Having problems with your Maytag 24 in. DWU7402 Built-in Dishwasher ?

Maytag - DWU9502AAM Water will not fill in washcycles but will fill in the rinse cycle. Could this still be the float or is it possible the timer is bad?


Answers :

Hello,\015\012
\015\012From what you are saying yes the timer is bad. It's the only thing that would cause this issue. You can make this repair your self it's simple. Also you can use the link below to look up and order the timer for your dishwasher.\015\012
\015\012Appliance & Refrigerator Parts
Repair Help & Product Troubleshooting for Maytag 24 in. DWU7402 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag - DWU9502AAM Water will not fill in washcycles but will fill in the rinse cycle. Could this still be the float or is it possible the timer is bad?


Hello,\015\012\015\012From what you are saying yes the timer is bad. It's the only thing that would cause this issue. You can make this repair your self it's simple. Also you can use the link below to look up and order the timer for your dishwa ... Maytag 24 in. DWU7402 Built-in Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.


Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher

Miele 868 dishwasher-water fills at begin of cycle,but pump/wash cycle doesn't engage(timer dial still advances,drains at end of cycle.dishwasher was workong,but was moved to a new location ans hasn't worked since.impeller moves freely and pump was rotated via 8mm hex key.is there possibly a reboot/reset, or is there possibly a water pressure issue?-I didn't think so as the dishwasher fills to the prescribed level.


... Miele Dishwashers

12 year old Maytag top of the line dishwasher, won't fill about 1/2 way through the cycle. timer still advances. checked the float assembly, valve, etc. any ideas?


... Maytag DWU9962 Dishwasher

Dishwasher does not fill with water when started. Problem began slowly with dishes not rinsing completely. Overfill float appears to work properly. Water fills pipe leading to fill solenoid but does n


I am almost certain that your problem is the fill solenoid.If it does not work, there will be no water entering your machine.I would either remove it and test it or just replace it at this point.Tim ... Dishwashers

Dishwasher won't fill. replaced fill valve assy. checked float switch it's ok. timer seems to be cycling properly but i'm not getting power to fill valve solenoid. Is it the timer or advance module? and how do I test?


Since you are this deep into the machine, it would be easy to tell if that is the issue by using a meter to test for continuity THROUGH the switches on the timer. It might be the power supply is not working right to send the voltage to that switch. ... General Electric WD21X10013 TIMER

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

Neff 4456 water resevoir not filling. Checked float switch and all OK. Checked water supply and all OK. Filled resevoir manually from top of resevoir and program cycle starts but stops when rinse is required.Have stripped down and cleaned switch with float switches as I have had that problem before getting clogged. Any ideas


... Neff 24 in. S4456 Built-in Dishwasher

I have a dishwasher and the rinse cycle doesn't seem to work. I only know this because the the compartment where the rinse solution goes in is still full when i go to fill it for the next wash. So the solution is not getting used, indicating that the rinse cycle is not rinsing.


The rinse cycle uses very little rinse agent, you may not notice a difference in the level for at least a week or two of daily use. ... Dishwashers

GSD500X-73WB Dishwasher: Automatic timer has stopped working. It is still possible, though, to work the dishwasher manually by turning the dial. How much will it cost to replace the timer? I guess that it is the whole control unit including the timer that would need replacing.


... GE 24 in. GSD500X Built-in Dishwasher

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

We have a kitchenAid dishwasher -- just installed last year new-- we cannot get the rinse aid low light to go off. We have filled it up to where it can no longer hold anymore and the light is still on. I have tried to cut the power on/off and it still remains on. Any suggestions on how to get the light to go off? thank you.


Check to see if the "Heat Dry/Lock" button is lit up. If it is, press the button and hold it for four seconds to unlock your dishwasher controls.Close your dishwasher door firmly and press the "Cancel" button. Wait two minutes for your Ki ... KitchenAid Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Diswasher My grand daughter put regular dis soap into the detergent dispenser and possibly the rinse aid dispenser.I ran it many times without any det erganor rinse aid in it and it still has lots of suds.


