Having problems with your Maytag 24 in. DWU7402 Built-in Dishwasher ?

I have a leak when the dishwasher is running.

\015 Maytag DWU740GABE\015\012Dishwasher is probably 5-10 years old. It was in the house when I bought it in 2007. Has worked fine until recently. Its used only once or twice a week. Recently noticed some leaking at the bottom right of the unit when running. Not sure where to start for a fix.\015

Answers :

This is commonly caused by a worn door seal. This is a simple repair that requires no tools and can easily be accomplished in a matter of minutes. Over time, these seals compress to the point where they no longer seal correctly, or food particles and grime get caught between the door and seal and leave small air gaps. The silverware tray (if located along the left or right side) can also cause damage to the door seal as utensils get caught on the seal surface as you roll the lower rack in and out of the tub. As water splashes up against the inner door facing it rolls out the bottom of the door, or down along the sides instead of staying in the tub. The only other items that can contribute to leaking are:

1. A dishwasher that is not level, which causes the door not to seal properly.

2. The inner door panel being warped causing the door facing not to be even for the gasket to seat properly.

3, Dish placement. If you place bowls, serving trays and large tumblers in the front row of the bottom rack on some dishwashers it can contribute to water being deflected over the front edge of the tub and out the bottom of the door (Believe it or not, I've seen it happen).

NOTE: Most dishwashers do not have a seal across the front lip of the tub. That's why it's important to have a good door seal and to load it properly.

If you've loaded the dishwasher properly and confirmed it is level (front to back and side to side), then here are your options:

1. Replace the inner door panel (part number 99003678) at a cost of about $115.

2. Replace the door seal (part number 902894) at a cost of about $40.

I think I would pursue the cheaper option, first. Its also the much simpler option. To replace the door seal, follow these steps:\015\012 \015\0121. Pull the old door seal from the groove around the wash tub facing. Take note of which surface area of the gasket is inserted in the groove and which surface is facing the door. It may not seal properly if you install the gasket the wrong way.\015\0122. Clean the area really well to ensure there are no food debris or soap deposits. Also clean the inner door area where the door meets the gasket. You need a clean surface for the best results.\015\0123. Locate the center mark of the new gasket. This will be a small paint spot or small groove on the gasket (this surface is the side of the gasket that will be inserted in the groove around the tub facing). If there is no center mark, fold the gasket in half and mark the location with some chalk, or hold with your fingers.\015\0124. Locate the top center part of the wash tub facing and align the center mark of the door gasket at that point. Begin pushing the gasket into the groove with your hands and work your way around and down along each side.\015\0125. Make sure the gasket is inserted all the way around the tub facing to the point where it meets the wash tub bottom. You can pull the gasket out and readjust as necessary.\015\012 \015\012This repair should take you about 30 minutes or less to complete. Its simple and requires no tools. The door will be tough the shut for a while until the gasket compresses and takes the door shape. Do not slam the door if it becomes difficult to shut. Simply close the door and the push firmly at the point just above the door latch until the latch clicks. Slamming the door can damage the control panel components, the door latch and/or the hinges.\015\012 \015\012If you have questions, or require additional assistance, please let me know. I hope this helps you.
Repair Help & Product Troubleshooting for Maytag 24 in. DWU7402 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

When the water cycle is running there is a white plug by the water inlet that is leaking. When the dishwasher is not in the water cycle it does not leak. When the dishwasher is stopped in the middle of the wash cycle and water in in the bottom of the pan it does not leak. It only leaks when the water is running.


