Having problems with your LG Dishwashers ?

LG dishwasher LD1415T cuts out after 5 minutes,suspect PCB?


Answers :

Hi,
\012I think you are on the right track, but before changing it I would check to make sure that there is no electric coming out of the board to like the motor, to make sure that the motor is not getting hot and stopping...
\012You could do that by having the front kick cover off and when it quits then use a meter to check for power at the motor...no power board bad...
\012
\012heatman101
Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

LG dishwasher LD1415T cuts out after 5 minutes,suspect PCB?


Hi,\012I think you are on the right track, but before changing it I would check to make sure that there is no electric coming out of the board to like the motor, to make sure that the motor is not getting hot and stopping...\012You could ... LG Dishwashers

LG dishwasher LD1415T cuts out after 5 minutes,suspect PCB?


The printed circuit is the cause of that I am sure, to replace it you must take the door apart as the board is sandwiched in between remove the screws that hold the door apart and carefully remove the connector from the old board DO NOT PULL ON THE ... LG Dishwashers

I have a diplomat adp8332 integrated dishwasher showing an F3 fault code.I dismantled the door casing and found that the wiring sheath had split and cut through 2 wires.I have repaired the wires and fitted a new sheath,the F3fault code still appears(no heated water and only rinse cycle)Could the PCB have part blown or the heating element?


... Dishwashers

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch 24 in. SMU40 Built-in Dishwasher

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch Dishwashers

My portable dishwasher hose that attaches to the faucet is to short for where I want my portable dishwasher to sit. I would like for it to sit in one spot. I am not allowed to alter or cut holes in the side of cabinets, I am renting. Is there an extension for the hose to the faucet? If not, what can I do to make the hose longer? If I really have to I will cut the two hoses that comes from the dishwasher to the faucet, but I would rather have an extension first.


You should be able to find extension or replacement hoses that you can use to extend the existing hoses at a hardware store. If you need to join two hoses that have female connectors, adaptors with two male connections are available. ... Dishwashers

KUDS30IXBL My dishwasher stops mid cycle. Technician said it was too many suds and cutting off. I use cascade and jet dry and nothing else. There has been no other soap in the dishwasher. After it cuts off on normal (soap dispensed) I restart on light/china with no detergent. Sometimes it runs through with no problem and sometimes it stops with all lights off. Any suggestions? I have already had technician out twice for other problems with this dishwasher that is only 2 years old and don


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Westinghouse Silhouette 906 dishwasher cuts out after pre-wash, sometimes goes through cycle to rinse, then cuts out. Obtained service from sole dishwasher technician in Ballarat - he was very discourteous, claimed to have corrected fault, charged $125.00. Fault not fixed - that was many months ago but don't want him back. Please advise


... Dishwashers

LG - LDF7811ST Dishwasher will not turn on at all. I have replaced the main PCB board and checked all wires for shorts. The PCB board does have 120Vac to the board. I have also checked the latch and it does close the switch when the dishwasher is closed. I think it may be the main switch/power button board but can't seem to find the part number or alternate part numbers that can be used.


Hi. The likely culprit will be the power switch. The part number for this switch is 5020ED3011A.NOTE_ Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for po ... Dishwashers

Leaking Dishwasher seems to be leaking. Otherwise it's performing fine. I have laminate floors, and there are water seeping out along the seams of the flooring area near the dishwasher. The dishwasher is captured by the floor (dishwasher was installed first then floor was put in at 1/2" higher level), so we can't pull it out to check where the leak is coming from. Can dishwasher be repaired from the inside w/out removing it from where it is? Only way to pull it out seem to be cutting a part of


This is a huge problem for you. when you have a leak coming from the bottom of the dishwasher the machine will have to come out. but first check the door gasket to make sure the leak is not coming from there. ... Jenn-Air 24 in. JDB4950 Built-in Dishwasher

Hi In the middle of a wash cycle, my dishwasher tripped the circuit breaker on the wall. I diagnosed this by unpluggin dishwasher, plugging in a different appliance and switching circuit breaker back on. new appliance worked OK. When dishwasher had cooled, I tried it again on same circuit (which I knew was working properly). The lights came on for about three seconds, and then the circuit breaker cut back in again, so I knew it was the dishwasher that was causing the problem. Is there anyt


