Having problems with your LG Dishwashers ?

I have an LG dishwasher, Model LD-2120WH and lately it starts" -- water goes in but it throws up a E1 message on the display screen, send off an alarm and stops


Answers :

I've just solved the same problem on my 2120. It started when the pump motor bearing failed and continued after I'd replaced the bearing. According to my handbook the E1 fault is theoretically a water leak but practically it is that the pump is not delivering enough water. In this case the failed bearing had allowed the shaft to wobble about and damage either the rotor or the inside of the pump (it's sealed so you can't strip it). Solution was to replace the pump.
\015\012
\015\012Paul H
Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an LG dishwasher, Model LD-2120WH and lately it starts" -- water goes in but it throws up a E1 message on the display screen, send off an alarm and stops


I've just solved the same problem on my 2120. It started when the pump motor bearing failed and continued after I'd replaced the bearing. According to my handbook the E1 fault is theoretically a water leak but practically it is that the pump is not d ... LG Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

We have an LG dishwasher model LD-12AW2 that randomly goes into alarm tone & displays "PE" on the display. what is the problem??


... Dishwashers

Hi , i have westinghouse dishwasher model SB915SJ. when i put it to wash on eco normal, it stops a after about 20 minutes and i have to press the program button to start it working again. it's currently running now but it stops about every 4 minutes and the numebr 20 appears in the display screen. if i push the program button it will rung for another 4 minutes then stop, start beeping and the number 20 appears. how can i fix this?


Www.westinghouse.co.nz/...westinghouse/.../NZ_WH_Dishwashers_May06.pdf \015\012\015\012\015\012\015\012Above is your user manual, and below is your service and repair manual.\015\012 ... Westinghouse Dishwashers

Hi . I have a Zanussi DE6965 which has started displaying the error message AL6 every now and then. When it stops and shows this the water has not pumped out. If you turn it off, leave for half an hour or so and turn back on it sometimes works fine to the end. Sometimes it stops again. Eventually after several stop starts it works through. Any advice what could be causing this? Thanks.


... Zanussi 24 in. DE6965 Built-in Dishwasher

I have a fisher and paykel single door dishwasher model dw918 td. The other day its door spring collapsed and the door had a free fall. The dishwasher operated fine. But we have accidentally opened the door and let it free fall under its weight a few times. Last night the dishwasher began its cycle and stopped after 10 minutes - no beep, no alarm, display was fine. it just stopped. I opned and closed door a few times. Pressing the start/stop button only resulted in a beep but no action. I let


... Fisher and Paykel Dishwashers

Kitchen Aid Superba Selectra 21 Mod.: KUDS21SS1 MS S/N: FE 84757436 After whole house power outage, dishwasher began constant high pitch beep or whine. Machine controls unresponsive; display shows F. Cycling power has no effect {except noise stops and display goes off when powered down - of course). Any troubleshooting and parts availability advice would be greatly appreciated!


... KitchenAid Dishwashers

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

My deceased parents have a GE dishwasher (don't know the model number - can't find it on the machine and can't find the paper work) that stops working shortly you start it and displays a message on the front panel that says "Blocked wash arm - check for wash arm obstruction - restart". We restart it and get the same message shorty thereafter. This happens when the washer is COMPLETELY EMPTY, even when we remove the bottom rack. It first started after several month of inactivity. We'll just t


Could be false sensor input, could be that the arm is not turning, I am not sure how old your machine is, but age could play a part if the arm is "in fact", not turning. If you are not mechanically inclined, I would suggest that a qualified repairma ... Dishwashers

Westoint Dishwasher I have looked in the manual under troubleshooting tips, but didn't find anything on the problem. The dishwasher goes into cycle,but during the wash cycle it stops,makes alarm and the wash and rinse ligts come on. And now I can't even find the product on this site.Westpoint Dishwasher WQP12-9240. Thankyou My dishwasher is stopping at stage 2 of the programme after beeping once. Quite often the detergent flap doesn't open. Am at my wits end and threatening to leave home!!!! Th


Hi again,\015\012\015\012That should be OK. Just get in touch with your sales rep or his boss. Somebody there will be able to look up the record of the purchase. If they ask for model & serial numbers, you have them. You will find ... Dishwashers

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

Calypso washer display "FD" perhaps meand full drain and can't reset and just stop. I run washer with back cover out to see that while water doesn't fill up the drum but normally agitates and just fill up the water reservoir to full and don't drain out to sewer and washer just stops with the message "FD"


Peace broohilda,ngafm At your service!With an error code the only way to find and to repair this is,First unplug the washer and wait a few minutes then restart it like rebooting your computer when its acting strange! ... Dishwashers

Stops working half way through a cycle and alarm goes off


How many beeps does it make ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

E1 comes up on screen and alarm goes off, how do I fix it?