Crack in water inlet valve or a pin hole in the hose going from the valve to side of tub spraying water where you see it. You have a holein someting. You need to trace it back to its sourse. When you say "water is running"im guessing thats when its f ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Water leak have the Ge triton dishwasher (Model # GSD5320D02BB, bought it n 2001) and currently have very small amount of water leaking out of the door during a run cycle. I did check levels when running and that seems to be fine......meaning the dishwasher is level and not an over-flow problem. My next thought is maybe it is a faulty door gasket. So my question is, where is the door gasket located and how do I replace it? (and where do I order this part from?). Looked for diagrams to follow and


They are in the bottom left and right of the door opening. GE likes to use L-shaped, molded and ribbed seals on most of their models - hopefully also on yours. Typically these can be removed by hand and easily replaced without taking anything apart. ... GE Tritonr XL GSD6260JCC Dishwasher

Leaky Dishwasher I recently moved into a new house that has a brand new Magic Chef dishwasher. We haven't even had a chance to use it, but last night discovered water leaking from the bottom onto the floor. When I opened the door, there was about 3-4 inches of water inside. I baled as much of the (slimey) water out as I could, and that stopped the leak. Now afraid to run the dishwasher for fear that it might leak even worse. E71195 Type 777-0


... Magic Chef 24 in. DC4000 Free-standing Dishwasher

Leaking dishwasher There is standing water in the dishwasher when it's not being used. Recently we had a garbage disposal installed and was wondering whether this may cause the water from the sink to settle in the dishwasher. Also, the water rises and leaks on the floor. We have to run a wash cycle to drain and dry out the dishwasher. What do you think the problem is?


It sound like while the assembly of the garbage disposal, you placed the end of the drain line pipe in a lower position than it was before.\015\012Good luck! ... Kenmore 15129 Built-in Dishwasher

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

Dishwasher I am getting a run around with getting my LG dishwasher fixed properly. We had a tech more than once come in and look at our dishwasher. It has not been fixed and never dried the dishes properly. It is now leaking and going to a "del" level when we attempt to wash the dishes. It is also leaking on our fairly new tiled floor and under our new kitchen cabinet. Your tech stated the dishwasher was not installed properly. The installation dept , Francine stated it is not their problem


Not sure what you mean by a "del" level, but as far a drying issues:\015\012\015\012LG chose to use a very energy efficient drying method which relies on the residual heat of the dishes to help dry them rather than many manufacturer ... LG LDF6810 Built-in Dishwasher

Leaking dishwasher My GE dishwasher leaks when running a load of dishes. The leak seems to be coming from about the middle of the tub about halfway back. I can't see exactly where it's coming from, but it appears to be dripping right behind the motor. Could it be a poor connection? I would appreciate any suggestions. Thanks, Bob Engle I do not seem to be able to find the model number


Probably a leak at the motor seal where it enters the tub. Best to remove the motor if you can and inspect the seal. ... Dishwashers

Dishwasher is leaking in the front left (if looking at the machine). It isn't a lot, but appears to have been leaking for a while as there is a whole in the floor. It runs great, just has the leaking problem. It's a GE profile Triton Quiet Water III GE 24 in. GSD5360FSS Built-in Dishwasher


\012Hi,\012\012Here\012is a tip that I wrote about dishwashers and them leaking.Leaking\012Dishwasher ... GE 24 in. GSD5360FSS Built-in Dishwasher

We had a problem with our garbage disposal and it resulted with water leaking from our dishwasher. The disposal is fixed, I removed the excess water from the dishwasher. I tried to run the dishwasher empty to clean it. It runs but then the E-2 alert shows on the control panel meaning high water level. I read in the book that I may have to have a service person do some sort of a reset. Is this correct?


Contacted the company and they e-mailed instructions to fix problem ... Asko 24 in. 1895 Built-in Dishwasher

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Hi,Check your heating element.. Dishwasher ... Kenmore 15899 Built-in Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. Also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Best off to call a certified repair company such as Sears. ... Kenmore 15899 Built-in Dishwasher

Smeg dishwasher my smeg dwf409 dishwasher pump keeps on running will not stop after washing cycle and there is water leaking from the bottom of it i can not see any leaks around the pump does the tray on the bottom always have water in it


My hotpoint dish washer aquarius is 4 years old leaves a sandy grit all over dishes water not spraying the top,done all the usual stuff run out of ideas ... Dishwashers

My DD603 was leaking (both top and bottom) and I went to this web site and the person recommended changing the Lid Actuators which stopped the leaking for about one month. Now each time I run the dishwasher I get about 1-2 quarts of water on the floor. After reading the number of dissatisfied customers should I just buy a new dishwasher or keep chasing the all the problems associated with the DD-603?


