Having problems with your LG LDF9810ST Built-in Dishwasher ?

I have an LG Dishwasher model LDF9810ST. Error code E1 keeps showing (Water Leakage Problem) NO water problems anywhere to be found. I have a hard time shutting down the machine. It has had a new MAIN BOARD, and a NEW MOTOR. This unit is not 1 year old yet. Any suggestions?


Answers :

Are you draining the unit in the basement or under the kitchen sink?
\015\012
\015\012If you are draining the unit to the floor you will need a new drain hose with a syphon breaker. This drain hose is factory installed on all new LG dishwashers.
\015\012
\015\012The part # is AEM69493801
\015\012This is a known issue and may be covered under your factory warranty.
\015\012
\015\012Depending on where you live a factory service tech may be in your area.
\015\012
\015\012Could you explain the second problem further...Hard time shutting down?
\015\012
\015\012Shoot me a E-mail @ [email protected].
\015\012I am a LG factory service technician not a sub contractor.
\015\012
\015\012Mike
\015\012
Repair Help & Product Troubleshooting for LG LDF9810ST Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an LG Dishwasher model LDF9810ST. Error code E1 keeps showing (Water Leakage Problem) NO water problems anywhere to be found. I have a hard time shutting down the machine. It has had a new MAIN BOARD, and a NEW MOTOR. This unit is not 1 year old yet. Any suggestions?


Are you draining the unit in the basement or under the kitchen sink?\015\012\015\012If you are draining the unit to the floor you will need a new drain hose with a syphon breaker. This drain hose is factory installed on all new LG dishwas ... LG LDF9810ST Built-in Dishwasher

Asko 1875 had a new main board, wax motor and temp thermistor fitted 6 months ago. now thw machine pumps in the water but does not wash what could be the problem


Hello, welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1875 and 2) filling with water, draining, heat ... Asko D1876 Dishwasher

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

The dishes have food residue washed onto them and water spots on all glasses regardless of the amount of detergentinse agent. The pump seems fine there is no water left in the machine after a cycle. any suggestions other than getting a new machine? thank you!


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch shu43c02uc Hi, My shu43c02uc/40 bosch dishwasher does not drain water. The pump works well when I start it from the overflow mecanism. I mean, the pump evacuates water nicely. The dishwasher does not perform the draining activity for all the programs. The main control board is new. Is there any idea? Thanks.


Test this steps and fix it. God bless you\012 \012 Belt, Water Pump\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

I have a hobart LX18C. I purchased a new control board and as I found out its factory set to the h model. How do I change the board over to the c model. How do I program the machine for the different wash cycle times, I have one that is working but its on the 140s. cycle and only heats the water to 80 degrees. I see the push buttons on the control and wonder what they are for.


Here is a Hobart link that may help. https://feg.hobartcorp.com/resourcecenter/ProductDocumentation/F18615%20Rev%20I.PDF ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hi there,i have a brand new but 3 year old,diplomat 8332,just fitted it,it does the pre was ok,pumps out the water,goes to next stage,you can hear water entering the machine,shortly after it has started the main wash,it starts to cut out intermittantly,then F2 code appears,and a bleep.i have taken the lower panel off and checked for leaks and to see if the valve was free,all ok,also relay click in front panel,safety cut out ? any ideas please.


... Dishwashers

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

Maytag dishwasher MDB7709AWS2 - control board failed - fitted new - when power switched on unit drains even with no water in machine then after 30 seconds wash light comes on then after another 30 sec


... Maytag MDB7709AWS Stainless Steel Builtin Dishwasher

My Diplomat HJA 8630 dishwasher has stopped working. Put cycle on machine filled with water then no power and can not drain dishwasher. Fuse checked and changed, so not mains power supply. Any suggestions??


... Dishwashers

Power washer - model jcb-pw20tss. TSS=total stop system. seems to be ''stuck'' on my model. Can you suggest method to free up and restore pressure which will allow me to switch on machine again. Mains electric =OK Fuse = OK Connected to water supply =OK


... Pressure Washers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem


The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher

The circuit board on our Miele G646 dishwasher has failed. do we 1) see if we can get another one second hand and in which case what other models have a compatible circuit board 2) try and get the board repaired and who do you recommend 3) bite the bullet and pay an exorbitant amount for a new board or 4) give up and just buy a new machine Thanks


What is the dwasher doing or not doing and how do you know it's the board. More information required please. ... Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

I have a whirlpool DWH B10W. Last week the main drain outside blocked and none of my service machines were working (not draining). The main drain has now been unblocked and every machine except the dishwasher are now working fine. The plumber has checked the drainpipes again and says all are now clear. When I try to use the dishwasher, after the initial drain it stops and starts beeping at me. I have also noticed that no water is going into the machine. What's happening?


The error most likely indicates a Long Drain Sequence (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. \015\012 \015\012 \015 ... Dishwashers

I have abrand new Black and Decker 1900 psi pressure washer. When I hook the water hose up to the machine and turn on the water, water sprays out out of the bottom without the machine being turned on. Thank you


... Pressure Washers

I bought a new kelvinator diswasher kd12mm1 - will not start, and shows E1 error. No water? but the connections are all done properly and the water is open. My previous machine had no problem with water pressure. I do not have salt yet... can that be the cause for the machine not starting? Please help


... Kelvinator Dishwashers

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!


Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1527 seconds