Having problems with your Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher ?

I can't select a cycle. The buttons quit working.

\015 I can't select a cycle. The buttons quit working. We have a Maytag MDB7601AWS and after about one year the buttons quit working. The only cycle we can use is some 5 minute cycle that does not clean anything. The display lights quit working as well. Some of the lights work on the display but some don't. Any one else know anything about whether we should repair or trash it and buy?\015

Answers :

It sounds like the touchpad is gone,phone the manufacture and see how much it will cost ,and then take it from there
Repair Help & Product Troubleshooting for Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

I can't select a cycle. The buttons quit working.


It sounds like the touchpad is gone,phone the manufacture and see how much it will cost ,and then take it from there ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

Cycle buttons work, option buttons dont, Cant deselect heated dry, Wont start


I had the same symptoms and the front panel was the fixthe part with the buttons on it ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Frigidaire dishwasher does not start. but i see the cycle select LED light come on . all of a sudden the dishwasher stopped working. all buttons except the "start" work. i can select 'normal', 'pots n pans', select the delay etc, but the START button will simply not work!


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

Our Frigidaire Dishwasher buttons stopped working. If we push normal cycle it will not select as well as other cycles. The last time it happened the maintenance guy came and turned it on and off and it started working again. That didn't work this time. We still can't select some of the wash buttons


You will have to replace that selector switchhttp://tclaundryrepair.com/ ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

What buttons do I push to actually make my dishwasher work. The power blinked off and I cant remember what button to push to make it work. It is a GE stainless steal quiet 3 dishwasher


Try turning breaker off for about 2 minutes and then retry. This shold rest controls for you. ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

My stupid Candy CDI45 refuses to work when I turn it on and try to select a programme. It seems that the PR button (to select a programme) doesn't work anymore. Anyone?


... Dishwashers

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a frigidaire series 4000 model FDB4315LFS1 and the display will show PF if i unplug it for 5 min and plug it back in however i cant get the control buttons to work. is shows no sign of life. holding buttons for 3 secs wont work either.


Hi\015\012\015\012PF error means power\015\012failure, if reset wont work then let it remain unplugged for 15 minutes and in\015\012this time take a hair blower and blow air on the control panel as this will\015\012blow away the moi ... Frigidaire Dishwashers

My Maytag NDB9601 will not start any cycle. You can select the cycle and the display will show the time, but the start and delay buttons, located on the front, not the top with the cycle buttons, will not activate. This leads to the dishwasher not working at all. It worked in the morning, but not in the evening. Dishwasher is 1 year old.


Sounds like a possible door switch problem. \015\012\015\012If you take that area of the door apart, check the ribbon cable for keypad. You can clean the connector with a pencil eraser. ... Dishwashers

ADP6000WH/ADP6000IX Whirlpool Dishwasher. The controls are not working correctly. When I select the top two (Strong and Normal) settings I hit the start button the dishwasher will not run. When I select the other four (Economy, Rinse, glass and soak) settings the machine works fine. Thanks MB


... Whirlpool Dishwashers

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

Countdown display is flashing saying 2:10 but dishwasher does not respond to pushing any of the buttons (light stays on Power Scrub and does not respond to selecting other wash cycles). On'Off button works but none of the other buttons responds. Machine does not begin washing when door is closed


... Bosch SHE6AP0 Builtin Dishwasher

Dishwasher: Whirlpool Gold Quiet Partner. Has worked fine until had a house plumbing blockage which made water pool in the bottom of the dishwasher as well as kitchen sink. Tried to get it to drain at first using keypad. Drain light clicked on and then off because there was nowhere for water to do. Manually emptied most of the water, then "Cancel/Drain" worked if I held it down quite a while. House plumbing is now fixed. However the keypad only works sporadically now. Some buttons do so


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Dishwasher does not start, on any cycle selection. the only button that works is the cancel button which tells me the unit has power. this has happened before and a service tech was called and it "magically" started after he pushed the cancel button, not so this time??


Make sure the floor is dry where you are standing. \015\012 \015\012Push the cancel button twice in quick succession to attempt to turn the washer off.\015\012 \015\012Open the door all the way and look over t ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

My Maytag MDB7609AWS 's start button is not working - cycle selection lights work (not blinking)


... Maytag MDB7609AWS Builtin Dishwasher

Whirlpool Quite Partner IV. Cancel button works


... Dishwashers

KitchenAid KUDS011IBS0 select keypad buttons no longer working


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1177 seconds