EHEHEHEHE. soory to laugh but happens quite frequently. place shallow bowl right side up on lower rack and fill with vinegar, splash some vinegar inbottom of machine as well.run a normal cylce. repeat as needed. vineagar will eat through and break d ... Dishwashers

Miele G 811 SC Intake/Drain Warning Light Appears... Checked out all the usual possibilities, drainage blockages, intake issues, impeller spins in both direction... all are clear, drains and fills properly. Still having the issue, is it possible, the system just needs to be reset? What are your thoughts? Thanks!


I'm having the same problem with my G 811 SC, and have tried the same things, but there aren't any reset buttons (and I called Miele as well as searched the internet for any combination of buttons for resetting it). Anyone have ideas? ... Miele G 2732 SCI Builtin Dishwasher

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

Lost manual. How do you fill up the jet-dry rinse? i filled it up and tightened it but last few washes seemed no difference. Still residue left on dishes. Do i loosen the cap? Thanks!


Your problem could be one of the following:\015\012\015\012* position of dishes, etc. (no obstructions)\015\012* spray arms clogged or non-movement\015\012* water hardness level\015\012* not rinsing dishes, etc. prior to ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a ge dish washer model # gsd2000g00ww and it will continue to pump the water out when triing to fill for wash - i have checked for stuck float - seems to swith ok - i have tried to manually fill but still pumps water out and will not wash


Timer or control ... GE Profile PDW8060GSS Built-in Dishwasher

Doesn't clean properly. fills with water, washes and rinses then drains but dishes still look dirty and spotty. Even tried CLR still dirty.


Www.dishwasherfilter.com will solve your problem. its hard water causing the spots and not your dishwasher. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

The start timer control cycles but nothing happens. The motor seems to gurgle while attempting to fill with water - but no water comes through. We have had this problem before and the repair person replaced the timer control board. Could this be the same problem reoccuring? I have also tapped and cleaned the water float as described by GE website.


I bought a new one and installed it myself. hardest part of installing was taking the old unit out. I compared the cost of a second repair of a 10 year old dishwasher vs. purchasing a new one. We also checked the pump and solenoid to find problems th ... GE Nautilus 24" Built-in Dishwasher

Bottom tray with float gets full of water and won't let water in until I soak it up with a towel. then it will allow water in and continue. Took float out and cleaned still have the problem. What causes the bottom tray to fill with water? Thank You!


Hello JbcmJones, It would appear that the discharge pump isn't allowing the water to properly drain. Sometimes it happens when a glass breaks and parts of the broken glass get down into the sump area and obstruct the drain area. In order to determi ... Bosch SHU3306UC Built-in Dishwasher

Our Asko D1716 dishwasher functions to fill and empty but the pump which causes the sprayers to rotate and distribute the water does not function. The local appliance repairman diagnosed the problem as a bad pump (he called it a motor). Since the pump is a $400 part plus labor, is it possible that the problem is something else like a bad motor capacitor or relay? When the cycle calls for the pump to come on, there is no sound except for a very soft hum.


Hi ! \015\012\015\012Got a D1706 ( in 2002 ) paid $1000 and as os April 2010...same problem as yours, I will trow it away ( dishwasher ) and will never buy at such cost. I'll get a GE or LG. \015\012\015\012Stupid Sweden dish ... Asko D1716 Built-in Dishwasher

We have the same problem. At first, we were getting a horrible detergent film on everything. We thought that was because the detergent cup wasn't opening or the water was too hard or not hot enough. We kicked up the rinse agent as high as possible, switched to a liquid detergent, and only placed shorter items towards the door. The cup still wouldn't open consistently and our dishes still needed to be re-cleaned. We stopped closing the cup. No change. Why would liquid detergent leave a powder fil


You dont need a new dishwasher. it is your water that is causing the film and residue. go to www.dishwasherfilter.com. they have an awesome product that is affordable and g ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1312 seconds