Having problems with your LG Dishwashers ?

I have a Teka lp700 dishwasher.When i select a program the dial won't move through cycle automatically.do i need a new machine?


Answers :

Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Teka lp700 dishwasher.When i select a program the dial won't move through cycle automatically.do i need a new machine?


... LG Dishwashers

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

10 year old Kenmore Ultra is leaking early in the washing cycle. Wondering if this is worth fixing or need to bite the wallet and buying a new one. I am worried about affecting the new cabinets even though the dishes seemed to be clean on the two occasions that the dishwasher has leaked. Only need a somewhat simple machine- I'd appreciate any suggestions as to what brands I should research if buy is the conclusion. Thanks.


At 10 years old I wouldn't put much if any money into it. Do check the water connections as it may be something simple that just needs to be tightened or a washer replacement. Replacing the valve is a simple and inexpensive fix but don't bother going ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I need the steps to change the hose assembly on my Whirlpool portable dishwasher. When I got it someone had cut the sink connections off so my son connected it to the water and drain with my washing machine which was in the kitchen. However, I have moved and want to use it as portable. I purchased the new hose assembly for the sink faucet, I just need instructions on how to take the dishwasher apart and connect the new hoses.....HELP PLEASE!


... Whirlpool 24 in. Portable Dishwasher Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have an ignis dishwasher by whirlpool and it seems stuck on the rinse cycle - it wont move on and the machine is beeping non stop. I have switched the machine off several times and unplugged it but it still lights up on the rinse icon and is still beeping and I cannot move it on


... Dishwashers

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

Hi. My dishwasher won't let me move the latch into the locked position. When I turn the knob past the start cycle I hear a klunk noise. When looking at the latch it is obvious that there is a gold color piece of metal on top of and in front of the silver latch blocking it from moving sideways. Is this something I can fix on my own, or need a repairman or time for a new washer? The washer will be 5 years old in October. Thank you, KIm Martinez


... GE Nautilus 24" Built-in Dishwasher

Telmann dishwasher We have just moved into a new house with a Telmann TEL12DWMS dishwasher. The dishwasher will light up but wont start. Power and Rinse cycle lights light up but when you turn the dial it wont start. Any suggestions? Thank you


... Dishwashers

I am an Australian who has bought a second hand Defy Dishmaid dishwasher from a South African work mate. It is a 2/3 year old machine that he bought over from South Africa. When he moved into a new house the machine did not fit his kitchen bench opening much to his frustration so he sold it. When placed in my kitchen it was a tight fit and upon recent inspection the floor pan of the unit, it may have buckled. It worked well until recently when we did some renovations when I needed to remove


Hi\015\012\015\012This means that the dishwasher is unable to drain water completely, you can run your washer at\015\012its hottest temperature setting with 3 cups of vinegar inside the unit. After\015\012this take off ... Dishwashers

We put in a new garbage disposal and now our dishwasher wont workit starts each cycle we suggest, but the water does not run and the cycle does not move forward


Hi, \015\012\015\012Does the drain hose for your dishwasher connect to the disposer ? If so, has the knock out for the drain tube in the disposer been "knocked out" ?\015\012\015\012Check that and reply. We'll move forward from there if need be.\015\ ... Bosch 24 in. SHU43 Built-in Dishwasher

CSD69 slimline dishwasher Water in machine wont drain. machine won't start on prerinse, just makes noise then moves on to wash cycle and prerinse light stays on, no water being let in either.


... Candy CSD69S Built-in Dishwasher

Holding water There is water in the bottom of the machine after the cycle is done. There is definitely draining going on throughout the cycle, but it's not draining completely at the end -and the water that is left is murky. Spoke to a friend who tells me it sounds like the dump valve, but in checking on line, that doesn't seem to be a part that even exists any more. Do I need to buy a new dishwasher? This was not in the budget this year... Thanks for any advice! Nancy


Are the dishes getting clean at the end of the cycle, if not then there could be foreign debris in the pump housing that can cause this, needs to be dismantled and cleaned out, if dishes are clean then the pump impeller will need to be replaced ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Bosch she44c06uc. Like many here, changed out the garbage disposal and didn't drain. Have reset the system by holding the "Drain Cancel". No help. The cycle stops at draining. Investigated and found small piece of glass wedged in the impellor. While having the interior cover over the impellor off, the motor for the drain impellor is humming, but the impellor does not move while engaged. The impellor will rotate by hand and stops at a point at 3/4 turn. I am hoping it is not in need of a new moto


Check the center of the impeller, it should be flat on one side round on three, the impeller might be rounded out from the shaft it sits on. You might just need a new impeller. Good Luck, N let me know Thanks. jimmy ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I think I am finding small pieces of the wrap from the tablets in the small holes in the spray arms, one wont move anymore??? This is about 10 yr old maytag machine. I tried to clean out the spray arms but dont really know what I am doing. Bought a new diswasher, dont want to use the tablets if they will clog up the works. please advise.


Just prime the sink before you start the dish washer ... Maytag Jetclean II MDB8551A Dishwasher

Beko dsfn1530b wont start cycle all lights up but nothing happens has been moved while new kitchen fittedand worked fine before this


... Beko Dishwashers

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

My d1716 continues to run, but does not move forward in the cycle. I can even open the door and it continues running. If I didn't unplug it, the motor would likely burn out. Do I need a new dial? Thanks.


Hi\015\012\015\012I would suggest that your flood switch has been activated. There is a float on the bottom plate or base plate of the machine. If there is a water leak, the float rises and triggers the flood switch.\015\012\0 ... Asko D1716 Built-in Dishwasher

Once the "start" is pressed, the "reset" option on the same button will not turn it off. This dishwasher is in a new place we're buying, and we're not ready to run a whole cycle to see if the machine works because there's a minor plumbing repair needed under the sink which can't be done till the closing, and there could be a leak. Meanwhile the two green lights and beeping can't be turned off.


Just un-plug it for now,....then of coarse when you can run it plug it back in for test,....ya never know, just un-plugging it could very well reset itself and work fine. this is the way with alot of the newer things,....good luck ... GE GLD5800L Dishwasher

I purchased a NEW Whirlpool dishwasher from Appliance Direct in Daytona Beach FL. The dishwasher was delivered broken. It needs a new motor pump. I asked for a new machine and they said it's their policy to fix a machine that's been delivered. I think I have a lemon. It's been a month now since delivery and they haven't even repaired the machine. Do you have any advise on how I should proceed? Glenda


You must go with the fact and hold the company accountable. 1 call speakto manager get his name and direct #. give him 3days to resolve the problem. ask him will it be repaired monday or teusday because both of those days are convinent for you.then f ... Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1731 seconds