Having problems with your LG LDF6810ST Stainless Steel Built-in Dishwasher ?

LE on display

\015 LE appears on display and dishwasher cycle stops. Any idea what 'LE" means?\015

Answers :

I just had my LG dishwasher fixed. I told the repair man that LE light was comming on. Even over the phone the repairman said its probably broken wires on the door. Me being in construction for years looked around the door for wires. Anyway the repairman took off 6 screws around the door, took the cover off. You will see about 50 wires taped together. He pulled them aside and visually checked them one by one. Sure enough two were broken in two. He twisted them together put tape and he was gone. $87.50 Still Working!
LE Is a motor error.

( Motor error ) Condition : The motor is working abnormally. Possible \015\012cause : Wiring connections. The impeller of washing pump is locked. The \015\012rotor of washing motor is locked. The blade is locked.

Solution:

Correct wiring connections. Replace the cause of restriction. Replace \015\012the washing motor. Replace the power control board.



Repair Help & Product Troubleshooting for LG LDF6810ST Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

My Electrolux Dishles DX 303 Diswasher is displaying .50 on the led display after stacking and going to start it. It will work for a short time and then this code will display. What does it mean and


... Dishwashers

I have a Miele G 2470 scvi dishwasher. Machine displays F24 in display, lights flash, machine beeps and it won't run. Miele manuals seem to have no reference at all to error message displays. any thoughts?


... Miele Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

I have a newer model GE dishwasher. About a couple of weeks ago we lost power to home. When power was returned the dishwasher was making a high pitch sound and power was not returned to the front display. I had to remove a black/white wire from front of the display to make the high pitch sound go away. Do you have any solutions to make the high pitch so go away and for power to be restored to the front display? Thank you.


Hello\015\012\015\012High pitch sound comes when the main control also known as the electronic board goes bad and needs replacement. Please try to blow air with hair dryer on the display just to check if that'll solve the problem. Hope yo ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

The display started to flash and fail but intermittently displayed and did a cycle so I know that the mecanics are ok but display is now not lighting up have done the usual checking of fuse in plug etc


... Kuppersbusch K 24 in. IGVS 669.1 Built-in Dishwasher

I have a Bosch dishwasher Model SHE58C05. This model has two displays, one on the front where you can see and one with the hidden controls that you can't see when the dishwasher is closed. The display in the front all of a sudden stopped working today. Top still works but I can't tell how many minutes are left while its during the cylcle. I did have to cancel a cycle this morning because I picked the wrong one. Is it possible I hit a strange sequence and somehow cancelled this display (wishf


If you check your user manual there is a section that will guide you through turning off/on the display screen. I have tried to include the link for Bosch manual downloader but their site is down at the moment. If you do not have your manual and ther ... Dishwashers

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

Jenn-Air Expressions' Built-in Range. Two ovens top & bottom. Display unit on front fades out to blank. Display Unit called "Single Oven Display" NP-3; Date Code is 23-96 Robertshaw Jenn-Air BRK


... Jenn-Air JDB1105AWW Built-in Dishwasher

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

The led digital display on our Neff dishwasher is faulty. When the machine is started the display on the front is blank ( top of door display is still working). This is a S4409 modle, integrated stainless steel bought in 2006


... Neff Dishwashers

BF72 won't empty,display light out blank display ,no error code


... Hotpoint 24 in. BF72 Built-in Dishwasher

Have a Siemens dishwasher SD561591GB/23 only 2yrs old which displays flashing water & rinse aid lights.The rest of the display is off and machine does not work.I've topped up the rinse aid and


... Zanussi 24 in. DA6141 Built-in Dishwasher

We have an LG dishwasher model LD-12AW2 that randomly goes into alarm tone & displays "PE" on the display. what is the problem??


... Dishwashers

Display not showing any display.


1) Test any fuse blown or c breaker inside,retight very well any wires connectors!2) IF remain the same problem.the board is faulty.3) Replace the board call to the factory if you can get some rebate from old board vs new board.God bl ... Bosch 24 in. SHX99A15UC Stainless Steel Dishwasher

It is displaying 1hr on the digital display.


Good morning. Thank you for your support. I did in fact solve the mysterious problem. The dishwasher has a delayed 1-3 hr timer on it. Apparently some fingers decided to play with the key pad and it had to be re-scheduled.\015\012Thank you ... GE Dishwashers

My Miele G1320scu is displaying F14 in the display during washing cycle and stops. Anyone?


... Miele Dishwashers

Dishwasher display dims and then displays PF


... Frigidaire GLDB958JS Dishwasher

Wrench display in the display i have a pic of a wrench what the problem?


This is a service needed indicator. It is usually shown in conjunction with another error code. Check the manual at the following link for further interpretation: ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Electronic control pad is pushed for quick wash and the LED display would show 52 minutes. Now when it pushed the display shows 17 minutes and performs all the functions that would occur at the end of a normal cycle. Can set for the longer wash cycle 94 minutes and performs all functions start to finish. Think the control board is bad any advise.


... Maytag 24 in. DWU9902 Built-in Dishwasher

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

I have an SHU 4322. It displays "2H" in the countdown window. It will drain-cancel properly, but all of the programs display "2H" instead of the normal # of minutes for each cycle. How do I get the wash cycle to start normally?


Just reset the unit by unplugging the cord from the wall for 4 hours. The purposed for this is to drained the current stored in memory IC . So it will works normal again. Plug it again after 4 hours to see the result..Good luck: ... Bosch 24 in. SHU43 Built-in Dishwasher

Whirlpool ADP5966 developed a leak at small rubber connection from circulation pump. Leak repaired, machine reconnected, programme selected, some sound for about 20 secs then shutdown. Display showed F6 once then nothing. L.E.D.programme indicator glows, display remains blank, start light flashing. Help please


... Whirlpool Dishwashers

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0204 seconds