Having problems with your Maytag 24 in. MDB9150A Built-in Dishwasher ?

Stops in the middle of the wash cycle

\015 My dishwasher runs part way thru the wash cycle and then stops washing. It does continue a blipping noise that isn't loud, but still isn't washing the dishes. It will stay there forever unless I manually turn it off. I can then start the wash cycle again from the beginning, and it does the same thing all over again, runs for about 20 minutes on the wash cycle and then stops washing but with a blipp, blipp, blipp noise. Anything I can do, is it the computer chip ? I know nothing ! Thanks !\015

Answers :

Same problem, it was a poor solder on the main control board. I pulled the inside cover off the front door and saw where the circuit board had gotten hot. The little blue box was loose so I pulled the circuit board loose, flipped it over, and resoldered it.
HAVE THE SAME PROBLEM WITH THE SAME MAYTAG MODEL DISHWASHER. THE PROBLEM IS WITH THE CONTROL PANEL ASSEMBLY HAVING ONBOARD COMPONENTS NOT SODERED CORRECTLY TO THE MAIN CONTROL BOARD. THESE LOOSE OR COLD SOLDER CONNECTIONS HAVE TO BE REHEATED,RESOLDERED WITH A SOLDERING IRON . THE ON BOARD COMPONENTS THAT I WAS HAVING PROBLEMS WITH WAS THE BLUE BOX LOOKING COMPONENT,SOLID STATERELAY, AND THE RAISED RESISTOR,HAS COLORED BANDS AROUND IT. THESE COMPONENTS ARE LOCATED ON THE LEFT SIDE OF THE PRINTED CIRCUIT BOARD FACING THE DISHWASHER LOOKING OVER THE TOP. TO MAKE THE REPAIR, TURN OFF THE CIRCUIT BREAKER TO THE DISHWASHER, OPEN THE FRONT DOOR AND REMOVE THE 10 SCREWS THAT HOLD THE DOOR TOGETHER. THIS WILL ALLOW ACCESS THE THE CONTROL PANEL.. IF YOU DO NOT FEEL QUALIFIED TO MAKE THIS REPAIR USING A LOW WATTAGE SOLDERING IRON YOU CAN ORDER THE CONTROL ASSEMBLY LED FROM PARTSSELECT.COM. FOR ABOUT 100 DOLLERS. THEY ARE ABOUT THE CHEAPEST. FOLLOW THE ON SCREEN INSTRUCTIONS TO ORDER THIS ASSEMBLY.THE ASSEMBLY PART CAN BE FOUND IN THE CONTROL PANEL PARTS ILLUSTRATION. WHEN SEARCHING FOR THIS PART YOU MUST SEARCH USING YOUR DISHWASHER MODEL NUMBER. THIS INFORMATION CAN BE FOUND ON THE LEFT SIDE OF THE TUB OF THE DISHWASHER AFTER OPENING THE FRONT DOOR. ALSO, WHEN LOOKING FOR THIS PART IT WILL BE LISTED TWICE,AS SERIES 10, OR SERIES 24. YOU MUST ORDER THE CORRECT SERIES. THE SERIAL NUMBER ON THE SAME PLATE THAT THE MODEL NUMBER WILL PROVIDE THIS INFORMATION. IF YOUR SERIAL NUMBER STARTS WITH A 10 ORDER THE SERIES 10, WITH A 24, ORDER THE SERIES 24. WHILE YOU ARE ORDERING CHECK YOUR LATCH HANDLE, THE SIDE PIN WAS BROKEN MAKING IT HARD TO OPEN THE DISHWASHERS FRONT DOOR. ONE OTHER THING YOU MIGHT WANT TO CHECK IS THE FLOAT SWITCH OPERATION. MINE WAS STICKING. TO ACCESS THIS REMOVE THE 4 SCREWS THAT HOLD THE PANEL .THE FLOAT SWITCH IS LOCATED TO THE LEFT.WITH THIS PANEL REMOVED CHECK FOR ITS FREE NONSTICKING OPERATION. IT CAN BE DISMANTLED AND CORRECTED. A SERVICE SHEET IS LOCATED, ATTACHED TO THE INSIDE OF THIS PANEL.IT HAS GOOD TROUBLESHOOTING INFORMATION INCLUDING A AUTOMATIC FUNCTION TEST.THIS TEST PROVIDES A DIAGNOSTIC ANALYSIS THAT WAS EXTREMELY HELPING FOR ME TO DETERMINE MY PROBLEM AND CORRECT THE MALFUNCTION CONSIDERING I AM NOT A APPLIANCE REPAIRMAN. I HOPE THIS INFORMATION IS BENEFITICAL. REGARDS.
Repair Help & Product Troubleshooting for Maytag 24 in. MDB9150A Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Stops in the middle of the wash cycle


Same problem, it was a poor solder on the main control board. I pulled the inside cover off the front door and saw where the circuit board had gotten hot. The little blue box was loose so I pulled the circuit board loose, flipped it over, and resol ... Maytag 24 in. MDB9150A Built-in Dishwasher

My D3112 Asko dishwasher controls will not respond. There is a pump or motor running non-stop, even after I push the power off buton. The only way to make it stop is to unplug power cord. It is almost like it is stuck in the middle of a wash cycle program, but the water is not spraying inside nor is the heater or dryer cycle appear to be on.


... Asko D3112SS Stainless Steel Dishwasher

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

When the water cycle is running there is a white plug by the water inlet that is leaking. When the dishwasher is not in the water cycle it does not leak. When the dishwasher is stopped in the middle of the wash cycle and water in in the bottom of the pan it does not leak. It only leaks when the water is running.