Leakage error > Condition: Excessive RPM of washing motor happened \015\012during wash cycle due to water leakage.\015\012Possible cause: Water leakage in hose connections,water is leaked by \015\012damages. The motor water seal leakage of sump as ... LG LDS4821WW 24 in. Built-in Dishwasher

Error code Dishwasher has an error message of 1E. And an alarm goes off. It does not start.


The unit did not reach it's full fill level after 10 minutes.\015\012Check that water is not siphoning out as quickly as it fills. The drain hose must go up and attach under the counter top or go through a hole in the cabinet at, o ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Hi, I have an AEG oko favorit 64800 and when I turn it on and select a program it doesn't work. The power light comes on and the digital screen comes on but it looks like this -- --. I try to press the buttons to select the appropriate program but nothing happens. There is no alarm code displayed in the digital box. Thanks Louise


... AEG 18 in. Favorit 64800 Free-standing Dishwasher

I have a Frigidaire Series PLD2855RFC3 dishwasher. Near the end of the cycle the dishwasher stops and begins flashing "PF" on the display and the lights for "Hi Temp. Wash" and "No Heat Dry" also flash. I know "PF" = Power Failure, but the power never goes out... so what is causing this error and disruption in the cycle?


... Dishwashers

I have a LG intello dishwasher 2050SH Turned it on yesterday and did a rinse. This was the first use for 4 months in our second home. It was very cold. The rinse stopped some way through and an error message displayed (cannot remember). Tried to run again and now the dsiplay is locked. It turns on with usual sound, but none of the buttons work. They make a noise when pressed but nothing on the dsipay changes. I suspect that the outlet was frozen and that I should not have tried again - too im


Hi\015\012\015\012To\015\012unlock the lock in your LG Dishwasher, with the door open press the SPRAY &\015\012RINSE buttons simultaneously for 15 seconds. Hope this helps...please post back fo ... Dishwashers

I have a PLD3460RDC1 dishwasher.The power got shut off and it now displays an ER message with all the other lights blinking.I have shut off the power to the unit many times, first getting a PF error and then it goes to the ER with all lights blinking. How can I reset this?


HI, there has been a power surge/pulse, that has been absorbed by the electronic control board. There may be serious damaged here, in this case. You can try to reset the main logic chips by unplugging, or shutting power down for five minutes. If the ... Frigidaire Dishwashers

Please help my wirlpool ikea diswasher was working well but suddenly it stopped!I have one of those DWF small ones and have the buttons on the inside top part of the door. when I press the start button nothing happens and when I close the door the alarm sound goes off!! can anyone help me please


Try dropping power to the unit for a minute and see if it will reset itself. if not, you have a logic board failure. that or a door switch. check the manual for an indication on the warning alarm.good luckmark ... Whirlpool GU2400XTP Built-in Dishwasher

ASKO dishwasher my dishwasher came on spontaneously and keeps running first (drain, I believe) cycle. It stops when I unplug it (of course- no power) but sturts immediately when I plug it back. Error message is displayed


F2 fault water in the base remove dishwasher from under the bench and tip back water will run out,then it will restart.remove rear lower panel and run the dishwasher you may find a leak,also check that the inlet valve is shutting off and not filling ... Asko D1776 Stainless Steel Built-in Dishwasher

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

Model G2582 SCVi We have F70 fault displayed. Have turned off water supply but drain pump continues to run even with machine supposedly switched off. Is there a way to stop as it will take 3-4 days to get a service engineer here. Note can't simply throw a switch in fuse box as this also takes out multiple other power ponts


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1066 seconds