Having problems with your Maytag 24 in. MDB4000 Built-in Dishwasher ?
Front panel is dead, dishwasher won't start - Maytag 24 in. MDB4000 Built-in Dishwasher
Shut power off to machine, take the door apart and see if control panel came unplugged
Repair Help & Product Troubleshooting for Maytag 24 in. MDB4000 Built-in Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Front panel is dead, dishwasher won't start - Maytag 24 in. MDB4000 Built-in Dishwasher
Shut power off to machine, take the door apart and see if control panel came unplugged ... Maytag 24 in. MDB4000 Built-in Dishwasher
Won't start. No lights on front panel. - Maytag 24 in. MDB4651A Built-in Dishwasher
This could be a bad door switch. Check switch for continuity.Also check for burned or broken wires on the door switch and on the timer.The timer could be bad.Hope this helps. ... Maytag 24 in. MDB4651A Built-in Dishwasher
My maytag mdb 5100 dishwasher has blinking lights on front panel, and won't work or start a cycle. What can I do?
... Maytag Dishwashers
Maytag dishwasher, 200 quiet series, front panel (electronics) stuck or shortened, will not start. Is this typical for front electronic strip to shorten (haywire). I noticed a part replacement is 150.00 or more... Am I missing the obvious?
... Maytag Dishwashers
I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want
... Maytag Dishwashers
Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to
Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?
What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher
Dishwasher GSD2030F03WWSA735136B Model Series number;Piece fell off inside front panel, making it impossible to turn on dishwasher at all..so I took off front panel screws, opened dishwasher and saw white plastic piece but can't find where it goes but it must have something to do with turning the knob to start dishwasher because the knob won't turn now..so it must attach inside somehow but I can't figure out where it goes...help!!
I think you need to get a new knob, write down the model number and make and take the pieces to your local domestic appliance supplier, there might be something similar in stock. Now I do mean the kind of small supplier that understands this kind of ... Dishwashers
Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit the start butt
... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher
Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than
... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher
I have a Fisher and Paykel drawer dishwasher and I'm wondering if there's a way to put a panel on it to make it look like and integrated dishwasher. It would need some way of the panel moving to start the dishwasher because the controls are located on the front. I plan on putting it in an Ikea Akurum that is 24" deep. The dishwasher is 22-9/10 deep, so that looks like it would leave some space for the dishwasher to sit back in the cabinet so the door panel could be flush with the cabinet. I'm no
Hmmmm...the first thing that comes to mind is to check out ApplianceArt.com. they have alot of panel options. I'm not sure if they have the integrated ones you are looking for but they have cheap options for everything else. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher
My GSD3600 GE Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit
Hello Greg,\015\012\015\012Your diagnosis is pretty good, but the buzzing suggests it may be the capacitor for the pump motor that has failed rather than the pump motor itself. The capacitor phase-shifts the AC current for starting the mo ... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher
DU943PWKSO DISHWASHER STOPPED WORKING, ELECTRICAL CURRENT TO PANEL BUT DOES NOT START NOR DOES ANYTHING TURN ON. LAST YEAR HAD THE SAME PROBLEM TECH TOOK FRONT APPART AND THE DISHWASHER STARTED WORKING. I ATTEMPTED TO DO SAME BY CHECKING CONNECTIONS BUT NOT WORKING. COULD IT BE THE CIRCUIT PANEL?
Check you electrical power box that feeds to the house. If this dishwasher is hooked up under a sink counter and there is a garbage disposal in the sink area the dishwasher should be hooked up to the same circuit that the dishwasher is hooked to. If ... Whirlpool DU943PWK - Multiple Color Built-in Dishwasher
Maytag MDBtt60awb will not start. Power definitely at dishwasher as panel lights are on, however "start" button does nothing. Dishwasher is less than 2 years old. The panel buttons eventually turn off. I've cycled the power to the unit with no response. The door is definitely latched. Unit ran fine a few days ago.
Most likely you have a bad motor when replacing the motor ihave found it is cheaper to get the pump with the motor attached where as they charge you more money for just the motor or the pump seprately try allbrands appliance parts they seem to be che ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher
Have the same problem as other with the maytag quiet series 300 model MDBS561AWB dishwasher. Two of the buttons on the front light up, but dishwasher will not start. Don't know if CBoard or the buttons or the ribbon cable is the problem. Took the door apart and couldn't find any condensation....Looks like maytag has done it again......could use some help with the cost of replacing all those parts. Will help me decide if better to buy new dishwasher.....preferrably not a maytag or whirlpool, or a
Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al
We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers
Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the
The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher
Diswasher A couple of days ago my dishwasher would not start, there are lights on the front panel and it starts a washing programme but doesn't actually wash anything. I removed the filter from inside the dishwasher and it is full with water, it seems like there is a blokage somewhere. Would a blockage cause the diswasher not to start. Any help on this problem would be greatly appreciated.
Jhgf ... Whirlpool 24 in. ADP6940 Dishwasher
My Maytag MDB9150AWS is no longer working due to what I believe is a electrical fire in the front control panel as there was smoke coming out of the top of the front panel. There were no flames but the smell took your breath away. We had to open the Kitchen windows and door for several hours to try to get rid of the smell, but you can still smell it by the dishwasher. This model is not part of the recall. Has anyone else had a similar problem with this model?
My dishwasher (same make and model) had a similar problem except I did see some sparks coming out from th front on the side of it (on Thanksgiving Day no less - a lot of manual diswahing followed). What the problem ultimatly was is what I believe to ... Dishwashers
I have a Kenwood Slimline Dishwasher KS474s for a year and it has always worked near perfectly. rn However, over the last couple of weeks the dishwasher has not been running the cycles properly (stopping half way through etc, starting the the delay timer half way through cycle), but it always sorted itself after being turned off and starting again. The trouble is now it has got worse.. when I turn it on the panel and lights on the front just flash, the delay sometimes scrolls through on it'
... Kenwood Dishwashers
For the GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher, I reset the breaker on the service panel, the unit is on but I press a wash cycle and press start and nothing happens. Is there a fuse inside the control panel of the dishwasher?
... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher
I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?
HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers
The contol lock LED is illuminated on the front panel of my Maytag dishwasher. (Neither my wife nor I pressed the control lock for 3 seconds!) We've tried to extinguish it by pressing it for 3 to 5 seconds, but it remains ON. We've turned off the breaker to the dishwasher overnight, but when we turn the breaker back On, the contol lock LED comes on. We simply can't unlock the control panel. We can tell that all of the other buttons work just fine because pressing any of them causes the 3 Sec LED
If by pressing the control lock button for 3 seconds does not solves the problem.then there are 3 possibilities due to which this problem may occur\015\0121)the door is not closing properly. the dishwasher door latch is either cracked internally or t ... Maytag Dishwashers
Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?
... Zanussi 23 in. ZDi6053SX Built-in Dishwasher
My Maytag NDB9601 will not start any cycle. You can select the cycle and the display will show the time, but the start and delay buttons, located on the front, not the top with the cycle buttons, will not activate. This leads to the dishwasher not working at all. It worked in the morning, but not in the evening. Dishwasher is 1 year old.
Sounds like a possible door switch problem. \015\012\015\012If you take that area of the door apart, check the ribbon cable for keypad. You can clean the connector with a pencil eraser. ... Dishwashers