Having problems with your LG Dishwashers ?

Dishwasher stops working., all indicator lights go on and display shows OE


Answers :

Hi
\015\012\015\012


\015\012\015\012

OE in your LG dishwasher is a drain error and dishwasher not draining issue usually occurs due to\015\012kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for\015\012any visible clogging, remove if present. If no visible lint is present then\015\012remove then turn off the dishwasher and remove the drain hose and check for any\015\012visible clogging. If it's still not visible then the drain filter or drain pump\015\012is clogged and you'll need to clean the drain filter and drain pump. Also,\015\012check for any food pieces stuck near the pump impeller. Hope this helps... Please post back for any further\015\012assistance.
\015\012\015\012


\015\012\015\012

Daniel
\015\012\015\012

Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher stops working., all indicator lights go on and display shows OE


Hi\015\012\015\012 \015\012\015\012OE in your LG dishwasher is a drain error and dishwasher not draining issue usually occurs due to\015\012kinked drain pipe, clogged drain filter or drain pump. Check the drain hose f ... LG Dishwashers

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

We have a Maytag MDW700EDWG washing machine and it has stopped working. The display window is showing F2 and will not go to the time lenght of any program. I am unable to switch it off at the Start button. It is making a noise as if it is trying to do something - but then stops. I have cleaned the filters, checked water supply but still have F2 showing. Please can you shead any light or let me knoiw what to do Many thanks Emma


Is it the salt reservoir that is empty?\015\012Did you solve it already...mine has the exact same issue now ... Maytag Dishwashers

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

My mdb7100awq has stopped working. it does fill but they stops when the float assembley indicates either enough or to much water. Pressing the drain /off -the same as wash indicates lights and shows numbers andt there is some clicking but no washing.


... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

Dishwasher does not seem to have power. I have a Kitchen Aid, under counter unit, 9 years old, model KUDS01I. I used it 2 nights ago with no problem. When I push a button, nothing happens, no lights show, etc. It is plugged into the lower half of a duplex socket with disposal plugged into the top. Disposal works, so the problem seems to be with the dishwasher. That also eliminates any issues related to breakers or ground fault indicators, etc. Is there a reset button on the dishwasher? Is there


... KitchenAid Dishwashers

I have a diplomat ADP 8342 slimline dishwasher which has just stopped working,the green on light comes on but the programme buttons won't,however if you turn the green light off and then press the programme button they beep and the red light shows briefly.


... Hotpoint Dishwashers

I have a Fisher and Paykel DW60CDX1 dishwasher, the display originally came up eith an error code for the door, which seemed to be the problem as it restarted with some pressure on the door, then it stopped again and now there is no LCD display and no action, cycle butten lights are on but will not make a noise when pressed. We live in the bush and cannot get a easy service option. Is there a diagnostics mode I can try, although the LCD may not work?


Old question, but for anyone else, hears the answer - http://www.recalls.gov.au/content/index.phtml/itemId/1015047This model has a product recall, minehas done the same as described above, recall issued Aug 2012. ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Electrolux ESL63010 integrated dishwasher 10 months old- works for a few seconds, then stops and beeps continously. & the End indicator light flashes once. I turn it off, cancel programme, set it again, shut the door -it starts and goes on to complete the programme and washes the dishes perfectly. It has been doing this 'performance' for a week now -every time I use it- can you shed any light please


... Electrolux Dishwashers

We have a Haier DW12-PFE2-U dishwasher thats 2 years old. The cycle stopped yesterday leaving an amount of water in the bottom and all of the program lights are illuminated with a recurring beeping sound happening. It says in the booklet that the drain hose is too high or bended. But its not. The display does show the time when a cycle is selcted but nothing happens. The dishwasher turns on and off normally. Can this problem be rectified? thanks!


Refer userr guide on page 21. It reads...\015\012\015\012When all the programme indicators " J" blink.\015\012Have you checked whether:\015\012the door is closed properly.\015\012\015\012 ... Dishwashers

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. Thanks


... Whirlpool 24 in. GU3600XTRY Stainless Steel Built-in Dishwasher

Do indesit dishwashers have a reset button? If so where is it located on the dishwasher? As ours just stopped working for no apparent reason yet the power light still shows up but when you push any of the 4 cycle buttons nothing happens?


No they dont have a reset button you might be able to reset by holding the on button for 4 to 5 seconds ... Indesit 24 in. D63 Free-standing Dishwasher

Two days ago my LG dishwasher model lDF 7810BB worked fine. Yesterday I loaded it and the display panel will not light nor show any sign of power. I check the circuit breaker several times and all other electrical items work fine in the kitchen. The 2 year warranty expired 9/08/08


Check for voltage with a multimeter at the wires very near the front, just behind the kick plate. Follow the incoming electrical wire in and remove the little plate the covers the wires/wire nuts. I have seen wires that appear to be connected prope ... LG 24 in. LDF7810 Built-in Dishwasher

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

My Fisher Paykel dw60cdw2 dishwasher stopped working mid cycle and I cant get it started again even aftre switching power off and pressing reset.. All lights on the console are working except the number display on the left side. What is the problem likely to be


Had the same problem and it was the microswitch that is behind the door skin which is associated with the lock mechanism. got a new one and away she went ... Fisher and Paykel Dishwashers

By jleejr on Jul 20, 2010" " I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breake


HI. The actual culprit in this situation will be your control panel(Defective Touch-pad circuit board). The panel and touch pad assembly are integrated. They share the same space. There is a small ribbon cable on the rear of the control panel that li ... Maytag Dishwashers

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

My ASKO 1805 Dishwasher started to smell weird and white smoke came from it. I turned it off, but after I turned it on again it just keeps pumping water in and out, I can't get in contact with it (None of the indicator lights are working and it is not reacting to any commands) In addition the safety feauture that is supposed to stop all operation the moment the door is opened is no longer working. (i.e. even with the door open it is still pumping water) Does it sound like an expensive repair? (


Hello,\015\012\015\012Welcome to FixYa. Based on your description ( specifically the white smoke and smell ) I would suspect the control board is faulty. \015\012\015\012If the unit does not stop when the door is open can be r ... Asko 24 in. 1805 Built-in Dishwasher

Our Westinghouse dishwasher stopped working at the start of a heavy wash cycle. The light inside is working but the control panel is not. There is no indication of any power on the control panel.Your assistance will be welcomed


If there is no power to the control panel it must be a failure of the power supply in the unit.\015\012First of all ensure that the mains supply comes into the control panel from the power plug to the unit. \015\012The program controller ... Westinghouse Dishwashers

Fisher & Paykel dishwasher beeping with red light indicator. Won't stop unless unplugged. Doesn't work, (won't drain when it did work), can't change cycle. Have not used it in a long time due to problems


Try pulling out the bottom drawer and check to see if there is a puddle of water around the circuit board, if so it will make it do a lot of wierd things. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1800 seconds