Crack in water inlet valve or a pin hole in the hose going from the valve to side of tub spraying water where you see it. You have a holein someting. You need to trace it back to its sourse. When you say "water is running"im guessing thats when its f ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Bosch Dishwasher (model SHU43C05UC17/17) will not power power on after stopping in the middle of a wash cycle. AC power is present at input and water supply is connected and supplying water.


... Bosch 24 in. SHU5305UC Built-in Dishwasher

My dishwasher a ge profile mod# PDW7900N10WW was in middle f a speed cycle when it stopped and reset itself to a normal wash and then stopped and blanked as if there was no power i checked the circut breaker and made sure the detergent in the dispenser was filled what could the problem be


... GE Dishwashers

GE GSDJ5940F00ss - stopped in the middle of a wash cycle, went to the dry cycle and beeped and beeped and beeped. had a free wire replacement but htat did not fix. Is it the control panel?


Yes it is the control board and is more than likely from a cold soldier on the board as this is very common. ... Maytag Dishwasher

Hi i recently started to have issue with my dishwasher. The issue is that the washer stops in the middle of the washing cycle. More specific, once i start, it stops about 20 second latter. Once i push the door of the washer it start to work again for another few seconds any ideas?


There is some mechanical problem.Check water flow. Free rotation of spray arms. Refer user guide. ... Dishwashers

Drain/ Inlet red light flash in the the middle of washing cycle and then dish waher stopped. Drain cleaned a few time. It works a cycle and does do the same next time


Check float /i.e drain hose/ must be in as built positions ... Miele Dishwashers

I have an electronic operating Kitcheaid Dishwasher. It has a tendency to stop in the middle of a cycle without warning. This can happen at different times of the day and at different stages of washing. We open the door, make sure the racks are pushed in tight and close and hold the door tight for a few moments. The dishwaser comes back on, but this can repeat in the course of one wash.


I would try adjusting the strike which is a little metal piece coming off of the tub that goes into the door when you close it. the strike may not me latching properly ... Dishwashers

The dishwasher stops in the middle of the wash cycle. I then have to push in on the door and it begins again. This happens very often, 10 plus times per wash,


Faulty or loose door safety switch,,,check for mounting screws loose,,or wear on door catch,,if not loose or wear,,faulty switch,,replace. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Dishwasher completely stopped in the middle of a washing cycle. Any suggestions? I checked and there's no issues with power. It's old and I think something may have been shorted or blown. help ple


It sounds like the timer. I have replaced the timer because I had the same problem. It now works perfect! ... Hotpoint 24 in. HDA1000G Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

My Dishwasher stops in the middle cycle. This happens after about an hour of work and it stops when the machine starts spraying water and there is a hump noise


... Dishwashers

GE Nautilus Dishwasher stops in the middle of cycle


... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

Whirlpool Undercounter Dishwasher DU8900XY1, My dishwasher is dead. It stopped in the middle of the wash cycle and has not operated since. I checked the power at the junction box and power was confirmed. I could not see or smell any burnt wires. I don't know the next thing to trouble shoot to fix the problem. Please help


Take off the kick panel and open up the j-box at the dishwasher only. Just make sure there is no burned wire nut or loose one\012\012Thanks ... Whirlpool Dishwashers

My dishwasher just stopped working in the middle of the wash cycle. It seems to have no power to it. I have checked all the circuit breakers and reset them all and still nothing. Any ideas?


Your hard wiring maybe bad, or a wire nut came off call electritian or someone who knows electricity ... Whirlpool 24 in. GU980SCG Built-in Dishwasher

No power. Stopped in the middle of a wash cycle. Checked breaker, fine Does this have a fuse some where?


... Kenmore 13593 Stainless Steel Built-in Dishwasher

Danby DDW1802W - Dishwasher stopped dead in the middle of wash cycle. Lights are on, but absolutely nothing else is happening. Help, please.


... Danby DDW1802W Built-in Dishwasher

Model #DU1050xtpb3. I can' get it to wash. It stopped in middle of cycle. The green light on the clean button flashes 7 times then skips about 20 then starts blinking 7 times again.


Hi,This machine was made by Whirlpool and the flashing clean light is a common error code for them. If\015\012the clean light is the one flashing then your dishawasher could have a\015\012heater circuit problem (depending on t ... Whirlpool Dishwashers

My DW60 Hotpoint stopped in the middle of wash. all panel lights flashing at the top left. water colected at the base. tried to restart with a fresh cycle. program selection successful. drained all the water. loaded fresh water. but giving grumpy noice and not the usual thrust start.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My dishwasher stop working in the middle of washing cycle. The water has not drained out completely. I attempted to restart the dishwasher but it appears there is no power. I checked the power auto swithch/fuze on the master fuze board. There is still no power going through the dishwasher.


... Dishwashers

Kenmore dishwasher 665.16879 power light and wash light flashing after stopping in the middle of a cycle. after a while it started up again for whatever reason.


... Dishwashers

Our bosch diswasher on auto wash will stop functioning in middle of the cycle start beeping and there is an icon of a faucet on the display. What does this mean?


Did you ever solve this issue?my bosch has started doing the same thing. it will complete the cycle though, just with a really annoying constant beep.i checked to see if there was low water pressure coming in but everything seems normal. ... Bosch Dishwashers

Dishwasher stopped working in the middle of wash cycle- none of the lights are on.


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1379 seconds