Having problems with your Maytag 24 in. MDB6100A Built-in Dishwasher ?

I have an model MDB6100, 6160 that won't start. The "normal wash", "heated dry", and "clean" lights are flashing but no matter what button I push, nothing changes.


Answers :

Repair Help & Product Troubleshooting for Maytag 24 in. MDB6100A Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an model MDB6100, 6160 that won't start. The "normal wash", "heated dry", and "clean" lights are flashing but no matter what button I push, nothing changes.


... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work


... Frigidaire Dishwashers

The glass xpress light on my Whirlpool GU 2400, Quiet Partner III, is flashing. I tried alternating the sani rinse and heated dry buttons, and alternating hi-temp wash and heated dry---nothing changed. None of the option buttons light up when they are pushed. and the time remaining stays on -- (two dashes), the dashes don't move. Any other ideas?? PLEASE


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

I own a Maytag MDB5100AWB three lights are flashing on the panel, the clean button, rinse only and heavy wash. I've tried turning off the breaker for 20 minutes, pushing the buttons in sequence, holding them down, nothing seems to work. It's done this before and a repairman pushed the buttons and it worked. Is there anything I can do to avoid another service call?


... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

I have a blinking cancel light on model GU1200xtlt1 and will not start in any cycle. Also if I push another button it flashes rinse button and cancel button. Before this it ran in Sani Clean over and over again and I could not change the cycle. I emptied out a bit of water from the bottom because it did not drain also and the water was not smelling too good.


... Whirlpool Dishwashers

Frididair GLD2250RDC0 The lights on the selection buttons (Normal cycle, pots and pans, no heat dry etc) flash when pressed. When the start button is pushed, it sounds like the cycle is starting, but nothing reallyhappems.


Sounds like the very common control panel issue. They have a tendency to short out due to overheating. It is possible it is the motor is bad, you can test power to motor with a voltmeter. If no power, then try power from control panel to motor. If th ... Frigidaire 24 in. GLD2350RCC Professional Built-in Dishwasher

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

GE dishwasher Model GLD4560n00ss Control panel won't change when buttons are pushed. Two lights keep flashing-Normal Wash and Heated Dry Beeps once a minute Water won't fill


... GE Dishwashers

My kenmore ultrawash model #665.17362301 clean light is flashing and it won't start. Have googled how to reset, but the buttons it gives to push I do not have, I do not have heat dry option. Does anyone know another solution to reset?


... Dishwashers

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

I have a whirlpool quiet partner II dishwasher model # DU1055XTVB5 and the normal light is steady flashing I have did the sequence to reset HEATED DRY NORMAL HEATED DRY NORMAL and the normal light continues to flash and if I push the cancel/drain button then it starts a steady flash


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

Rinse only light is on and all of the wash rinse sanitize clean buttons come on and flash when you try to start it, if you change the setting to normal or heavy duty the wash light comes on then the rinse only light comes on and all above mentioned buttons flash until the tub is drained.


Hi\015\012 \015\012Try and reset the dishwasher by unplugging it for 5-10 minutes. Now check if you are still getting the same error you can try and press the following buttons to reset it-- \015\012Saini Rinse, He ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1854 seconds