Having problems with your LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher ?

Tub wont fill with water

\015 Brand new dishwasher. Tub will not fill with water. No error codes on the display.\015

Answers :

Could it be the water is not getting to the machine? Usually there is a water inlet fitting on the back or bottom of the machine. Please check that first.
Be blessed.
Repair Help & Product Troubleshooting for LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

Tub wont fill with water


Could it be the water is not getting to the machine? Usually there is a water inlet fitting on the back or bottom of the machine. Please check that first. Be blessed. ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Wont fill with water, replaced the inlet water valve,still wont fill


First of all make sure the water shut off is on. Second check the water float is it jam on the top position that will shut off the water. then the timer switch that control the water inlet valve.Hope this 'll help. God Bless. have a nice day. ... Kenmore Dishwashers

The salt warning light came on (red) and went to put salt in but noticed it was filled with water. I have filled it with salt now and the warning light has gone off but now when I try to select a program it wont. I have drained the water in the salt dispenser but it still wont work! Help!


What is the make and model of the item? ... Dishwashers

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

I have a GE GSD3200 dishwasher about 6 years old, which had been working well until this past week. When turned to 'start' the motor runs but no water fills the tub. I then poured 4-5 pots of hot water into the tub and tried to re-start. As soon as it was turned to 'start', I could hear all of the water draining out. How bad does this sound :) ?


Look inside the dishwasher and there is a little round cup shaped thing in the bottom of the washer. It shuts the unit off if the water gets to high. Lightly push down on it to reset. It should fill with water now. You should look into why it was tri ... Dishwashers

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

HI there dish washer wont fill Ichecked fill valve its ok but there is no 110 volt reading to wires but when i remove purple wire from water valve and put ground wire to fill valve water comes in the dishwasher please tell what needs to be replaced thanks


There may be problem with your door switch/lock mechanism,be sure to check the main power supply to the dishwasher.\015\012if you have a electronic control board it might also have to be replaced. ... Dishwashers

I own a GE Profile GSD 4330 dishwasher. Recently it has been leaving some water in the bottom of the tub. This water accumulates over time until the entire bottom is filled. I have checked the air vent, garbage disposal unit and the filter in the bottom of the dishwasher (which was filthy). I cleaned the filter and everything else looks okay, but it is still leaving some water in the tub.


... Dishwashers

Dishwasher fills tub continuously until float turns it off whether in cyle, during drying or after cyle complete. That means during drying when the dishwasher is trying to dry the dishes the tub fills up preventing drying. This is a new dishwasher that I've never used. I allways noticed the tub was full of water, but thought that was just to keep the seals moist so they don't rot. I've been in my house 5 years and only hand washed my dishes because it was more convienient. Now that there ar


Ayacht, the fill is a timed fill controlled by the control board (part number 99003158). The float is a safety device designed to cut power to the valve in the event of a failure. The fact that the float is doing it's job and stopping the fill tend ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

Frigidaire fdb1500lsfo built in dishwasher. Have had for maybe 3 years. I push the start button, and it starts like usual, filling the tub with water. After filling, it will not do anything for about 5 mins, where then it drains. It seems to go through the whole wash cycle, but after it has pumped the water out. Dishwasher steams all of the dishes, but there is no water in it to wash them with.


... Frigidaire FDB1502RG Built-in Dishwasher

Good Morning, Tub fills with water but while washing the water drains out leaving the tub empty and no water to circulate.


... KitchenAid KUDA03CT Built-in Dishwasher

GE Profile dishwasher GSD4920Z02BB. When wash cycle starts, water starts filling tub, then drain opens and starts draining, as water continues filling. Water level doesn't get high enough to allow


... Dishwashers

Water wont drain out of bottom of tub. The dishwasher works fine, it just wont drain the dirty water out. If I restart it to wash again, the dishes are washed in the dirty water.


Hi, A clog in the drain line or air gap (if there is one) is the usual reason that a dishwasher won't drain. Often the problem is at the point where the drain line attaches to the garbage disposer or househ ... GE Nautilus 24" Built-in Dishwasher

Dishwasher tub slowly fills with water after after completion


The internal parts of the valve are sticking open randomley.the diaphram/piston in the valve most likley have lime deposits on it due to poor water quality.you would need the water valve assembly but before you buy this part i would look where the wa ... Dishwashers

I have the GLD 4560 NSS and it is no longer draining. The tub stays completely full. When you start it, the water in the tub is reused then it does not drain. No noise or anything when the draining or filling should actually be taking place. Hoses are not kinked, no leaks, no air vent, it drains directly to the disposal. Everything seems OK but it is full of water. Any help would be greatly appreciated.


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

Whit film on everything at the end of wash. dishes not clean I took off the screen and cleand a bunch of stuff out of the sump. seems the same. it is filling with water draining soap is all gone filled the rinse agent electronics seem to be working. inside of the ss tub is always crummy.. everybody else i know with a ss tub loves it.. im ready to put my old plastic maytag back in


\012Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

Wont run I have a Kenmore QuietGaurd2 it will not run at all. It filled up with hot water, then it quit working. It wont even drain the water out or cycle. Nothing is happening, whats wrong with my dishwasher??


... Kenmore 24 in. 15992 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0865 seconds