Having problems with your LG Dishwashers ?

LD 2140 WH

\015 Error E1\015

Answers :

Repair Help & Product Troubleshooting for LG Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

Machine doesnt start . when on button is pushed and regular wash button is pushed it goes to agent and cycle is at 0 flashing (both 0 and agent lites).have tried to shut it off and main switch and turned it on and off a few times. and still the same


Because the timer controls many operations, a faulty timer can cause many problems. The timer is a complex component, so you shouldn't attempt a do-it-yourself repair. Test the timer with a VOM set to the RX1 scale. To gain access to the timer, ... Bosch Dishwashers

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

This dishwasher caught fire it got to hot and burnt the plactie around the bottom by the element. This modle has been recalled what can I do? GSD2620J01SS AG736720B not sure if the 0 are zero's or the number 0


... GE Tritonr XL GSD6260JCC Dishwasher

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

Nothing comes on on my kitchenIaid KUDI24SEBL4.checked door switch(2poles,com and NO3)res was infinite across com and NO3 and 0 when the actuator was depessed.the actuator has to be held down after it clicks to get a 0 resistance otherwise it goes to infinite.is this correct.if so I guess I need to check the timer?


... KitchenAid Dishwashers

Bosch DW SHU66C02UC/23 control unit 447325 keeps stopping and going back to 0 during wash cycle. Why


... Bosch Dishwasher Control Unit - 447325

How long should a normal wash cycle take for a kitchenaid dishwasher type 577 0


... KitchenAid Dishwashers

Replaced control board 447325 in bosch SHU66C05UC/23; FD860300407. What code to select 0,1,2,3,4?


... Dishwashers

Zanussi dishwasher when cycle finished displays .60 instead of 0?


... Dishwashers

Bosch SHU43 Dishwasher runs full cycle to 0 but circulation pump never shuts off.


... Bosch 24 in. SHU43 Built-in Dishwasher

The wash cycle times seem to vary considerably , but the trouble is it runs even after the timer reaches 0 and when I stop it the dishes aren't very clean . It does this @ every setting


Hi,There could be many Reasons. Few main Reasons are as follows :-\015\012\015\012 \015\012 Water-inlet valve\015\012 \015\012 \015\012 \015\012 \015\012 ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

Doesn't appear to be washing the dishes like the spray arms are not working. I can hear water filling and it does drain but soap is still on the door and in the bottom of dishwasher itself. Ran diag on it and it came back clear (0). I have a Bosch SHU5315U6.


Sounds as if the pump motor has gone out in the machine. What happens is once the water reaches a certain level the machine goes into clean mode. This means the pump the forces the water into the machine isn't working. The timer actuates this pump ... Dishwashers

We have Bosch model SHE44C02Uc. The motor seems to run for more than 10 hours, even though the indicator is on "0" minutes. Our dishes are cloudy, there is food always on the bottom, the filters have been cleaned -as much as we can get them clean of calcified dishwashing detergent.


Can you tell me how you can allow this to run for 10 hours ????? Are your sure you mean ten (10) hours?\015\012What in the world are you thinking while this is going almost half the day ? And then you say everything is still dirty.... somethi ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

I have an Arthur Martin ASF 2655 and the timer continues to turn from 0 to 1 to 2...... how do i reinitialise it


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

The count down timer gets to 1 stays there a long time, then resets to 23 or so, gets to 0 in about 3 hours or so. What do I need to replace? Thanks for your help.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description I'd say the issue is with the control. Bosch has had a history of this exact problem I'm about to lay out for you and this is the fi ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher cycles through all programs but will not drain or turn off at the end of cycle. I do not know if it drains inbetween. It just continues to run on 0 minutes and when I turn it off and open there is standing water


Underneath the machine there is a donute shaped styrofoam item called a flood safty switch .makke sure there is no debri underneath..mice will drag animal food or chew on this and will lodge it leaving debri under it causing it to trigger a false flo ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

Bosch Dishwasher SGS43E02 Exxcel. Switches on at main switch (0 appears in the numerical display) but none of the right hand programme buttons seem to be working! Have checked filter on water supply hose and that doesn't look blocked.


Obviously a faulty connection. Lots of switching off and on and holding down the buttons eventually sorted it! ... Bosch 24 in. SGS43E02 Exxcel Built-In Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

Maytag MDB9100ADB My Maytag won't turn on. There is a faint "0" displayed on the digital panel, but not sure what went wrong. Any ideas?


Check and see if the controle panle is locked out, if not, may need to shut-off the breaker in the main breaker panle to see if the unit will re-set itself. ... Maytag MDB9100A Dishwasher

The original control unit from Bosch' dishwasher SHU4302UC/14 has been replaced after recall from Bosch with a new one that stop working after three washes. It does not respond to any command and shows ''0'' at display. What may be the problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

Echolink Satellite receiver (el- 3020 ir plus) this dish has been installed sometimes ago then been remove from the pole by my neighbours stating that i was using their pole since then it's been laying on the roof today i managed to get a pole and fix my dish to it in almost the same spot it once occupied. this is what i get on my screen while trying to find channels: satellite : Astra1C/1E/1F/1G TP Index : 76/76 Signal Intensity : 62 % signal Quality : 0%


Sir I have receiver el-3020 it plus I wana to open all code would u like to help me and also tell me how to do upgrade this receiver pla ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0131 seconds