Ck the connections where the cord hooks to the wiring harness. look for hot or shorted wiring . also ck the contro panel for the same . generaly if you have a power draw like you are saying then you can see t ... Dishwashers

Beko slimline DE2541F. Left dishwasher washing dishes and went out. While we were out we had a power cut and now the drying fan won't switch off. Dishes are clean and dishwasher empty but fan s


... Beko DE2541FW 18 in. Portable Dishwasher

Hello, We have a combination oven and dishwasher. Last week I filled up the dishwasher and after about 5 minutes a blue spark came out at the bottom and it cut the electricity off. Once the electricity was restored we started it again and after a few minutes it just stopped after filling up with water. It blew a fuse again but only one fuse this time and now doesn't switch on anymore. We have emptied all the water from the dishwasher and checked the filter, etc and wonder what could have gone wr


Hi, I contacted the Rosieres web site in France and sent a message using the link Contact Us. Here is the reply;Dear xxxxx,we advice you to contact:TELE MENAGER VIDEO SERVICE21 rue georges Doublet0610 ... Dishwashers

I have a DS605 and DD605, F1 fault comes up everytime I try to cut the dishwasher on also water will emerge in it and the impleller floats up under the rack on the top dishwasher. Both dishwasher comes on the same time and make noise and the F1 with a little rench shows up. They said when the red light comes on the salt reservoir is empty. What kind of salt do I put in.Please advise


... Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

Hi I have a Jenair JDB1090AWS Dishwasher, that seems to be in locked mode (flashes 5 times when I press the start buttom). I tried holding the Heated Dry down for 3 seconds like it says in the manual but nothing happens. I even cut power to the dishwasher for > 30sec, still no joy. The dishwasher is still locked. How do I unlock it? Chuck Olson


Hello Chuck,. When these appliances work like they are supposed to they are great....... that being said lets see if we can unlock your dishwasher.\015\012\015\012Since the heated dry button doesn't unlock it, lets try the energy saver ... Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Hi. I had f1 appear on my Gisher and Paykel dishwasher. Unplugged from wall. Few days later dried using a hairdryer. Took cover off pcb board and dried in there as well. There was water on bottom of cabinet so understand the F1. Problem is now, I put cover back on pcb board and tried to power up but it is dead? Any sensor.microswitch on PCB cover, or anything i may have missed? No power at all to unit? Any assistance greatly appreciated. PS - Wall socket finer as powers other appliances.


Wait.................. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher Fails to drain and cuts out via float switch?


Hi\015\012Dishwashers are usually protected from overfilling by a float switch. This switch is located in the bottom of the unit. Here's how to check and replace it:Step 1: Open the door and remo ... Beko 24 in. D3421F Free-standing Dishwasher

Bosch compact Logixx dishwasher (8401) will not start after it did turn on to start a cycle. Pump made laboured draining noises then seemed to cut out. Water remains in the bottom after last cycle.


... Bosch Dishwashers

Diplomat Dishwasher motor cutting out on hot mid cycle


Hi ,This problem is your main wash motor the origonal is an ascol\015\012 motor ,but the replacement is a motor with copasiter costs\015\012 around £80.00 for new motor ... Dishwashers

Dishwasher not draining after a power cut


I would run the heated dry cycle a few times to try and get rid of that residual water, then restart the cycle and see if it work now. If it still is a problem try cleaning out the drain line behind the dishwasher, this is a very common problem with ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

LG LDF8812ST dishwasher not washing: reports LE error code. Fills and drains ok. Impeller is clear, removed inside housing - no obstructions. Synchronous motor works. Tested main motor - appears to be good. Motor is not locked, looks to be in excellent condition. No shorts to ground, continuity across three main pins - not sure what the other 4 are for. My guess would be the PCB, but not sure how to test this. How do I determine if the PCB is bad?


... LG LDF9810ST Built-in Dishwasher

I have a bauknecht dishwasher....I had a power cut now an alarm is going off in the machine How do I turn it off and get the dishwasher working agaian?


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. Please switch off the Dishwasher and disconnect the power supply from and to the Dishwasher from the mains and the\015\012power socket and re conn ... Bauknecht Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1822 seconds