Having problems with your LG Dishwashers ?

I have LG dishwasher for 2 years now. Working perfectly until one day one glass gets broken during washing cycle. Immideatly we get EO error. We check possible reason of error in the manual then decided to try to fix ourself. We open bottom cover and drain outcoming part. Immideatly we discover a piece of glass that was preventing a small plastic piece to rotate. We remove that piece of glass. Put back covers and machine. We connected it back to outlets and run it. All was working again !!! This


Answers :

In order to fix problem we disconnected dishwasher, put it on one of side, opened bottom cover - the one that is outside of dishwasher. We find out the part that is
\015\012connected to the drain horse. We take of 3 screw and open that part too. We discover
\015\012few small peices of glass that were preventing to rotate one plastic part of dishwasher. We removed that pieces of glass. Put all back and connected dishwasher. All was working fine. I am suggesting to everybidy try these steps before calling for any service.
Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have LG dishwasher for 2 years now. Working perfectly until one day one glass gets broken during washing cycle. Immideatly we get EO error. We check possible reason of error in the manual then decided to try to fix ourself. We open bottom cover and drain outcoming part. Immideatly we discover a piece of glass that was preventing a small plastic piece to rotate. We remove that piece of glass. Put back covers and machine. We connected it back to outlets and run it. All was working again !!! This


In order to fix problem we disconnected dishwasher, put it on one of side, opened bottom cover - the one that is outside of dishwasher. We find out the part that is\015\012connected to the drain horse. We take of 3 screw and open that part too ... LG Dishwashers

I have an Ariston LI45. The stupid thin one. It's not seen much work & is just out of Guarantee. It's stopped working & is showing 2 flashing lights. Stops partway in to a cycle with water in the base, but not enough to cover the element. Tried re-setting, no difference. I have also noticed that it's melted a plastic wheel off the bottom tray at the back. After reading problems with other washers, i'm guessing the water level switch & maybe element too. If this is the case, i'm ok finding the


... Dishwashers

Hey Everyone! Ok try this one! I have been working on a KUDS25 Kitchenaid Dishwasher. It was leaking like a siv from the bottom. I replaced both top and bottom plastic bearings and also tightend all the screws at the bottom. Leak Gone, I thought. It now has small leaks down both sides. I have since been told by the owner that he took the door apart himself. I pulled out the dishwasher from the cabinet and ran it. I could see the leaks at the top on both sides of the door latch. I cou


Hello davidgalb. You can install a new gasket to seal the door again. That old seal is not flexible any more. That said, for my time and money I recommend a replacement dishwasher, this one has definitely seen better days. Joe ... Dishwashers

We discovered broken glass dish in bottom of dishwasher with some pieces below the bottom pump area. Shortly after the washer is making a louder noise during operation time. The water pump is quite when filling but after fill the noise comes during the wash time. The heat element works fine. What can be done to quite the wash cycle????


Sounds like you have broken glass in the wash pump you will have to remove pump from sump and clear also check the drain pump.good luck let me know how it goes ... KitchenAid KUDK03ITBK Built-in Dishwasher

We have a Fisher& Paykel dishwasher with 2 drawers -- one on top of the other. Model DD603. The bottom drawer works fine. But the top drawer is not working properly -- it repeatedly stops in the middle of the cycle and there is water left in the drawer. Previously when this happened, we called a repairman; he removed the top drawer from the machine, said it was "off track", flipped some lever, and put the drawer back. He seemed a little embarrassed by having to charge for a service call for


Are you able to provide a bit more information on what you see when the dishwasher stops in the middle of the cycle -\015\0121 - is it displaying the time remaining in the cycle and is it always the same time?\015\0122- do you get any fau ... Dishwashers

I have a kenmore quiet guard standard dishwasher. About 2 weeks ago it started leaking. today I pulled it out and found that looking straight ahead at the door on the lefthand side under the bottom is 2 small wire metal fittings that screw up into the bottom of the dishwasher. one was loose and dripping water. when i screwed it back in i noticed that it was stripped out. can it be replaced or should I scilicone around it to stop it?


... Dishwashers

I have a Whirlpool dishwasher DU800CWDB4. Two plastic pieces ended up on the bottom of the dishwasher one day. I have determined that they are the upper 2 pieces of the lower spray arm tower. I can't figure out how to get them to fit back on correctly.


... Whirlpool 24 in. DU800CWD Built-in Dishwasher

I recently found the upper spray arm in the bottom of the dishwasher after running it. I can't see any piece broken off of it but I also can't see any way to put it back on. I suspect some small piece broke off in a very clean break and I just can't see it. Is this fairly easy to purchase and reattach myself? I can see the holder for it screws in and out easily.


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Frigidaire FGHD2433K 24 in Builtin Dishwasher

I think I am finding small pieces of the wrap from the tablets in the small holes in the spray arms, one wont move anymore??? This is about 10 yr old maytag machine. I tried to clean out the spray arms but dont really know what I am doing. Bought a new diswasher, dont want to use the tablets if they will clog up the works. please advise.