In my honest opinion I would just buy a new one. I would say the same thing to change the lid actuators agian. Iam sure it would stop like before and then return later. It may be more cost effective time wise to just replace the unit. Sorry bbest of ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Motor keeps running; dishwasher won't fill. Noticed some leaking out of the bottom. Even when dishwasher is off, the motor runs.


1)problem in the board(relay) ... Dishwashers

My Frigidaire dishwasher leaks when not running. No leaks when it runs; I watched underneath while it ran through a whole cycle. What is happening?


... Frigidaire FDB520RH Builtin Dishwasher

Leaking dishwasher Asko dishwasher (8 years old) leaked while running. Is it time for a new one?


\015\012\015\012Main tub seal\015\012\015\012\015\012Note… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the following instructions probably apply to yo ... Asko Dishwashers

Whirlpool DU1101 Hello, My Whirlpool DU1100 is only 1 year old. The dishes are dirtu and the soap doesn't disolve completely My husband is convinvced it is low water pressure, primarily from a leak in the sprinkler system in the park behind our house. I think it is just a clog of some kind preventing the water from getting into the dishwasher fill and/or spray arms. The maunual says you need 20 120 PS to run the dishwasher I doubt it is below 20 PS because of a leak in the park. Is there anyway


Well you should have water up to the heating element. if there is more than likly your chopper is the culprate. do you make sure that there isn't big food particles on your dishes because that is a lot of stress on that chopper and that is what help ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

I have just bought a Kenwood KID60S10 dishwasher. I have used it a couple of times with no problem. However I realised it has been leaking from the water pipe at the back so pulled the unit out to tighten and readjust the pipe. However when I tried to run a cycle it won't after this to check if it was still leaking it won't. When I choose a programme non of the lights light up (except the power on/off light). I had left the washer out of the cavity to ensure the pipe wasn't leaking anymore. It i


... Dishwashers

Hi, I have a Kleenmaid Dishwasher and the anti-flood system is being triggered (when I tilt the dishwasher, water runs out onto the floor). I am quite sure the leak is coming from the pump as the dishwasher stops during a drain cycle. How do I take of the panels to check what the problem is?


... Dishwashers

Whirlpool GU1100XLTQ1 dishwasher, 4 years old is leaking water during cycle. I cannot see exactly what is leaking by looking up through the acess panel in front...there are what appear to be plastic support ribs for the tub and water is leaking through several of them to the left of what appears to be the motor in the center...please help! I don't think I can run the washer and tilt it back at the same time as the water supply line only allows me to pull it out just enough to clear the counter t


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wahgfadh ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

I have a 12 year old Kenmore Ultrwash Model #665.15951790. I recently replenished the rinse aid dispenser and am experiencing an oversuding problem. It was oversuding to the point that suds were coming out the bottom of the door. Did notice that the blue rinse aid seemed to have leaked into the dishwasher due to a puddle of blue rinse aid at the bottom of the dishwasher. Have run a "quick rinse" cycle 4 times with no dishwasher soap added and still have sudsing. Can the rinse aid cause oversudin


... Kenmore 15129 Built-in Dishwasher

Leak My dishwasher Danby 22 in. DDW396 is 3 years old. Recently it started to leak from the rear. The water came out slowly from the back but I couldn't tell where the problem is - it leaks when it runs and when it stops working.


Hi there, dishwasher leaking might be due to either of these causes, check these:Main tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the foll ... Danby 22 in. DDW396 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1775 seconds