Having problems with your Magic Chef Dishwashers ?
Water not entering dishwasher. Worked fine one
\015 Magic Chef dishwasher DU55CA 01\015\01222 608411 R\015\012\015\012water not entering dishwasher. Worked fine one day, next day, water wouldn't come in.\015
The water-inlet valve lets water enter the machine. First Check to see if the valve is getting water. Make sure it’s not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you get power to valve when unit is put into operation may take a couple minutes to start a fill. If you have power and it’s not clogged up replace the valve .If you have no power to the water inlet valve check float switch. This can be done by checking the continuity. There is a video of this at http://appliancehelponline.com/dishfloatwaterinletvideo.html this will walk you checking the water inlet valve and the float switch. It may be a different model but the testing procedure will be the same. You can also enter your model # for diagrams and illustrations for most models. All parts come with installation instructions.
Repair Help & Product Troubleshooting for Magic Chef Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Water not entering dishwasher. Worked fine one
The water-inlet valve lets water enter the machine. First Check to see if the valve is getting water. Make sure it’s not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if yo ... Magic Chef Dishwashers
Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.
Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher
Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.
... Briggs & Stratton Prosumer 20324 Gas Pressure Washer
Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f
... Fisher and Paykel DS602 Dishwasher
I have a 2 drawer system - the bottom one is working fine. The top one does not turn off the water, so water keeps flowing into the unit and ultimately creates an overflow and flood condition.
You have to gain access to the fill valve see if it is opening or closing properly. You can test that by starting up the unit without the water. It should open on its own and close on its own. If it is unclear if it does it then you may want to ch ... Dishwashers
Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.
You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers
We have a Model 587.1440*, 587.1441* Kenmore dishwasher. I had turned the water off to the whole house when we left for vacation and openned one faucet so the water pressure would be off the house while we were gone. Upon our return, I turned the water back on but the dishwasher gets no water. ?? What happened? It was working fine when we left, now no water. ?/
First, have you run it long enough to purge the air from the dishwasher line?\015\012\015\012Secondly, the solenoid valve for the water inlet may be stuck due to no pressure on it while you were gone. Tapping it with something light like ... Dishwashers
I have a kitchenaid Model KUDW03CTBL2 dishwasher. It is pumping water, but the top sprayer and the one under the top rack just have a little water coming out. Not enough to make them spin. We also noticed the water in the bottom when opened is not as much and it is cool not hot. The dishes on the top rack will not clean, and the bottom is not completely clean. We have checked water pressure and water tempurature through the house, All is operating fine. This dishwasher is only 1 year and 10month
... KitchenAid Dishwashers
Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've
My unit fills with water on the first cycle, then the remaining cycles no water enters the unit. It works fine if I fill it with a bucketof water. Any sugestions on problem? Thanks you very much
... Jenn-Air JDB9910 Dishwasher
Bosch Dishwasher SMU 7052 UC14 Does not fill with water, water to dishwasher fine, cycles sound like they advance one to the next, thinking it is a water valve.
... Bosch Dishwashers
Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are
Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher
The upper rotating sprayer (beneath the upper dish rack) is not getting water but the lower one is working fine. The water connection is mating properly and the sprayer rotates freely and is not obstructed. Is there a solenoid controlling water to the upper sprayer?
... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
We have a built in GE dishwasher. It has worked fine for about 4 years but now the glasses in the top rack will not come clean. I have cleaned all the holes where the water comes out but I think the sprayer that is beneath the top rack (the one that is attached to the bottom of the top rack) is not rotating. We had someone out to take a look at it and they said it was fine. It isn't fine as it is not cleaning the dishes. Is there a reason that the bottom sprayer is not turning?
Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Maytag Dishwasher
Only a small amount of water enters machine when you start normal cycle. I took off water supply line at inlet valve... screen is clean, water preasure is fine.
You might have a bad water inlet valve, when triggered the inlet valve opens up to allow water to enter the machine, it's usually located behind the lower kick plate in either the right or left hand corner, if it's defective it would need to be repla ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
Lately the soap remains in the dispenser, dried and caked in (I have to dig it out with a sharp object, as it becomes a solid piece). I have also tried gel soaps, but find them in the bottom of the dishwasher, partially intact. The mistery is this does not happen all the time, but most of the time! I've checked the water pressure and the water temperature: both seem to be fine. The dishwasher does run a full cycle. Is it time to buy a new one? Would you also be able to tell me what year this mod
... Frigidaire 24 in. GLD3450RD Built-in Dishwasher
Bosch Dishwasher SHU42 Stainless Steel Burning smell I had Bosch replace the faulty piece that was part of the recall (it was fine before) I bought two of these the other one is still totally fine NOW the tenant is saying that is smells like its burning.. so they turned it off at the breaker.. Its full of water... now they say its going moldy? UGH. What can be causing the burning smell and how do i fix it please? Thanks
Disconnect the drain hose from under the sink and use a wet dry shop vac to remove the standing water.Then check the main wirng coming to the machine and make sure they are connected properly.there is also an inline fuse located bottom ride side of t ... Bosch 24 in. SHU42L05UC Stainless Steel Built-in Dishwasher
No water When I start the dishwasher, the display shows 96 and starts to go down but there is never any water entering the machine and "HO" starts blinking. The dishwasher has been running fine up until today.
First swith the machine and the water supply off and then where the inlet hose is on the back of the machine remove the hose from the machine and look in the plastic part that the hose screws onto there should be a small sieve there this can be pulle ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher
Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you
Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers
One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu
... Whirlpool GU2200XTSS Built-in Dishwasher
Hygena dishwasher water will not enter machine when turned on , replaced solenoid only works in one position is there a water level switch/indicator/ thats would prevent the programmer from sending 240 volts to solenoid
There is a pressure stat but these are reliable. a common fault is the wiring loom broken where it goes round the corner at the bottom of the door. take outer door panel off and inspect the wiring loom for breakage ... Dishwashers
The dishes come out with white film on them. During the washing cycle water is not hot, it's only luke warm. I thought it was the heater but the drying cycle works well. Is it all connected to one heater? It is not because of hard water. It worked fine just last motnh. Please help! Thank you!!!
Are you having any issues with your water heater at all. Make sure to run the water at the kitchen sink on the hot side first ti ensure hot water is getting to your dishwasher. Also make sure that the jet dry dispenser has jet dry in it. Hope this h ... LG LDF8812 Stainless Steel Built-in Dishwasher
I have just bought a house with this dishwasher. The first couple weeks it was fine, now not all of the water will drain. Ive taken it all apart and cleaned it but after washing there is about 2cm of dirty water covering the bottom. It happens with both but usually only one at a time. I have read horrible things about the dish draw, what could the problem be? Help Please
The most common cause of problems on dishwashers installed by the builder are Installation issues. Usually, the drain hose is kinked and food particles accumulates on the hose until it clogs completely.If you are planning to fix it by yo ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
Got a hoover hed 6612/80 been working fine today all four lights flashing and beeping. manual says too much water inlet. one soltion on here says to check water inlet sensor. How do i do this. please help.
... Hoover Dishwashers
Broken dishwasher It started when my dishwasher flooded my kitchen. I drained it and turned it on, it was fine. then it happened again. I have drained it then when I went to turn it on again it just sounds like it is running with no water. If I put water into the bottom it will drain but it will not fill up. I bought this house 3 years ago I am unsure how old the dishwasher, do I need to get a new one?
I have a kenmore model 665 168 29000 the mounting bracket have broken from under the cabinet, so when you open the door and pull the racks out the machine moves forward, how can i fix this????? ... Bosch 23 in. SHU33A Built-In Dishwasher