Having problems with your Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher ?

Dishwasher short cycles and shots off

\015 My dishwasher only runs for two minutes and shuts off, no matter what cycle it is set for. The control board was replaced and it still does the same thing. I was told that there is a series of codes that can be used to reset the board. Is this true and what would they be? Is this even the problem?\015

Answers :

Batty, you can put the dishwasher in a automatic test mode or manual test mode. For automatic press the heavy wash key 5 times followed by the start key. 88 should show in the display if you have the digital display. It's going to check the wash motor, fill valve, drain motor, soap dispenser, vent and heater automatically. If any of these systems fail, you will get a code. The test will finish by itself. You can get the information to test the touch panel by getting the tech sheet from behind the bottom toe panel. Catriver..post back.
Repair Help & Product Troubleshooting for Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher short cycles and shots off


Batty, you can put the dishwasher in a automatic test mode or manual test mode. For automatic press the heavy wash key 5 times followed by the start key. 88 should show in the display if you have the digital display. It's going to check the wash mot ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Own a KitchenAid dishwasher, model KDC-21AD. Unit stopped shortly after startup cycle began. When cycling thru the various wash cycles, I hear a slight hum when selector switch is at the "pots/pan" selection. About 2" of water is standing in base of dishwasher and it will not start. Checked the KitchenAid site and they do not list my dishwatcher. Would like to be able to repair myself or have it done at reasonable price.


... KitchenAid Dishwashers

My Beko D3422 FS was washing normally and the residual current device tripped approximately half way through the cycle. I have unplugged the dishwasher and checked the plug socket with various other appliances. None have tripped the RCD. I have stripped the Dishwasher to look for any disconnected terminals or shorted wires and cannot find anything obviously burnt or any signs of shorting. The 13amp fuse in the dishwasher plug is fine. Are there any components I can test or replace which wouldgi


... Dishwashers

Water fill solenoid receives only 10 volts on normal cycle-not enough juice to open solenoid. Dishwasher does not fill. Dishwasher works fine on short cycle because on that setting the control panel sends 120V to the fill solenoid. Is there a ciricuit board or fuse I can replace?


It's most likely the timer set the timer to when it is gonna fill to a normal wash hook up a volt meter when it is in its fill stage make sure it is putting out 120 volts ... GE Nautilus 24" Built-in Dishwasher

Help! My dishwasher runs thru it's cycles but when I open it I find my second detergent cup still full of soap and my dishes still dirty. I have an older maytag dishwasher but have never had this problem with it. I've tried running a short prewash cycle with the soap despenser open to wash out the soap from the open second despenser but it doesn't wash it out. I know water is coming out of the spray arms but can't see if the arms are spinning although when running it does sound like they ar


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not to open. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Dishwashers

I have Jenn-Air dishwasher that I use the heated dry cycle for. Last night at 11:00 pm or so I ran the unit. Today at 10:00am when I opened the door steam barrelled out and everything was so hot to the touch I gave myself a significant burn when grabbing a non-metal item in the dishwasher. Should I be concerned there is a problem with the entire unit or just the heated dry cycle? Should I be concerned about fire danger due to a short?


... Jenn-Air 24 in. JDB2100AW Dishwasher

My Bosch dishwasher, model SHX46A05UC/30 has been working fine. I ran it once today on the Power Scrub Plus cycle (always use this one). Shortly after unloading the dishwasher I needed to run it again with more dishes. Within a few minutes of running the dishwasher I heard loud, almost grinding noises. Nothing appears to be stuck. Any ideas on what to do? This dishwasher has always been quiet up until today.


... Bosch 24 in. SHX36L05UC Stainless Steel Built-in Dishwasher

Silly Dishwasher Hello, I have a huge problem with my less-that-12-hour-old Bosch SGS56E18GB. We are not generally thick people. We plumbed our dishwasher in, like we have plumbed in many appliances. Switched on the dishwasher for the first time and GREAT!!! Here we go! I can tell this is not going to be plain sailing. The dishwasher has already decided that it wishes to do the short cycle. (19/29mins or something) I Press on then off - no change. Reset, Off - on, still no change. So I decided t


Press and hold scrub and delicate at the same time for 3 seconds then let it cycle turn off it should reset. ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

After starting the cycle, the dishwasher starts and runs normally for a short time, then the water drains out of the tub prematurely while the cycle is still going. The machine then runs dry until the cycle times out. At the next cycle and the process repeats. It started as a sporadic problem, but is getting worse.


