Having problems with your LG LDF6810ST Stainless Steel Built-in Dishwasher ?

HAVE HAD DOOR LANYARDS REPLACED (YESTERDAY). BEFORE THIS THE DOOR FELL OPEN TO THE FLOOR SEVERAL TIMES BUT MACHINE STILL WASHED OK. WON'T WASH NOW. WHEN "WASH" BUTTON IS PUSHED IT GIVES OFF A DOUBLE CHIME & DOES NOT START A CYCLE. MURRAY


Answers :

Repair Help & Product Troubleshooting for LG LDF6810ST Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HAVE HAD DOOR LANYARDS REPLACED (YESTERDAY). BEFORE THIS THE DOOR FELL OPEN TO THE FLOOR SEVERAL TIMES BUT MACHINE STILL WASHED OK. WON'T WASH NOW. WHEN "WASH" BUTTON IS PUSHED IT GIVES OFF A DOUBLE CHIME & DOES NOT START A CYCLE. MURRAY


... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

I have an LG dishwasher Model LD-O5AW2 Benchtop. IT has been going perfectly until now. I push the button in and then the start button, when the wash cycle has finnished it wont empty until I push the stop button off and then on again. Then it empties and goes to rinse but wont come out of the rinse cycle, just keeps rinsing, until I turn it off and on again.Up until now its been a great little dishwasher. JOAN


... LG Dishwashers

I have a Bosch SHX43M05UC Dishwasher. To wash, you select the cycle and then close the door to start the wash. Now when I push the on button, the pump turns on. I can't tell if it's pumping water or not but it's not supposed to start until the door is closed.


... Bosch SHX43M05UC Built-in Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

I have a fridgidaire dishwasher model # FDB 1450chc2 andon the control panel the red lights are flashing and washer wont start ?? when I open the door the lights go out but when I close the door and push start the washing lights start to blink but doesnt start to work ?? Need help thanks [email protected] Brian


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


... Maytag Dishwashers

My dishwasher 'start" button won't kick in. The machine seems to think it isn't locked - light wont activate, but the door IS locked. I select the cycle and option, but when i push start, it won't stay, The "clean" button keeps flashing. This is 5 years old


Hi,How many Blinks are there?Is it 7 Clean Light Blinks?Let me know, so that we could proceed.Hope i helped you.Thanks for using ' Fixya ' and have a nice day!! ... Kenmore 24 in. 17032 Built-in Dishwasher

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

Wont start When I push the start button, the washing light starts to flash, but the dishwashing cycle won't start.


The lights flash when the door is not shut all the way, or the sensor that detects that the door is shut is not sensing the door is shut. Try pushing in on the door while hitting the start button. ... Frigidaire 24 in. FDB1051RE Built-in Dishwasher

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Why does drain motor start when pushing the start button on the door before the door is closed?


It's almost certainly the float switch in the bottom of the machine. In the bottom is a polystyrene 'float' that is either active due to water in the bottom or is faulty. Tip your machine to the side and remove water and try again, bridge or replace ... Bosch Dishwashers

Whilpool gu2300xt,wash cycle lights wont light,when i push start button goeswt calcell and drain and you can here drain pump then it shuts off


It is likely there is some fault with the float switch. Which means the dishwasher thinks it is overfilled with water and tries to empty out to protect itself. This is why the pump turns on as soon as you try to run the dishwasher. Refer ... Whirlpool Gold 24" Tall Tub Built-In Dishwasher - White-on-White

KitchenAid kudpo1flss dishwashe wont do anything. If you push the buttons to start wash nothing lights up and it will not start. thanks for any help you can provide.


If the unit won't start and there are no signs of power make sure you're\015\012 dishwasher is getting power. If so then likely you will need a new \015\012fuse which if you go to the link below, you can download a video to show\015\012 you how to r ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Last month i was washing dishes in the dishwasher and if i remember correctly i opened the door to get a knife out of the dry cycle. i remembered shuting the door back and that is about it. this is my daughters dishwasher by the way. i left her house not noticing that the dishwasher ever finished. a week later she asked me if i had a problem with it. i told her no. when she goes to push the start button nothing happens. it doesn't restart its self. we have turned the breaker off and on


Hi.Depending on the model you may need to reset the dishwasher. Most Kenmore and Whirlpool built dishwashers for example need to press a reset button sequence to operate again after a problem has occurred. In that case you usually get lig ... Dishwashers

Neff dishwasher our dishwasher is six years old and have had no problems till now . there is power to it but when you push the on button the impeller starts up even when the door is open , and it wont go through the cycle , its asif there is no water going in and it is not draining away i have checked and cleaned the filters but nothing, then pulled it out from undre the sink and it started working . i put it back , it went through the cycle then the next day it would'nt work again . do i need a


You have a faulty door switch. It can be replaced and may be available at youre local appliance parts dealer. ... Dishwashers

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

I have a whirlpool DU943PWKQU, first about 6 months ago all the push buttons except light wash stopped working. Now this week it started giving me problems starting all together at first I resolved by unplugging and replugging the electrical cord but this is no longer working. Can you tell if something can be done?


It seems to be the program controller and you will have to get this checked. Remove the power off for some time and reset it back . If the programs are not responding then you will need to check from the power cord to the control panel to see if this ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1957 seconds