Just prime the sink before you start the dish washer ... Maytag Jetclean II MDB8551A Dishwasher

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We have a built in GE dishwasher. It has worked fine for about 4 years but now the glasses in the top rack will not come clean. I have cleaned all the holes where the water comes out but I think the sprayer that is beneath the top rack (the one that is attached to the bottom of the top rack) is not rotating. We had someone out to take a look at it and they said it was fine. It isn't fine as it is not cleaning the dishes. Is there a reason that the bottom sprayer is not turning?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Maytag Dishwasher

Had my Maytag dishwasher for just over 2 years. Lately is has been making a loud grinding/vibrating noise - like something is stuck. I actually pulled out a piece of a plastic twist tie or something and thought I had solved the problem. Worked like a charm for a couple of days and suddenly the sound is back - and worse! I've read here that you should remove the bottom piece and make sure nothing is stuck before calling service. I'm the woman that's going to do this and could use some guidance ..


... Maytag 24 in. MDB4651A Built-in Dishwasher

Our son has a Bosch DW Model SHX43CO5UC/46. Purchased in April 2008. Machine worked fine. Was removed for a kitchen remodel-then reinstalled. It won't work now...just hums when turned on. He did place a quart of water in the bottom - it was pumped out. He then turned it on and it started to cycle - then back to the hum. One tech came out and could find no problem. A


... Bosch 23 in. SHU 8805 Built-in Dishwasher

Not cleaning dishes especiialy the ones on top rack. Found some broken glass pieces in bottom. No obstructions in line leading up to top washer. It looks like the pump is not pumping enough water pressure and/or volume for the top washer to function properly. Please help. Whirlpool Quiet Parnter I. Approx. 2-3years old.


If you remove the filter in the sump area underneath the lower dish rack (removing the screws to do so) you may find debris blocking/jaming the impeller area. Be very careful of almist invisible broken glass. Inspect the impeller to make sure it is ... Dishwashers

Bosch she44c06uc. Like many here, changed out the garbage disposal and didn't drain. Have reset the system by holding the "Drain Cancel". No help. The cycle stops at draining. Investigated and found small piece of glass wedged in the impellor. While having the interior cover over the impellor off, the motor for the drain impellor is humming, but the impellor does not move while engaged. The impellor will rotate by hand and stops at a point at 3/4 turn. I am hoping it is not in need of a new moto


Check the center of the impeller, it should be flat on one side round on three, the impeller might be rounded out from the shaft it sits on. You might just need a new impeller. Good Luck, N let me know Thanks. jimmy ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Glasses int he top rack of my kitchenaid dishwasher don;t get clean. they finish the run spotted and covered in what looks like baked on dirty dishwater. dishes in the lower rack look ok, but the silverware is always dirty, too. i figure it's one of two things - either the top sprayer isn't working, or the machines doesn't drain the dirty water well enough. or maybe it's something else - cycle regulator? the machine is about 4 years old. thanks


If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is to add some vinegar to the bo ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Maytag dishwasher #MDBF. It has started leaving small pieces baked onto the glasses and dishes. I have checked the output tube and it seems to be clear and I find nothing in the bottom strainers. can you suggest anything for me to look at?


Hi If the dishes are still dirty after the dishwasher has completed running, first check that you have the right wash cycle selected. This is because you may have selected a short cycle to save water and energy, but it is inappropriate for the load. ... Maytag MDB9600A Jetclean II Built-in Dishwasher

ASKO d 3122.. Keeps filling up the overflow area on the bottom of dishwasher. WHich sets of the overflow switch, then i get the flashing tea cup again. I will empty the over flow area. It will reset, We get one good wash out of it then on the next load it will stop work ing again and get the flashing Tea cup again, Back to unplugging the unit and draining the overflow area again.


... Dishwashers

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

My dishwasher after the cycle is over still have a bit of dirty water remaining on the bottom. After few hours is getting more and more dirty water. I have a feeling that some kind of the valve is not working correctly which allows the water from the sink drain to come back? Am I right? Is it a big re[pair or marginal? My dishwasher is about 20 + years old and still the greates one I owned ( I had before Bosh ). I own the dishwaser for last 4 years but previous owner loved it and never repair


Hello Ma'am/Sir,\012 The Best thing you're going to do is to have new Dishwasher.A lot of brand new products can help you, rather than striving the old one...Hope it will help you! God Bless you...Thank you! ... Miele Dishwashers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

Hi My F&P dishdrawer flooded. Dried it all out etc, the top drawer doesn't complete the cycle and it beeps continually even when it's not running. I am wondering if I can reset the drawer using the front buttons to get it back to factory default. Bottom drawer works fine. There is no error code on the screen only the lock icon which won't go away. Any ideas?


Not sure if you tried turning the power off at the main switch. Lock icon can gone away if you press the necessary keys as shown in the user guide. Also the sequence of keys to press for getting factory defaults of different options is also in the us ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi I've inherited a Zanussi DA6142 Dishwasher from a recent house move. It was treated quite poorly by students who I suspect ran it without the filters in place. I've used a dishwasher cleaner and was able to pull out the lower spray arm and rinse out all the crud that was blocking it (small stones, food, plastic, pieces of glass, paper, etc) but I cannot for the life of me work out how to get the upper spray arm out. The PDF manual I've downloaded for this model says DO NOT remove upper spra


... Zanussi Dishwashers

John Lewis dishwasher jldww1203 error code 30 tipping rocking works very temporarily as in just a few mins maybe 1 cycle, had side off there a pipe that just hangs fromtge bottom of side water thing it drips small amount less than teaspoon in entire cycle


... Dishwashers

I have a kenmore elite dishwasher model # 665.13103k902. It was working just fine & then one day I ran the cyle and it lost all power in the middle of the cycle leaving water standing in the bottom. My husband checked the breaker and also unplugged it and plugged it back in and still nothing...any suggestions?


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.3695 seconds