You may have a faulty drain valve,the drain valve is under dishwasher there are two clips on each side check,with applance store for replacement part. ... Maytag 24 in. MDBH940AWS Built-in Dishwasher

For Miele Dishwasher G2470SCVI Need help with remaining water in the bottom. Model# G2470 SCV1 SF Type-HG03. Runs through the entire cycle,long,short ect..everything is clean and dishes look great but


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Belt, Water Pump\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

KUDS30IXSS1 dishwasher will pump out water completely on the one hour wash cycle, leaves water in tank at end of all other cycles. Will completely drain when cancel/drain cycle is pushed. Is there a re-set code, or sequence; or is there a diagnostic code or sequence tohelp me? Like push Heat/dry, then normal wash, then Heat/dry, then normal wash within 6 or 7 secs? Or is my circuit board just shot?


... Dishwashers

Hi, I have a Miele G638 Plus dishwasher and the Red Inlet/Drain light comes on shortly after the wash cycle starts. I have cleaned everything out and the impellor moves freely. I have also made sure the outlet is clear. I have tried resetting and repeating on different washing cycles but it always locks out after the washing cycle starts. Could this be a heater problem as the element looks quite corroded? I have had side panels off and the water appears to flow easily through the sid


Hi\015\012\015\012Thanks for using FixYa. The first\015\012thing that should be checked is if its draining properly as it could be that\015\012the drain hose is clogged an ... Miele 24 in. G638 Plus Free-standing Dishwasher

I have an equator PLS600 and I can't seem to get it to work. I have tried the WikiFix to help a stalled dishwasher, by adding water and vinegar. When I put on the wash cycle it does not run. Even with the short rinse cycle, the sprayer will not move, and the machine will just run through the cycle until it starts to drain. Please help!!! Thanks =)


Give the spray arm a spin to make sure it rotates. It should spin freely. If not, remove plastic spray arm clip, flip it over, replace it, and try again. Make sure holes in the spray arm are clear of debris. Spray arm must be clean for it to spin ... Equator 20 in. PLS600 Free-Standing Dishwasher

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene


... Kenmore Dishwashers

Dishwasher is shorting out power supply when on hot cycle


The wash tank heater is likely the issue.Remove the 2 wires on the heater and tape them up and run a cycle,let me know. ... Dishwashers

Dishwasher cycle too short


... Whirlpool GU2400XTP Built-in Dishwasher

Our whirlpool ADP 6565 dishwasher stops very close to but short of the end of the cycle, with the on-button flashing. If we press that button for a few seconds, it starts again and completes the cycle. I have cleared the filter on the inlet hose because we use tank water which does have particles in it frm time to time, but this made no difference.


It appears that you have a timer malfunction. at the point that the timer stop, you need to listen closely to any sound from the timer. if no sounds emerges, repalce timer ... Whirlpool Dishwashers

Indesit dishwasher hi i have an indesit IDL40 slimline dishwasher which has developed a fault.It started by not cleaning the dishes properly and now it starts the cycle but stops shortly afterwards with lights 1 & 2 flashing.Please help.


Machine is flooded in base\015\012means you have a leak in dishwasher\015\012dismantle check feed pipe to top basked probable faulty feed pipe replace if so ... Dishwashers

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers

My kitchenaid dishwasher will not complete a washing cycle. the water heating seems to be staying on all the time. could my heating element be shot. the water seems hot when i open the dish washer during the cycle but it is connected to the hot water supply line. thanks


... KitchenAid Dishwashers

Have a Kenmore dishwasher #665.1677993, approx. 13 years old. Upon starting new cycle the pump turns on for a few short seconds, then off, then after a couple minutes it goes on again for a few seconds then off, then later in the cycle it does stay on for a longer period of time. In conjuntion with this intermitent problem it has begun leaking out the bottom of the front door. I have checked drain line, check valve, strainer/screen and vent in the door. I assume it is an electrical issue?


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1313 seconds