Having problems with your Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher ?

I replaced the door latch on my MDW5600AWW & now the spray arms don't spray. I have cleaned the filter and everything accessible from in the tub checks out. I was wondering if I got the 4 wire

\015 I replaced the door latch on my MDW5600AWW & now the spray arms don't spray. I have cleaned the filter and everything accessible from in the tub checks out. I was wondering if I got the 4 wires going to the latch miss located would that have any effect on the wash cycle?\015

Answers :

Repair Help & Product Troubleshooting for Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I replaced the door latch on my MDW5600AWW & now the spray arms don't spray. I have cleaned the filter and everything accessible from in the tub checks out. I was wondering if I got the 4 wire


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers

I own a GE Profile GSD 4330 dishwasher. Recently it has been leaving some water in the bottom of the tub. This water accumulates over time until the entire bottom is filled. I have checked the air vent, garbage disposal unit and the filter in the bottom of the dishwasher (which was filthy). I cleaned the filter and everything else looks okay, but it is still leaving some water in the tub.


... Dishwashers

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

BOSCH dishwasher SHX43 leaves a very thick film on everything. Have tried all kinds of different soaps and spot removers. I tried running unit with no soap and no dishes and noticed a lot of soapy water during washing cycle and still leaving film on stainless steel tub. Have cleaned all filters. Does this unit have trouble codes and how do I access them? Thanks Joeot


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The Heating Element not Working ... Dishwashers

Hi, I've got a SN25M830UK. It starts the programme, then I can hear some noise like a motor is spinning (it happens 2-3 times) and then I get an error E21. I checked the filter and pump cover, there's nothing blocking. Is is a bad pump? How can I access it? Many thanks.


... Siemens Dishwashers

Hello. Have a Neff S5457 that is not working properly. It sounds as though it's working but on getting the crockery out, it is obsvious that it isn't. Have checked all the filters in the machine that are easily checked and all are OK. On taking all the filters out, I can see some philips screwheads in the 'sump' of the machine. Wouldit useful to remove these and see what's under the white plastic covers down there? Are there any other areas that I can check or test? I also wonder if the pump is


Clean the nosels of the arm's, check if the tetergent is pumped (if you have an automatic detergent dispenser) check whit dishwasher unpluget!!! you can check and the pump but be carreful how you put it back. also you can check and the hoses to be cl ... Neff 24 in. S5457X0GB Built-in Dishwasher

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

I posted a question about my Maytag Dishwashere MDBH945AWW not starting, all lights function, and got a response from you seen here in this thread http://www.fixya.com/ThreadView.aspx?thid=6123266&prdid=519913 I was checking the water inlet valve for a clog and have determined with a meter that there is only 25 volts going to the water inlet valve. I notice a blue wire goes to the float switch which I already checked, there are 2 black wires one of which runs towards the back and cant see where


Hi,No, the lights can be working and a relay on the board can still be bad. These things can be very difficult even for a pro to trouble shoot as there can be many things that possibly can cause a unit not to start.From what you are sayin ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Hello I recentley repaired a broken door latch on chef electronic diswasher the push button type not the rotary switch style. i had to disconnect the circuit board I wrote down the were the wires connected i have discovered that when I reconnected everything i had not got all the wires in the right place is there any way I can get a wiring diagram so I can connect the wires correctly thank you


Unfortunately as i know it is difficult to find a wiring diagram. Better try an authorized service station where they may have similar appliances. ... Dishwashers

At the end of the cycle the water is not draining out of the tub. I vac'ed out the water, removed the filters and checked for debris but found non.


Check drain hose first.If you do not find any blockage, then you will need to access the pump, remove pump hose and look for blockage in there.If there is no blockage at all, then either the water level switch, a faulty pump ( ... Bosch SHV46C03 Built-in Dishwasher

IE message Getting an IE message on dishwasher. Water is coming into the tank and heating, but after about 5 minutes, it kicks into an IE error. We have checked the water inlet and the spray arms and everything appears okay. I have read the comments about checking the float, but how do you do this? Any other suggestions would be helpful.


My solution was, after LG sent me a second dishwasher that ALSO did not work, to demand a refund. Then I went and bought a KitchenAid~ it's awesome! ... LG LDF6810 Built-in Dishwasher

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

Westpoint Dishwasher I have a Westpoint Dishwasher. As soon as I press the start button the Machine goes on sound like it is working then all of a suddon it stops. Now it have 5 red lights burning and beeping when I switch it on. Do you know what the problem can be? Checke the water checked the filter everything is clean and working.


I put the mahcine on as normal but it does not go past the first cycle of the red flashing light? ... Dishwashers

Our bosch dishwasher runs but no water is spraying on the inside. Is there a water filter clean out or is there a water pump that might be broken? I checked the line coming in and it isn't plugged. I made sure where the stainless line goes into the electric valve that it wasn't plugged to that point. I could see anywhere else to check if it was plugged. I figure there has to be a water pump, but I guess I'm not sure of that either. Thanks for any help..


Hi, welcome to Fixya. \015\012 \015\012By the description you've provided, it sound's like the wash motor is either seized or just stuck, let's hope it's the later. \015\012 \015\012Bosch had issued a service tip about this ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

Have Fisher-Paykel DD603 double-drawer dishwasher. Top drawer motor making loud noise. )Bottom drawer fine.) Still seems to wash and definitely pumps water but sounds like a "motor with a broken belt." Checked filter and rotating spray arm - no problems. (Found a little broken glass in filter; could be very old.) Suggestions?


If glass has gotten past the screen and into the pump, you may have a pcs. logged in the pump housing.\015\012Best way to correct this, is to remove the pump inlet and outlet lines and flush out with a water hose.\015\012Keep ... Dishwashers

My dishwasher made some really grindy, crunchy sounds the last time it worked. I unscrewed the float and checked for debris in it, nothing there. When I got that off, there was a circular black fan-type thing under it(the motor??), that spins around and seems to be held in place with only one screw. I tried to access underneath that, and it doesn't want to do anything but spin around. How do I remove that to check underneath?? I don't want to break it. I put it all back together and tried run


One of the most common question that I get on a dishwasher repair is "how does that motor and pump impellor screw come out?"Inside many dishwasher pump assemblies is a screw that goes through the upper impellor and screws direct ... Whirlpool 24 in. DU930PWP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1239 seconds