatedly, until I end the cycle. What is this error code for? Can I fix it myself?


6 Flashes means water valve is switched on but flow meter senses no impulses (less than 10 impulses in 10 secs) and the water indicator is at a low level. Water Valve Closed or blocked.\015\012\015\012Water inlet valve defective. Flow met ... Dishwashers

Coleman mobile home furnace...Model number DGAA077BDTB...The furnace about a month ago started going out ( flash code- Combustion Air switch stuck closed)We replaced the thermostat on the wall and it stopped doing it and ran fine then last night it stopped again ( Combustion air switch failed to close) and when i got up the furnace was working and now for the past few hours it refuses to do anything...I am on a very very tight budget...and need some idea of what is wrong and do i need a professi


I had the same errror code on my coleman furnace (3 flashes combustion air switch failed to close) but at first didnt realize there was even a light that gave codes..Anyways long story short, after searching many forums one guy mentioned about the fu ... Dishwashers

Hi there, I have a Whirlpool DWF A00, A few mins after I turned it on, it stopped, drained the water and the ON-light started flashing. It flashes twice, pauses for a sec and then repeats. I searched the net, but could only find other dishwashers or other light-codes. Please Help! Thank you Michael


... Whirlpool Dishwashers

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

My asko dishwasher ran great until recently. after finishing a load, the pump just continues to run (even when all water has been pumped from the unit and it's running dry) and the display isn't flashing anything (not codes, etc). Worried about destroying the pump, I shut off the washer at the breaker, and it's been a few months since we've had a dishwasher. Every once in a while I'll turn the power on and it just continues doing the same thing - it's stuck in this position/state, so I have to s


The IC that controls the pump seems to have gone kaput. Change the IC. ... Dishwashers

I have a Kenmore Ultra Wash model 16879. After setting the dishwasher and going to bed I woke up to find the "Quick Rinse" light flashing. I am unable to get the light to stop or washer to work. I tried some of the "code" combinations I saw offered on fixya but I do not have a heated dry button, and cannot find another combo that works. Thank you for any tips you can provide.


1) Crack the door open.2) Within 3 seconds press the \015\012following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy \015\012Saver Dry3) Close and latch the door4) \015\012Press the cancel button (the circle with ... Dishwashers

Hi, My IGV645.1 kuppersbusch dishwasher has stopped working halfway the washing cycle. It is beeping, and the start led flashes repeately two times. What does this code 2 mean? Regards, Koen


... Kuppersbusch 23 in. IGV6435 Built-In Dishwasher

MAYTAG 3000 SERIES JUST RECEIVED AN F20 CODE. WHAT DOES F20 MEAN? THE MECHINE RAN FOR 10 WASHING THE STARTED STOPPING ABOUT 10 MIN IN TO THE CYCLE WITH F-20 FLASHING.


Need the correct model # and ser # _ _ _ 3000 _ _ _ _ this tell us age and and fault codes . now inside the machine / you will find a tec sheet with the codes . this may be quicker .. mm ... Dishwashers

Frigidaire dishwasher Model GLD2250RD50: Stopped washing dishes when a ran the garburator full of water, panel lights of high temp and nearby started flashing, then I pressed cancel/start, lights went out the washer wont run, checked breaker no problem. door latched,


... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Whirlpool model du1100xtpq6 machine will not start clean lite flashes 7 times stops and repeats must be code 7 blinks only drain pump runs when drain/cancel button pushed


Hi, this is an indication that the water did not heat properly. Follow this link to some instructions I put together to help solve this and reset the control so you can use the machine again. ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

We have an Asco type DW 95.5 built-in, model 1885. During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric still runs. When I pop the circuit breaker, all is stopped. However, when power is restored, the lights and code flash as above, and, again, something electric runs. My email: [email protected] Thanks for any help...


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description " During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric s ... Asko Dishwashers

Water fills washer, program stops, inlet/drain flashes. checked all filters and pumps for blockages. none found. try again and washer empties water, then fills up again, program stops, inlet/drain flashes again. could it be a fuse???


Could it be.Try to open and look the fuse inside.Opps try to see the warranty of applian. ... Miele 24 in. G692SC Plus SS Free-standing Dishwasher

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

My Dishlex global 300's rinse light is flashing after 5 mins use. About 2 inches of water stays at the bottom of the washer. Bought this second hand and it has not been used for a few months. Do I need to fill the reservoir under the washer or lean it at 45 degrees to dislodge anything in the sump. If you have had the problem of the washer starting its program and then stopping after 5 minutes and the rinse light flashing I would appreciate your advice. Cheers Hyph


The flashing rinse light is an error code. I am assuming that your control board is good because the lights are working. I'm also assuming that this model has two pumps. One for filling and one for draining. The rinse light flashing is probably i ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the message. Push reset button and washer starts back runs a couple minutes and then stops and then beep and gives the same message on control panel "washer arm blocked" again. There is "NOTHING BLOCKING" the washer arm!


The rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so \012\012\012\012check the jets for blockages... you might have to remove the arm to clean them properly ... Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Whirlpool ADG7540 approx 4 years old (maybe a bit older) I have ran diagnositic check and the start light flashes 4 times stops briefly then flashes 4 times again over and over along with a continuous bleeping. When I put the dishwasher on any program I can hear the pump running but after a few mins the same flashing and beeping occurs although it sounds as if the pump is still running. I have taken off the pump checked for blockages and also checked the outlet hoses and spiggot, there are non.


Yikes, we have just identified this exact same problem tonight. If you've had any success with fixing it, we would sure appreciate hearing how. Best of luck with your machine ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

Hi i dont know the model of the dishwasher.. but the controls are fairly staright forward... a little knob for temperatur control and an on/off button.. and a light that lights up green when dishwasher is switched on... now the problem is as happened recently, when you switch the washer on greenlight is on and washer can be heard doing something but after a minuit or so the washer stops and the green light flashes. open up the dishwasher no sign of water or that it has done anything at all... th


It sounds like your washer is not getting enough water to start. If your washing machine is filling too slowly or not at all, then you probably have a clogged screen on the back of your washer. To check this: \015\012\015\012 ... Whirlpool Dishwashers

New pressure washer has started and ran for about 1.5 hours. After it ran out of Gas, refilled and now it runs for about 2 min then stops. Its the same gas that was used when it ran for 1.5 hours. Any ideas?


New machine... there are a few of things to check.\015\012\015\012First off re-check the engine oil level. The engine has an oil level sensor and will shut off the engine when it senses a low oil level. \015\012\015\012Then w ... Psi Blue Max 2200 High Pressure Gas Power Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1525 seconds